Try comparing the "uisp" command lines that are generated by working and not working examples, and maybe run them by hand.
It also could be that you don't have a good download file and the error message is wrong...check through the build output directories to see what is actually there. MS Ranjani Nagarajan wrote: > Hi Michael, > > Thanks a lot for your email. I have been able to deploy and run Blink > application on the sensors, but when I tried to deploy Agilla this > problem surfaced. I have also tried /dev/ttyS0 but that didn't help. I > have checked the device manager for the serial port and it is COM1. I > have tried with different cases for COM1 (com1 and COM1) but that didn't > help either. > > Thanks, > Ranjani > > On Tue, Jan 13, 2009 at 5:53 AM, Michael Schippling <[email protected] > <mailto:[email protected]>> wrote: > > Have you been able to download anything to your micas > or is it just failing on the real program you want to use? > Are you sure the COM1 is the right port? > You might try using "/dev/ttyS0" instead of COM1 as well. > > MS > > Ranjani Nagarajan wrote: > > Hi there, > > I am trying to deploy Agilla on Mica2 sensors. Agilla is a > middleware that helps in development of mobile agents > (http://www.cs.wustl.edu/mobilab/projects/agilla/). I am using > TinyOS 2.x. I am able to compile Agilla but I am facing the > following problem while deploying: > > Command: make mica2 reinstall,1 mib510,com1 > Cygwin: C:\Crossbow\cygwin\bin > Directory: > C:\Crossbow\cygwin\opt\MoteWorks\apps\general\Agilla\nesc\agilla\ > "/opt/MoteWorks/tools/bin/ide.pl 'make mica2 reinstall,1 > mib510,com1' > 'C:\Crossbow\cygwin\opt\MoteWorks\apps\general\Agilla\nesc\agilla\'" > ############################# > ide.pl Ver:$Id: ide.pl,v 1.1.2.1 2006/05/29 07:22:52 lwei Exp $ > Executing: /opt/MoteWorks/apps/general/Agilla/nesc/agilla/ bash > -c "make mica2 reinstall,1 mib510,com1" > set-mote-id build/mica2/main.srec build/mica2/main.srec.out-1 1 > installing mica2 binary using mib510 > uisp -dprog=mib510 -dserial=com1 --wr_fuse_h=0xd9 > -dpart=ATmega128 --wr_fuse_e=ff --erase --upload > if=build/mica2/main.srec.out-1 > Error: No error > make: *** [program] Error 1 > -> \\.\COM1 > > > Process Exit Code: 0 > > Time Taken: 00:02 > > > I am not sure why this is happening and the error is not very > descriptive. Please let me know if you have faced similar > problem before or if you have any ideas about why this may be > happening. I will really appreciate your help. > > Thanks, > Ranjani > > > > ------------------------------------------------------------------------ > > _______________________________________________ > Tinyos-help mailing list > [email protected] > <mailto:[email protected]> > > https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help > > > -- > Platform: WinXP/Cygwin > TinyOS version: 1.x, Boomerang > Programmer: MIB510 > Device(s): Mica2, MicaZ, Tmote > Sensor board: homebrew > > -- Platform: WinXP/Cygwin TinyOS version: 1.x, Boomerang Programmer: MIB510 Device(s): Mica2, MicaZ, Tmote Sensor board: homebrew _______________________________________________ Tinyos-help mailing list [email protected] https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
