---------- Forwarded message ----------
From: basem aljedai <[EMAIL PROTECTED]>
Date: Sun, Apr 13, 2008 at 5:15 PM
Subject: Re: [Tinyos-help] TinyOS help
To: Ittipong Khemapech <[EMAIL PROTECTED]>
HI lttipong ,
Thanks a lot for your help , I have done what you side to mukesh and my
code have become like this :
BaseStationP:
uses {
.
.
.
interface CC2420Packet as rssiReader;
}
event message_t *RadioReceive.receive[am_id_t id](message_t *msg,void
*payload,uint8_t len)
{
// my modification ....
RssiMsg* rssiStruct = (RssiMsg) (payload); // here error :
conversion to non-scalar type requested
rssiStruct -> rssi = call rssiReader.getRssi(msg);
uartQueue[uartIn] = rssiStruct -> rssi; // here warning:
assignment makes pointer from integer without a cast
//end of modification
return receive(msg, payload, len);
}
this the struct where I hold the data ..
#ifndef RSSIMSG_H
#define RSSIMSG_H
enum {
AM_RSSIMSG = 10
};
// This sturct will hold the RSSI ..
typedef nx_struct RssiMsg
{
nx_int8_t rssi;
} RssiMsg;
#endif
should I use the struct in the sender and the receiver(BaseStation) .. or it
is enough to use it in BaseStation only .. ?
is there a way to collect the data using MIG tool .. or any other rather
than Listen .. ?
Thanks a lot
Basem ;
On Fri, Apr 11, 2008 at 7:51 PM, Ittipong Khemapech <
[EMAIL PROTECTED]> wrote:
> You have already declared several variables to store RSSI and LQI at the
> receiving side (base station). The other thing you have to do is to put
> those values into the payload of the message_t.
>
> An example of defining your own message structure is:
>
> #ifndef SAMPLEMSG_H_
> #define SAMPLEMSG_H_
>
> enum {
> AM_SAMPLEMSG = 10
> };
>
> typedef nx_struct SampleMsg {
> nx_uint8_t txpower; // Current tx power
> nx_int8_t rssi; // RSSI
> nx_uint8_t lqi; // LQI
> } SampleMsg;
>
> #endif
>
> About the current tx, you have to get it at the sending side NOT the
> receiving one.
>
> Hope this helps.
>
> Ittipong
>
>
> On 11/04/2008, mukesh rungta <[EMAIL PROTECTED]> wrote:
>
> > Yes it doesnt displays anything.
> >
> > What do u mean by declaring your own message structure??
> > I dont understand this..
> > I am using the message_t *msg from RadioReceive.receive event and
> > calling CC2420 packet
> > to read Rssi/Lqi.
> > also I have declared a pointer type for storing these values of Rssi/Lqi
> >
> > and I just receive a warning while compiling that "assignment make
> > pointer from integer without
> > a cast".
> >
> > Can u elaborate on this.
> >
> > thanks
> >
> > On Fri, Apr 11, 2008 at 11:27 AM, Ittipong Khemapech <
> > [EMAIL PROTECTED]> wrote:
> >
> > > >>But when I use serial listen to see the packet values it doesnt
> > > displays
> > > anything.
> > >
> > > What does it mean exactly? Did you have 00 all the time OR nothing was
> > > shown on PC screen?
> > >
> > > If it's the latter case, I think you forgot to declare your own
> > > message structure.
> > >
> > >
> > > Ittipong
> > >
> > > On 11/04/2008, mukesh rungta <[EMAIL PROTECTED]> wrote:
> > >
> > > > Hi
> > > >
> > > > Thanks for forwarding my mail to list.
> > > >
> > > > I am using Tmote sky, TinyOS, on xubuntos....
> > > >
> > > > I modify the following..
> > > > BaseStationC
> > > > .
> > > > .
> > > > components CC2420ActiveMesageC
> > > > .
> > > > .
> > > > BaseStationP.CC2420Packet -> CC2420ActiveMessageC
> > > >
> > > > In BaseStationP
> > > > uses{
> > > > .
> > > > .
> > > > interfacce CC2420Packet;
> > > > }
> > > > after event RadioReceive.receive
> > > > rssi = call CC2420Packet.getRssi(msg);
> > > > lqi = call CC2420Packet.getLqi(msg);
> > > > pow = call CC2420.getPower(msg);
> > > >
> > > > uartQueue[uartIn] = rssi;
> > > > . .
> > > > ..
> > > >
> > > > Now when I compile my code and it successfully compiles.
> > > > But when I use serial listen to see the packet values it doesnt
> > > > displays
> > > > anything.
> > > >
> > > > I dont know why.
> > > >
> > > > Mukesh
> > > >
> > > >
> > > > On Fri, Apr 11, 2008 at 5:09 AM, Ittipong Khemapech <
> > > > [EMAIL PROTECTED]> wrote:
> > > >
> > > > > Firstly, I have forwarded your email to the list. You can have
> > > > > better help and suggestions.
> > > > >
> > > > > Secondly, what your codes say?
> > > > >
> > > > > Thirdly, which platform, os, tinyos are you using?
> > > > >
> > > > > Ittipong
> > > > >
> > > > >
> > > > > On 11/04/2008, mukesh rungta <[EMAIL PROTECTED]> wrote:
> > > > > >
> > > > > > Hi
> > > > > >
> > > > > > I am also working on to find out the RSSI/LQI using BaseStation.
> > > > > > What I did was programmed few motes with BlinkToRaadio and
> > > > > > one mote connected to computer as BaseStation. Now I modified
> > > > > > this
> > > > > > program to read and display the values of RSSI, LQI and received
> > > > > > power
> > > > > > instead of transmitted message from other nodes. But I am not
> > > > > > able to
> > > > > > read these. I guess there is some problem in my code.
> > > > > >
> > > > > > I guess you are also working in the same thing. I hope you can
> > > > > > help me
> > > > > > in this regard. I will appreciate your reply.
> > > > > >
> > > > > > Thanks
> > > > > > Mukesh
> > > > > >
> > > > >
> > > > >
> > > >
> > >
> >
>
> _______________________________________________
> Tinyos-help mailing list
> [email protected]
> https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
>
--
Basem M Al-jedai
--
Basem M Al-jedai
_______________________________________________
Tinyos-help mailing list
[email protected]
https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
