Hi Michael, I found that all of a sudden the Blink application is also not getting deployed. However, the Blink application already deployed is working (Red LED blinks once per second). I find that the first time I try to execute the "make mica2 reinstall mib510,com" command, it hangs after the uisp commandline. If I invoke it again, I get the error :
Error: No error -> \\.\COM1 make: *** [program] Error 1 I am not sure why this is happening. Thanks, Ranjani On Wed, Jan 14, 2009 at 6:26 AM, Michael Schippling <[email protected]>wrote: > Try comparing the "uisp" command lines that are generated > by working and not working examples, and maybe run them by hand. > > It also could be that you don't have a good download file and the > error message is wrong...check through the build output directories > to see what is actually there. > > MS > > Ranjani Nagarajan wrote: > >> Hi Michael, >> >> Thanks a lot for your email. I have been able to deploy and run Blink >> application on the sensors, but when I tried to deploy Agilla this problem >> surfaced. I have also tried /dev/ttyS0 but that didn't help. I have checked >> the device manager for the serial port and it is COM1. I have tried with >> different cases for COM1 (com1 and COM1) but that didn't help either. >> >> Thanks, >> Ranjani >> >> On Tue, Jan 13, 2009 at 5:53 AM, Michael Schippling >> <[email protected]<mailto: >> [email protected]>> wrote: >> >> Have you been able to download anything to your micas >> or is it just failing on the real program you want to use? >> Are you sure the COM1 is the right port? >> You might try using "/dev/ttyS0" instead of COM1 as well. >> >> MS >> >> Ranjani Nagarajan wrote: >> >> Hi there, >> >> I am trying to deploy Agilla on Mica2 sensors. Agilla is a >> middleware that helps in development of mobile agents >> (http://www.cs.wustl.edu/mobilab/projects/agilla/). I am using >> TinyOS 2.x. I am able to compile Agilla but I am facing the >> following problem while deploying: >> >> Command: make mica2 reinstall,1 mib510,com1 >> Cygwin: C:\Crossbow\cygwin\bin >> Directory: >> C:\Crossbow\cygwin\opt\MoteWorks\apps\general\Agilla\nesc\agilla\ >> "/opt/MoteWorks/tools/bin/ide.pl 'make mica2 reinstall,1 >> mib510,com1' >> >> 'C:\Crossbow\cygwin\opt\MoteWorks\apps\general\Agilla\nesc\agilla\'" >> ############################# >> ide.pl Ver:$Id: ide.pl,v 1.1.2.1 2006/05/29 07:22:52 lwei Exp $ >> Executing: /opt/MoteWorks/apps/general/Agilla/nesc/agilla/ bash >> -c "make mica2 reinstall,1 mib510,com1" >> set-mote-id build/mica2/main.srec build/mica2/main.srec.out-1 1 >> installing mica2 binary using mib510 >> uisp -dprog=mib510 -dserial=com1 --wr_fuse_h=0xd9 >> -dpart=ATmega128 --wr_fuse_e=ff --erase --upload >> if=build/mica2/main.srec.out-1 >> Error: No error >> make: *** [program] Error 1 >> -> \\.\COM1 >> >> > Process Exit Code: 0 >> > Time Taken: 00:02 >> >> >> I am not sure why this is happening and the error is not very >> descriptive. Please let me know if you have faced similar >> problem before or if you have any ideas about why this may be >> happening. I will really appreciate your help. >> >> Thanks, >> Ranjani >> >> >> >> ------------------------------------------------------------------------ >> >> _______________________________________________ >> Tinyos-help mailing list >> [email protected] >> <mailto:[email protected]> >> >> https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help >> >> >> -- Platform: WinXP/Cygwin >> TinyOS version: 1.x, Boomerang >> Programmer: MIB510 >> Device(s): Mica2, MicaZ, Tmote >> Sensor board: homebrew >> >> >> > -- > Platform: WinXP/Cygwin > TinyOS version: 1.x, Boomerang > Programmer: MIB510 > Device(s): Mica2, MicaZ, Tmote > Sensor board: homebrew > >
_______________________________________________ Tinyos-help mailing list [email protected] https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
