Hi It works! Thank you so much for all your help :) I have one final question though. I need to interface the GPS information with the rest of our project, which is written in TinyOS and Java. Would you happen to know the packet format of the data packet so that I can parse it and use it without MoteView? Or is there some way to send MoteView data over a socket or something?
Thanks! Nikhil On Mon, Apr 21, 2008 at 11:36 AM, Giri Baleri <[EMAIL PROTECTED]> wrote: > Here's something I would suggest you to try. > Program your MTS420 sensor Mote with /apps/xmesh/XMTS420 app and node ID > non-zero > Program the Base Mote with /apps/XMeshBase app and node ID=0 > Then use XServe or MoteView to read the data. > > Giri > > ------------------------------ > *From:* Nikhil Singhal [mailto:[EMAIL PROTECTED] > *Sent:* Sunday, April 20, 2008 11:39 PM > > *To:* Giri Baleri > *Cc:* [email protected]; Siirtola Harri > *Subject:* Re: [Tinyos-help] re: GPS module of MTS420 not working > > Hi > > I have acquired the MoteWorks SDK and installed the patch as given on the > web page. I'm now running into a problem with actually getting the data. > > I have a MIB520 programming board, a micaZ board and the MTS420CC GPS mote > (with the ublox chip). I installed TestMTS420cc application > (apps/xsensor/XSensorMTS420CC/) on one mote, and attached the GPS board to > it. I then installed XSniffer on another mote, which stayed hooked up to the > computer. I run MoteView with the database mts420_results, but I don't see > any sensor information showing up in the table. Also, when I tried sniffing > the data with XSniffer and xlisten, I get a stream of data with no fixed > size (that xlisten is unable to parse). > > I would really appreciate any help with this as I'm completely stuck. > > Thank you! > > Nikhil > > On Tue, Feb 19, 2008 at 12:48 PM, Giri Baleri <[EMAIL PROTECTED]> wrote: > > > This patch was written/tested on MoteWorks SDK. I don't know if it > > would work seamlessly in any version of TinyOS. > > > > Giri > > > > ------------------------------ > > *From:* Nikhil Singhal [mailto:[EMAIL PROTECTED] > > *Sent:* Friday, February 15, 2008 8:55 PM > > *To:* Giri Baleri > > *Cc:* [email protected]; Siirtola Harri > > > > *Subject:* Re: [Tinyos-help] re: GPS module of MTS420 not working > > > > Thanks! I do have the new MTS420CC board. I downloaded the drivers > > from the link you sent. I have a question though: Do I need to load the > > /opt/tinyos-1.x/contrib/xbow/apps/XSensorMTS400 app or the > > /opt/tinyos-1.x/contrib/xbow/apps/xmesh/XMTS420CC app? I get a ton of > > compile errors when I try to compile the xmesh one, and the XSensor one > > still doesn't give me GPS data when I use XListen. I did change the > > SENSORBOARD variable in the XSensor makefile to mts420cc. Is it possible > > that I'm using an old version of TinyOS, or am I doing something > > incorrectly? This is the output I get: > > > > [2008/02/15 23:35:46] > > MTS420 [sensor data converted to engineering units]: > > health: node id = 2 > > battery: = 3278 mv > > humidity: = 28 % > > Temperature: = 26 degC > > IntersemaTemperature: = -78 degC > > IntersemaPressure: = -402 mbar > > Light: = 0.192361 lux > > X-axis Accel: = 533.333333 mg > > Y-axis Accel: = 96.446701 mg > > > > [2008/02/15 23:36:06] > > MTS420 [sensor data converted to engineering units]: > > health: node id = 2 > > battery: = 3278 mv > > humidity: = 28 % > > Temperature: = 26 degC > > IntersemaTemperature: = -78 degC > > IntersemaPressure: = -402 mbar > > Light: = 0.486144 lux > > X-axis Accel: = 533.333333 mg > > Y-axis Accel: = 101.522843 mg > > > > Thanks for all the help! > > > > On Fri, Feb 15, 2008 at 11:36 AM, Giri Baleri <[EMAIL PROTECTED]> wrote: > > > > > Do you know if you are using MTS420CA/CB or MTS420CC? The latter has > > > a uBlox GPS receiver and requires newer GPS drivers. These are available > > > in > > > MoteWorks and an update has been posted to our knowledgebase. > > > > > > http://www.xbow.com/Support/wobjectDetail.aspx?id=50160000000KuHhAAK&type=Solution&page=0 > > > > > > If you try to use older GPS drivers with the new MTS420CC, you might > > > not get GPS data. > > > > > > If you believe that you have the older board and are using compatible > > > older drivers, please check your GPS antenna connections and make sure > > > that > > > it is placed outdoors with optimal sky visibility. > > > > > > I hope that helps, > > > Giri > > > > > > ------------------------------ > > > *From:* [EMAIL PROTECTED] [mailto: > > > [EMAIL PROTECTED] *On Behalf Of *Nikhil > > > Singhal > > > *Sent:* Friday, February 15, 2008 3:04 AM > > > *To:* Siirtola Harri > > > *Cc:* [email protected] > > > *Subject:* Re: [Tinyos-help] re: GPS module of MTS420 not working > > > > > > It seems like I am getting all the MTS400 data, and that there > > > should be a separate packet with the GPS data which, if is 0x0a packet is > > > the heartbeat, never arrives. > > > > > > Any ideas? > > > > > > Thanks! > > > > > > On Fri, Feb 15, 2008 at 5:43 AM, Siirtola Harri <[EMAIL PROTECTED]> > > > wrote: > > > > > > > IIRC, the 0x0a packet is the heartbeat (health) packet that motes > > > > send indicating they're alive. Might be that XListen won't parse it but > > > > it's > > > > not the source of your problem. The parsed packet also looks odd, > > > > considering there should be some GPS info. Although it reads MTS420, is > > > > the > > > > MTS400 app sending all required data? > > > > > > > > Sorry, haven't used MTS420 but wrote just to give something to think > > > > about. > > > > > > > > Regards, > > > > > > > > Harri > > > > > > > > ------------------------------ > > > > *From:* [EMAIL PROTECTED] [mailto: > > > > [EMAIL PROTECTED] *On Behalf Of *Nikhil > > > > Singhal > > > > *Sent:* Friday, February 15, 2008 11:38 AM > > > > *To:* [email protected] > > > > *Subject:* [Tinyos-help] re: GPS module of MTS420 not working > > > > > > > > Hi all > > > > > > > > In my previous message, I had mentioned that I was using XListen > > > > with a CrossBow MTS420 mote and wasn't getting any output on the > > > > screen. As > > > > it turns out, my sensor board was faulty. I'm using another one now, > > > > and I > > > > get readings from all the other sensors, but nothing from the GPS. I > > > > have > > > > installed the XSensorMTS400 app on the board, and am using TinyOS 1.x. > > > > This > > > > is the output I get: > > > > > > > > [2008/02/15 04:31:31] > > > > error: no packet handler for tos type 0x0a > > > > [2008/02/15 04:31:31] > > > > MTS420 [sensor data converted to engineering units]: > > > > health: node id = 2 > > > > battery: = 3278 mv > > > > humidity: = 28 % > > > > Temperature: = 25 degC > > > > IntersemaTemperature: = 24 degC > > > > IntersemaPressure: = 1011 mbar > > > > Light: = 4.600000 lux > > > > X-axis Accel: = 616.666667 mg > > > > Y-axis Accel: = 116.751269 mg > > > > > > > > I'm guessing that the line "error: no packet handler for tos type > > > > 0x0a" might be the problem, but I have no idea how to fix it. Any help > > > > would > > > > be highly appreciated! > > > > > > > > Thanks! > > > > > > > > -- > > > > Nikhil Singhal > > > > > > > > > > > > > > > > -- > > > Nikhil > > > > > > > > > > > -- > > Nikhil > > > > > > -- > Nikhil > -- Nikhil
_______________________________________________ Tinyos-help mailing list [email protected] https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
