I just ran into a problem with current U-Boot on Kilauea and device tree enabled Linux kernel (arch/powerpc). After updating U-Boot the kernel doesn't boot anymore:
=> run net_nfs_fdt Waiting for PHY auto negotiation to complete... done ENET Speed is 1000 Mbps - FULL duplex connection (EMAC0) Using ppc_4xx_eth0 device TFTP from server 10.0.0.152; our IP address is 10.0.0.182 Filename 'kilauea/uImage'. Load address: 0x200000 Loading: ################################################################# ####################### done Bytes transferred = 1288707 (13aa03 hex) ENET Speed is 1000 Mbps - FULL duplex connection (EMAC0) Using ppc_4xx_eth0 device TFTP from server 10.0.0.152; our IP address is 10.0.0.182 Filename 'kilauea/kilauea.dtb'. Load address: 0x400000 Loading: # done Bytes transferred = 8000 (1f40 hex) ## Booting kernel from Legacy Image at 00200000 ... Image Name: Linux-2.6.25-rc7-next-20080327-d Created: 2008-03-27 13:51:18 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1288643 Bytes = 1.2 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK ERROR: image overwritten - must RESET the board to recover. Before updating U-Boot I am able to boot exactly this kernel/dtb combination without problems: => run net_nfs_fdt Waiting for PHY auto negotiation to complete... done ENET Speed is 1000 Mbps - FULL duplex connection (EMAC0) Using ppc_4xx_eth0 device TFTP from server 10.0.0.152; our IP address is 10.0.0.182 Filename 'kilauea/uImage'. Load address: 0x200000 Loading: ################################################################# ####################### done Bytes transferred = 1288707 (13aa03 hex) ENET Speed is 1000 Mbps - FULL duplex connection (EMAC0) Using ppc_4xx_eth0 device TFTP from server 10.0.0.152; our IP address is 10.0.0.182 Filename 'kilauea/kilauea.dtb'. Load address: 0x400000 Loading: # done Bytes transferred = 8000 (1f40 hex) ## Booting image at 00200000 ... Image Name: Linux-2.6.25-rc7-next-20080327-d Created: 2008-03-27 13:51:18 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1288643 Bytes = 1.2 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Booting using the fdt at 0x400000 Using Kilauea machine description ... Any ideas? Best regards, Stefan ===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: [EMAIL PROTECTED] ===================================================================== ------------------------------------------------------------------------- Check out the new SourceForge.net Marketplace. It's the best place to buy or sell services for just about anything Open Source. http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace _______________________________________________ U-Boot-Users mailing list U-Boot-Users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/u-boot-users