Hi again,
After some further work with these pathces. (I currently work on a
SIL3114 driver using them)
It seems like there is a "lot" of code duplication in libata.h and the
existant ata.h. Thus making it impossible to include both ones. Which i
would like to do.
Pasted below is the modifications i did to do to get it working.
Could one perhaps merge the differences? Or is there other suggestions on
how to solve this?
/Tor
--- ../u-boot/include/ata.h 2008-02-28 07:40:55.000000000 +0100
+++ u-boot/include/ata.h 2008-03-18 11:53:43.000000000 +0100
@@ -84,43 +84,45 @@
#define ATA_LBA 0xE0
enum {
- ATA_MAX_DEVICES = 1, /* per bus/port */
- ATA_MAX_PRD = 256, /* we could make these 256/256 */
- ATA_SECT_SIZE = 256, /*256 words per sector */
+ ATA_MAX_DEVICES = 1, /* per bus/port */
+ ATA_MAX_PRD = 256, /* we could make these 256/256 */
+ ATA_SECT_SIZE = 256, /*256 words per sector */
/* bits in ATA command block registers */
- ATA_HOB = (1 << 7), /* LBA48 selector */
- ATA_NIEN = (1 << 1), /* disable-irq flag */
- /*ATA_LBA = (1 << 6), */ /* LBA28 selector */
- ATA_DEV1 = (1 << 4), /* Select Device 1 (slave) */
- ATA_DEVICE_OBS = (1 << 7) | (1 << 5), /* obs bits in dev reg */
- ATA_DEVCTL_OBS = (1 << 3), /* obsolete bit in devctl reg */
- ATA_BUSY = (1 << 7), /* BSY status bit */
- ATA_DRDY = (1 << 6), /* device ready */
- ATA_DF = (1 << 5), /* device fault */
- ATA_DRQ = (1 << 3), /* data request i/o */
- ATA_ERR = (1 << 0), /* have an error */
- ATA_SRST = (1 << 2), /* software reset */
- ATA_ABORTED = (1 << 2), /* command aborted */
+ ATA_HOB = (1 << 7), /* LBA48 selector */
+ ATA_NIEN = (1 << 1), /* disable-irq flag */
+ /*ATA_LBA = (1 << 6), *//* LBA28 selector */
+ ATA_DEV1 = (1 << 4), /* Select Device 1 (slave) */
+ ATA_DEVICE_OBS = (1 << 7) | (1 << 5), /* obs bits in dev reg */
+ ATA_DEVCTL_OBS = (1 << 3), /* obsolete bit in devctl reg */
+ ATA_BUSY = (1 << 7), /* BSY status bit */
+ ATA_DRDY = (1 << 6), /* device ready */
+ ATA_DF = (1 << 5), /* device fault */
+ ATA_DRQ = (1 << 3), /* data request i/o */
+ ATA_ERR = (1 << 0), /* have an error */
+ ATA_SRST = (1 << 2), /* software reset */
+ ATA_ABORTED = (1 << 2), /* command aborted */
/* ATA command block registers */
- ATA_REG_DATA = 0x00,
- ATA_REG_ERR = 0x01,
- ATA_REG_NSECT = 0x02,
- ATA_REG_LBAL = 0x03,
- ATA_REG_LBAM = 0x04,
- ATA_REG_LBAH = 0x05,
- ATA_REG_DEVICE = 0x06,
- ATA_REG_STATUS = 0x07,
- ATA_PCI_CTL_OFS = 0x02,
+ ATA_REG_DATA = 0x00,
+ ATA_REG_ERR = 0x01,
+ ATA_REG_NSECT = 0x02,
+ ATA_REG_LBAL = 0x03,
+ ATA_REG_LBAM = 0x04,
+ ATA_REG_LBAH = 0x05,
+ ATA_REG_DEVICE = 0x06,
+ ATA_REG_STATUS = 0x07,
+ ATA_PCI_CTL_OFS = 0x02,
/* and their aliases */
- ATA_REG_FEATURE = ATA_REG_ERR,
- ATA_REG_CMD = ATA_REG_STATUS,
- ATA_REG_BYTEL = ATA_REG_LBAM,
- ATA_REG_BYTEH = ATA_REG_LBAH,
- ATA_REG_DEVSEL = ATA_REG_DEVICE,
- ATA_REG_IRQ = ATA_REG_NSECT,
+ ATA_REG_FEATURE = ATA_REG_ERR,
+ ATA_REG_CMD = ATA_REG_STATUS,
+ ATA_REG_BYTEL = ATA_REG_LBAM,
+ ATA_REG_BYTEH = ATA_REG_LBAH,
+ ATA_REG_DEVSEL = ATA_REG_DEVICE,
+ ATA_REG_IRQ = ATA_REG_NSECT,
+};
- /* SETFEATURES stuff */
+/* SETFEATURES stuff */
+enum ata_set_features{
SETFEATURES_XFER = 0x03,
XFER_UDMA_7 = 0x47,
XFER_UDMA_6 = 0x46,
@@ -130,9 +132,13 @@
XFER_UDMA_2 = 0x42,
XFER_UDMA_1 = 0x41,
XFER_UDMA_0 = 0x40,
+ XFER_MW_DMA_4 = 0x24, /* CFA only */
+ XFER_MW_DMA_3 = 0x23, /* CFA only */
XFER_MW_DMA_2 = 0x22,
XFER_MW_DMA_1 = 0x21,
XFER_MW_DMA_0 = 0x20,
+ XFER_PIO_6 = 0x0E, /* CFA only */
+ XFER_PIO_5 = 0x0D, /* CFA only */
XFER_PIO_4 = 0x0C,
XFER_PIO_3 = 0x0B,
XFER_PIO_2 = 0x0A,
@@ -141,8 +147,14 @@
XFER_SW_DMA_2 = 0x12,
XFER_SW_DMA_1 = 0x11,
XFER_SW_DMA_0 = 0x10,
- XFER_PIO_SLOW = 0x00
+ XFER_PIO_SLOW = 0x00,
+
+ SETFEATURES_WC_ON = 0x02, /* Enable write cache */
+ SETFEATURES_WC_OFF = 0x82, /* Disable write cache */
+
+ SETFEATURES_SPINUP = 0x07, /* Spin-up drive */
};
+
/*
* ATA Commands (only mandatory commands listed here)
*/
--- work/include/libata.h 2008-03-19 08:49:47.000000000 +0100
+++ u-boot/include/libata.h 2008-03-18 11:56:02.000000000 +0100
@@ -47,38 +47,6 @@
ATA_CMD_WRITE_FPDMA_QUEUED = 0x61,
};
-/* SETFEATURES stuff
- */
-enum ata_set_features {
- /* SETFEATURES stuff */
- SETFEATURES_XFER = 0x03,
- XFER_UDMA_7 = 0x47,
- XFER_UDMA_6 = 0x46,
- XFER_UDMA_5 = 0x45,
- XFER_UDMA_4 = 0x44,
- XFER_UDMA_3 = 0x43,
- XFER_UDMA_2 = 0x42,
- XFER_UDMA_1 = 0x41,
- XFER_UDMA_0 = 0x40,
- XFER_MW_DMA_4 = 0x24, /* CFA only */
- XFER_MW_DMA_3 = 0x23, /* CFA only */
- XFER_MW_DMA_2 = 0x22,
- XFER_MW_DMA_1 = 0x21,
- XFER_MW_DMA_0 = 0x20,
- XFER_PIO_6 = 0x0E, /* CFA only */
- XFER_PIO_5 = 0x0D, /* CFA only */
- XFER_PIO_4 = 0x0C,
- XFER_PIO_3 = 0x0B,
- XFER_PIO_2 = 0x0A,
- XFER_PIO_1 = 0x09,
- XFER_PIO_0 = 0x08,
- XFER_PIO_SLOW = 0x00,
-
- SETFEATURES_WC_ON = 0x02, /* Enable write cache */
- SETFEATURES_WC_OFF = 0x82, /* Disable write cache */
-
- SETFEATURES_SPINUP = 0x07, /* Spin-up drive */
-};
enum ata_protocol {
ATA_PROT_UNKNOWN, /* unknown */
@@ -99,27 +67,10 @@
};
enum {
- ATA_SECT_SIZE = 512,
ATA_MAX_SECTORS_128 = 128,
ATA_MAX_SECTORS = 256,
ATA_MAX_SECTORS_LBA48 = 65535,
- /* bits in ATA command block registers */
- ATA_HOB = (1 << 7), /* LBA48 selector */
- ATA_NIEN = (1 << 1), /* disable-irq flag */
- ATA_LBA = (1 << 6), /* LBA28 selector */
- ATA_DEV1 = (1 << 4), /* Select Device 1 (slave) */
- ATA_BUSY = (1 << 7), /* BSY status bit */
- ATA_DRDY = (1 << 6), /* device ready */
- ATA_DF = (1 << 5), /* device fault */
- ATA_DRQ = (1 << 3), /* data request i/o */
- ATA_ERR = (1 << 0), /* have an error */
- ATA_SRST = (1 << 2), /* software reset */
- ATA_ICRC = (1 << 7), /* interface CRC error */
- ATA_UNC = (1 << 6), /* uncorrectable media error */
- ATA_IDNF = (1 << 4), /* ID not found */
- ATA_ABORTED = (1 << 2), /* command aborted */
-
ATA_ID_WORDS = 256,
ATA_ID_SERNO = 10,
ATA_ID_FW_REV = 23,
@@ -193,5 +144,5 @@
}
int sata_init(void);
-
+void ata_dump_id(u16 *id);
#endif /* __LIBATA_H__ */
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
U-Boot-Users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/u-boot-users
