last night I installed xvid4 and tried it. Still it stops at 98.94%. I did get it to run in command line and it went all the way thru, but, the output file was not there. Here is an error message that shows up when dvdrip starts:
[EMAIL PROTECTED]:~# dvdrip Pango-WARNING **: Error loading GPOS table 4097 at /usr/lib/perl5/site_perl/5.8.8/Gtk2/Ex/FormFactory.pm line 108. (xvid4conf:2926): Pango-WARNING **: Error loading GPOS table 4097 And here is the log file from dvdrip: Wed Jan 23 13:59:28 2008 Start job 'Transcode multipass - title #1' Wed Jan 23 13:59:28 2008 Start job 'Transcode video - title #1, pass 1' Wed Jan 23 13:59:28 2008 Executing command: mkdir -m 0775 -p '/root/dvdrip-data/UltraViolet/tmp' && cd /root/dvdrip-data/UltraViolet/tmp && mkdir -p /root/dvdrip-data/UltraViolet/avi/001 && execflow -n 19 transcode -H 10 -a 0 -x vob -i \/root\/dvdrip\-data\/UltraViolet\/vob\/001\/ -w 2000,50 -F mpeg4 -b 128,0,2 -s 2.015 --a52_drc_off -f 24,1 -M 2 -R 1 -y ffmpeg,null --psu_mode --nav_seek /root/dvdrip-data/UltraViolet/tmp/UltraViolet-001-nav.log --no_split -o /dev/null --print_status 25 && echo EXECFLOW_OK Wed Jan 23 14:02:09 2008 Transcode video - title #1, pass 1: 10% done. Wed Jan 23 14:04:26 2008 Transcode video - title #1, pass 1: 20% done. Wed Jan 23 14:06:52 2008 Transcode video - title #1, pass 1: 30% done. Wed Jan 23 14:09:14 2008 Transcode video - title #1, pass 1: 40% done. Wed Jan 23 14:11:31 2008 Transcode video - title #1, pass 1: 50% done. Wed Jan 23 14:13:53 2008 Transcode video - title #1, pass 1: 60% done. Wed Jan 23 14:16:13 2008 Transcode video - title #1, pass 1: 70% done. Wed Jan 23 14:18:41 2008 Transcode video - title #1, pass 1: 80% done. Wed Jan 23 14:21:00 2008 Transcode video - title #1, pass 1: 90% done. Wed Jan 23 14:26:00 2008 Sending signal 9 to PID(s) 4154, 4157 Wed Jan 23 14:26:01 2008 Job 'Transcode multipass - title #1' cancelled Wed Jan 23 14:26:02 2008 Job 'Transcode video - title #1, pass 1' cancelled Wed Jan 23 14:26:19 2008 Project file saved to '/root/dvdrip-data/UltraViolet.rip' Thu Jan 24 03:22:45 2008 Start job 'Transcode multipass - title #1' Thu Jan 24 03:22:45 2008 Start job 'Transcode video - title #1, pass 1' Thu Jan 24 03:22:45 2008 Executing command: mkdir -m 0775 -p '/root/dvdrip-data/UltraViolet/tmp' && cd /root/dvdrip-data/UltraViolet/tmp && mkdir -p /root/dvdrip-data/UltraViolet/avi/001 && execflow -n 19 transcode -H 10 -a 0 -x vob -i \/root\/dvdrip\-data\/UltraViolet\/vob\/001\/ -w 2000,50 -b 128,0,2 -s 2.015 --a52_drc_off -f 24,1 -M 2 -R 1 -y xvid,null --psu_mode --nav_seek /root/dvdrip-data/UltraViolet/tmp/UltraViolet-001-nav.log --no_split -o /dev/null --print_status 25 && echo EXECFLOW_OK Thu Jan 24 03:36:22 2008 Transcode video - title #1, pass 1: 10% done. Thu Jan 24 03:47:31 2008 Transcode video - title #1, pass 1: 20% done. Thu Jan 24 04:00:37 2008 Transcode video - title #1, pass 1: 30% done. Thu Jan 24 04:12:37 2008 Transcode video - title #1, pass 1: 40% done. Thu Jan 24 04:23:39 2008 Transcode video - title #1, pass 1: 50% done. Thu Jan 24 04:35:04 2008 Transcode video - title #1, pass 1: 60% done. Thu Jan 24 04:46:14 2008 Transcode video - title #1, pass 1: 70% done. Thu Jan 24 04:57:34 2008 Transcode video - title #1, pass 1: 80% done. Thu Jan 24 05:09:16 2008 Transcode video - title #1, pass 1: 90% done. ----- Original Message ----- From: CRAIG CONRAD <[EMAIL PROTECTED]> To: Transcode-Users <transcode-users@exit1.org> Sent: Wed, 23 Jan 2008 22:33:04 -0500 (EST) Subject: [transcode-users] New to transcode- Having trouble getting a complete conversion Hello- I am new to transcode, but i do have some experience with linux. I have a problem with transcode or dvdrip. When I rip a dvd everything goes fine, I then go to the transcode screen and start the process. This all appears fine until it gets to 98.94% complete, then it just hangs. I am using FFmpeg- mpg4 codec to put it in an .avi file , 2000 manual bitrate, 1 pass or 2, no zoom or crop. I ran dvdrip in debug mode and I got an error message because xvid4conf was not installed, so I installed that and the message went away, but it still hangs. My system is an Acer Laptop AMD64 running slAMD64 11.0. This has been a good stable OS for me, even with all the 32bit programs I have installed. Thanks. Craig C
