I have also done this to older oscillators and it works. When you look at the caps in the unit, if you are lucky somehow you may be able to see what type they are. Yes silver mica but there are various qualities and tempco's. Try to match the quality if at all possible. Otherwise guess. Good luck and its not the worst issue you will run into. Just maybe thats why you obtained the oscillator in the first place. Hey bad stuff is my friend. Regards Paul WB8TSL
On Fri, Dec 8, 2017 at 11:31 AM, Jeremy Nichols <[email protected]> wrote: > My HP-103AR frequency standard has a similar problem. I have been advised > to take it apart and replace one of the capacitors in order to bring the > frequency back into the range of adjustment. Sounds like you have the same > problem. > > Jeremy > > > On Fri, Dec 8, 2017 at 7:52 AM paul swed <[email protected]> wrote: > > > I took a quick look at the spec sheet. > > It appears coarse adjustment is an option M and would actually be a pot. > > That speaks to another tuning diode for coarse? Or a pot on pot > > arrangement. > > That sounds ugly. > > Regards > > Paul > > WB8TSL > > > > On Fri, Dec 8, 2017 at 10:17 AM, Bob kb8tq <[email protected]> wrote: > > > > > Hi > > > > > > It is quite possible that nothing is actually broken and that the > crystal > > > has simply drifted > > > outside the tuning range. It should be pretty easy to spot the coarse > > > tuning device once > > > the package is open. I would bet you will find a selected capacitor > > across > > > the coarse tune or in > > > series with the coarse tune. Changing the value of that cap should > bring > > > things back on > > > frequency. I would avoid changing caps across the EFC tuning diode. > > > > > > Bob > > > > > > > On Dec 8, 2017, at 8:05 AM, Ulf Kylenfall via time-nuts < > > > [email protected]> wrote: > > > > > > > > > > > > Gentlemen, > > > > We have an Oscilloquartz OCXO 8600-3that cannot any longer be > adjusted > > > into 5,000,000 Hz.It is about 1 Hz out of 5 MHz and turning > > > coarse/fineadjustment potentiometers cannot bring the frequencyinto its > > > specification. > > > > Oven temperature is about + 80C accordingto the thermistor and the > > > operating voltageis at 24 VDC. > > > > Have Googled but the only thing that turns upis datasheets w/o any > > > details. > > > > Before I take it apart and start lookingfor obviously broken > > components, > > > isthere anyone that has a CLIP on this unit? > > > > 73 > > > > > > > > Ulf Kylenfall - SM6GXV > > > > _______________________________________________ > > > > time-nuts mailing list -- [email protected] > > > > To unsubscribe, go to https://www.febo.com/cgi-bin/ > > > mailman/listinfo/time-nuts > > > > and follow the instructions there. > > > > > > _______________________________________________ > > > time-nuts mailing list -- [email protected] > > > To unsubscribe, go to https://www.febo.com/cgi-bin/ > > > mailman/listinfo/time-nuts > > > and follow the instructions there. > > > > > _______________________________________________ > > time-nuts mailing list -- [email protected] > > To unsubscribe, go to > > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > > and follow the instructions there. > > > -- > Sent from my iPad 4. > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to https://www.febo.com/cgi-bin/ > mailman/listinfo/time-nuts > and follow the instructions there. > _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
