Hi There are two products called IPAQ. One was a desktop computer, the other was a PDA. The desktop will run anything, the PDA can handle some of the BSD's and Linux's. Both need to be configured / compiled to match the device.
Bob On Aug 16, 2013, at 2:44 PM, Chris Albertson <[email protected]> wrote: > What OS runs on the IPAQ? > > Did you have to re-build LH from source? > > Edit: OK now I see you are running some other software called > "thunderhead". Same questions apply > > > On Thu, Aug 15, 2013 at 1:17 PM, Robert Atkinson > <[email protected]>wrote: > >> Hi Chris, >> I've posted this before, but it's worth saying again. I use the PocketPC >> version of Lady Heather on an IPAQ. These are available for next to nothing >> on Ebay and can run in a dock on the bench or you can gut it and embed it >> in a cased Thunderbolt. worn out batteries are not an issue as we have >> constant power available. They just need 5V. One with an SD card slot is >> good so you don't have to re-load the code from a PC if the power does go >> out. >> >> >> Robert G8RPI. >> >> >> ________________________________ >> From: Chris Albertson <[email protected]> >> To: Discussion of precise time and frequency measurement < >> [email protected]> >> Sent: Wednesday, 14 August 2013, 18:36 >> Subject: Re: [time-nuts] ThunderBolt Display >> >> >> What was the problem you found. Other then a "new to you" platform? I'm >> trying to understand why reading serial data would be hard. >> >> An advantage of the Adruino is that you don't need to make a PCB. Even if >> you want to do something like add a graphical display or and SD card for >> logging they just plug in, no solder required. >> >> Of course the pre-buillt display is even easier but can't be modified. >> >> One of my loner term goals is to move lady heather like functions onto a >> small uP based device. It seems wasteful to use a PC for this. >> >> >> On Wed, Aug 14, 2013 at 10:16 AM, Russ Ramirez <[email protected] >>> wrote: >> >>> Yeah, after trying to (reliably) get the time out of the pertinent TSIP >>> message using an Arduino UNO, I can understand your statement Adam about >>> the Arduino approach. It kinda works, but it felt like I was fighting the >>> implementation of the controller card and that I should cut-over to my >> own >>> solution using an Atmel, PIC or TI chip that I could just load C code >> into. >>> One of this lists members gave me the code I needed, so ironically using >>> the UNO made the project more difficult. >>> >>> Russ >>> K0WFS >>> _______________________________________________ >>> time-nuts mailing list -- [email protected] >>> To unsubscribe, go to >>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >>> and follow the instructions there. >>> >> >> >> >> -- >> >> Chris Albertson >> Redondo Beach, California >> _______________________________________________ >> time-nuts mailing list -- [email protected] >> To unsubscribe, go to >> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >> and follow the instructions there. >> _______________________________________________ >> time-nuts mailing list -- [email protected] >> To unsubscribe, go to >> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >> and follow the instructions there. >> > > > > -- > > Chris Albertson > Redondo Beach, California > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
