Steve,
You might get a better response if you showed a little more courtesy
and gratitude for the *free* help you are receiving here:
http://www.tuxedo.org/~esr/faqs/smart-questions.html
So, what exactly do you mean "trying to edit and not at all
successfully"? Do you not know how to use a text editor, or what? Apache
will not recognize changes to the configuration file without a restart. Did
you do that? What kinds of changes are you trying to make?
Roger Whitcomb
Computer Associates
Senior Software Engineer
Development
Phone: +1 408 965 8653
FAX: +1 408 965 8805
[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>
-----Original Message-----
From: STEVE R BURRUS [mailto:[EMAIL PROTECTED]]
Sent: Monday, June 24, 2002 3:53 PM
To: Tomcat Users List
Subject: How do you edit the conf file for Apache???
Rory, I emailed you earlier today, but YOU HAVE NOT SEEN FIT to respond back
to me
yet, so I thought that I would give you another "electronic shout" again
now. I
installed Apache just last nite, so I was at least trying to edit the conf
file,
but not at all successfully!! Can you help me please? SRB
****************************************************************************
*******
--- "Douglas, Rory" <[EMAIL PROTECTED]> wrote:
> Just sending this again to see if I can get #@!!***$ Outlook NOT to send
> HTML mail!
>
> I haven't set-up anything really complex but the following setup should
> work. I haven't got around to trying load-balancing, if anyone does that
and
> gets it working, please share!
>
> -------------------------------
> in HTTPD.CONF (in Apache2\conf)
> -------------------------------
> LoadModule jk2_module modules/mod_jk2.dll
>
> -------------------------------------
> in JK2.PROPERTIES (in Tomcat4.1\conf)
> -------------------------------------
> I just commented out everything. Note that if you are using an AJP
connector
> with port other than the default of 8009 you should specify here (where it
> says channelSocket.port). If you comment everything out JK seems to
default
> to 8009 (and then 8010, 8011 and so on if you have more than one
connector).
> If you want need specific ports for multiple connectors then specify
> channelSocket.port multiple times e.g
>
> channelSocket.port=8014
> channelSocket.port=8018
>
> if you have two AJP connectors specified in server.xml with port numbers
> 8014 and 8018.
>
> ----------------------
> in WORKERS2.PROPERTIES
> ----------------------
>
> I just copied this file from tomcat4.1\jtc-src\jk\conf into Apache2\conf
and
> edited it a bit. The really important bits seem to be:
>
> [channel.socket:localhost:8009]
> info=Ajp13 forwarding over socket
> debug=20
> tomcatId=Tomcat-Standalone
>
> that actually sets up a worker. I understand that you can specify
>
> group=someGroupName
>
> and create groups of workers for load-balancing. I also believe that every
> worker created without specfiying a group is in the default group (I think
> it is "lb").
>
> To map contexts use [uri:] blocks like so:
>
> [uri:/test]
> info=Test context mapping
> debug=20
> context=/test
>
> Again, here you can specify which workers serve that context by specifying
> group=groupName
>
> It's a good idea to keep these parts around too:
>
> [status:]
> info=Status worker, displays runtime informations
>
> [uri:/jkstatus/*]
> info=Display status information and checks the config file for changes.
> group=status:
>
> you can then hit http://yourapacheserver/jkstatus and get a loads of jk
info
> that might help you catch config errors
>
> There are some docs in tomcat4.1\jtc-src\jk\doc\jk2 that might help (but
> they're not great).
>
> Hope this is useful to someone
> cheers
> Rory
>
>
> Rory Douglas
> Sun Chemical Corporation
> (201) 224-4600 x133
> [EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>
> > --
> To unsubscribe, e-mail:
<mailto:[EMAIL PROTECTED]>
> For additional commands, e-mail:
<mailto:[EMAIL PROTECTED]>
__________________________________________________
Do You Yahoo!?
Yahoo! - Official partner of 2002 FIFA World Cup
http://fifaworldcup.yahoo.com
--
To unsubscribe, e-mail:
<mailto:[EMAIL PROTECTED]>
For additional commands, e-mail:
<mailto:[EMAIL PROTECTED]>
