thank you . At some point I'll see about making it easier to find on the wiki.
On Fri, Feb 24, 2012 at 1:47 AM, Mubashir Rehmani <[email protected]>wrote: > Here is the source > http://enl.usc.edu/enl/trunk/tenet/doc/Recompile_Mote_Binary.HOWTO > > Regards > > On 24 February 2012 10:46, Eric Decker <[email protected]> wrote: > >> what are you quoting from? >> >> >> On Fri, Feb 24, 2012 at 1:19 AM, Mubashir Rehmani >> <[email protected]>wrote: >> >>> Hello, >>> >>> Please see below to change the channel for CC2420 >>> >>> 4.1. Modify the RF channel frequency >>> >>> - You can change the RF channel frequency used by the motes. >>> For example, to change the RF channel of the motes with CC2420 radio >>> (e.g. telosb, micaz), put the following line at the end of the file >>> 'tenet/mote/apps/Makerules' and compile and install both >>> 'tenet/mote/apps/Tenet' and 'tenet/mote/apps/BaseStation': >>> >>> CFLAGS += -DCC2420_DEF_CHANNEL=<your_channel> >>> >>> where '<your_channel>' is the channel number in the range [13~26]. >>> >>> >>> 4.2. Modify the RF transmit power >>> >>> - You can change the RF transmit power used by the motes. >>> For example, to change the TX power of the motes with CC2420 radio >>> (e.g. telosb, micaz), put the following line at the end of the file >>> 'tenet/mote/apps/Makerules' and compile and re-install both >>> 'tenet/mote/apps/Tenet' and 'tenet/mote/apps/BaseStation': >>> >>> CFLAGS += -DCC2420_DEF_RFPOWER=<your_power> >>> >>> where '<your_power>' is the channel number in the range [3~31]. >>> >>> >>> Regards >>> Mubashir Husain Rehmani >>> >>> >>> >>> On 24 February 2012 10:16, Sergio Valcarcel <[email protected]>wrote: >>> >>>> Hi, >>>> >>>> I did it a long time ago for the CC2420. It is easy but I do not >>>> remember how to exactly. >>>> I suggest you to enter into the platform, chipset or cpu directory and >>>> look for your particular radio chipset header. You will find the right >>>> module and method there. >>>> >>>> Cheers! >>>> Sergio >>>> >>>> On Fri, Feb 24, 2012 at 8:32 AM, Prasanth P <[email protected]>wrote: >>>> >>>>> Dear all, >>>>> >>>>> How can i select channel for communication in nesc programming. Am >>>>> using Telosb mote. >>>>> >>>>> Thanks in advance. >>>>> >>>>> -- >>>>> Regards >>>>> Prasanth.P >>>>> >>>>> >>>>> _______________________________________________ >>>>> Tinyos-help mailing list >>>>> [email protected] >>>>> >>>>> https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help >>>>> >>>> >>>> >>>> _______________________________________________ >>>> Tinyos-help mailing list >>>> [email protected] >>>> https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help >>>> >>> >>> >>> >>> -- >>> Mubashir Husain Rehmani >>> >>> >>> >>> _______________________________________________ >>> Tinyos-help mailing list >>> [email protected] >>> https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help >>> >> >> >> >> -- >> Eric B. Decker >> Senior (over 50 :-) Researcher >> >> >> > > > -- > Mubashir Husain Rehmani > > > -- Eric B. Decker Senior (over 50 :-) Researcher
_______________________________________________ Tinyos-help mailing list [email protected] https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
