From: Heiko Schocher <h...@denx.de>
s_init has the same outline for all the AM33xx based
board. So making it generic.
This also helps in addition of new Soc with minimal changes.
Signed-off-by: Lokesh Vutla <lokeshvu...@ti.com>
Signed-off-by: Heiko Schocher <h...@denx.de>
Signed-off-by: Tom Rini <tr...@ti.com>
---
arch/arm/cpu/armv7/am33xx/board.c | 46 +++++++++++++--
arch/arm/cpu/armv7/am33xx/clock_ti814x.c | 6 ++
arch/arm/cpu/armv7/am33xx/emif4.c | 6 +-
arch/arm/include/asm/arch-am33xx/clocks_am33xx.h | 6 +-
arch/arm/include/asm/arch-am33xx/sys_proto.h | 5 +-
board/isee/igep0033/board.c | 49 +++-------------
board/phytec/pcm051/board.c | 48 +++-------------
board/ti/am335x/board.c | 52 +++--------------
board/ti/ti814x/evm.c | 67 +++-------------------
9 files changed, 90 insertions(+), 195 deletions(-)
diff --git a/arch/arm/cpu/armv7/am33xx/board.c
b/arch/arm/cpu/armv7/am33xx/board.c
index 1d743d6..3d08673 100644
--- a/arch/arm/cpu/armv7/am33xx/board.c
+++ b/arch/arm/cpu/armv7/am33xx/board.c
@@ -145,7 +145,7 @@ int arch_misc_init(void)
}
#ifdef CONFIG_SPL_BUILD
-void rtc32k_enable(void)
+static void rtc32k_enable(void)
{
struct rtc_regs *rtc = (struct rtc_regs *)RTC_BASE;
@@ -161,11 +161,7 @@ void rtc32k_enable(void)
writel((1 << 3) | (1 << 6), &rtc->osc);
}
-#define UART_RESET (0x1 << 1)
-#define UART_CLK_RUNNING_MASK 0x1
-#define UART_SMART_IDLE_EN (0x1 << 0x3)
-
-void uart_soft_reset(void)
+static void uart_soft_reset(void)
{
struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE;
u32 regval;
@@ -182,4 +178,42 @@ void uart_soft_reset(void)
regval |= UART_SMART_IDLE_EN;
writel(regval, &uart_base->uartsyscfg);
}
+
+static void watchdog_disable(void)
+{
+ struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
+
+ writel(0xAAAA, &wdtimer->wdtwspr);
+ while (readl(&wdtimer->wdtwwps) != 0x0)
+ ;
+ writel(0x5555, &wdtimer->wdtwspr);
+ while (readl(&wdtimer->wdtwwps) != 0x0)
+ ;
+}
#endif
+
+void s_init(void)
+{
+ /*
+ * Save the boot parameters passed from romcode.
+ * We cannot delay the saving further than this,
+ * to prevent overwrites.
+ */
+#ifdef CONFIG_SPL_BUILD
+ save_omap_boot_params();
+ watchdog_disable();
+ timer_init();
+ set_uart_mux_conf();
+ setup_clocks_for_console();
+ uart_soft_reset();
+
+ gd = &gdata;
+ preloader_console_init();
+
+ prcm_init();
+ set_mux_conf_regs();
+ /* Enable RTC32K clock */
+ rtc32k_enable();
+ sdram_init();
+#endif
+}
diff --git a/arch/arm/cpu/armv7/am33xx/clock_ti814x.c
b/arch/arm/cpu/armv7/am33xx/clock_ti814x.c
index 1a23746..ca7d7ad 100644
--- a/arch/arm/cpu/armv7/am33xx/clock_ti814x.c
+++ b/arch/arm/cpu/armv7/am33xx/clock_ti814x.c
@@ -285,6 +285,12 @@ static void enable_per_clocks(void)
writel(PRCM_MOD_EN, &cmalwon->ethernet1clkctrl);
while ((readl(&cmalwon->ethernet1clkctrl) & ENET_CLKCTRL_CMPL) != 0)
;
+
+ /* RTC clocks */
+ writel(PRCM_MOD_EN, &cmalwon->rtcclkstctrl);
+ writel(PRCM_MOD_EN, &cmalwon->rtcclkctrl);
+ while (readl(&cmalwon->rtcclkctrl) != PRCM_MOD_EN)
+ ;
}
/*
diff --git a/arch/arm/cpu/armv7/am33xx/emif4.c
b/arch/arm/cpu/armv7/am33xx/emif4.c
index 47d3dee..3abb609 100644
--- a/arch/arm/cpu/armv7/am33xx/emif4.c
+++ b/arch/arm/cpu/armv7/am33xx/emif4.c
@@ -44,8 +44,6 @@ void dram_init_banksize(void)
#ifdef CONFIG_SPL_BUILD
-static struct dmm_lisa_map_regs *hw_lisa_map_regs =
- (struct dmm_lisa_map_regs *)DMM_BASE;
static struct vtp_reg *vtpreg[2] = {
(struct vtp_reg *)VTP0_CTRL_ADDR,
(struct vtp_reg *)VTP1_CTRL_ADDR};
@@ -53,6 +51,9 @@ static struct vtp_reg *vtpreg[2] = {
static struct ddr_ctrl *ddrctrl = (struct ddr_ctrl *)DDR_CTRL_ADDR;
#endif
+#ifdef CONFIG_TI81XX
+static struct dmm_lisa_map_regs *hw_lisa_map_regs =
+ (struct dmm_lisa_map_regs *)DMM_BASE;
void config_dmm(const struct dmm_lisa_map_regs *regs)
{
enable_dmm_clocks();
@@ -67,6 +68,7 @@ void config_dmm(const struct dmm_lisa_map_regs *regs)
writel(regs->dmm_lisa_map_1, &hw_lisa_map_regs->dmm_lisa_map_1);
writel(regs->dmm_lisa_map_0, &hw_lisa_map_regs->dmm_lisa_map_0);
}
+#endif
static void config_vtp(int nr)
{
diff --git a/arch/arm/include/asm/arch-am33xx/clocks_am33xx.h
b/arch/arm/include/asm/arch-am33xx/clocks_am33xx.h
index 89b63d9..dc49e7e 100644
--- a/arch/arm/include/asm/arch-am33xx/clocks_am33xx.h
+++ b/arch/arm/include/asm/arch-am33xx/clocks_am33xx.h
@@ -24,8 +24,10 @@
#define CONFIG_SYS_MPUCLK 550
#endif
-extern void pll_init(void);
-extern void enable_emif_clocks(void);
+#define UART_RESET (0x1 << 1)
+#define UART_CLK_RUNNING_MASK 0x1
+#define UART_SMART_IDLE_EN (0x1 << 0x3)
+
extern void enable_dmm_clocks(void);
#endif /* endif _CLOCKS_AM33XX_H_ */
diff --git a/arch/arm/include/asm/arch-am33xx/sys_proto.h
b/arch/arm/include/asm/arch-am33xx/sys_proto.h
index 04b8561..4efa1c2 100644
--- a/arch/arm/include/asm/arch-am33xx/sys_proto.h
+++ b/arch/arm/include/asm/arch-am33xx/sys_proto.h
@@ -43,7 +43,8 @@ void enable_gpmc_cs_config(const u32 *gpmc_config, struct
gpmc_cs *cs, u32 base,
u32 size);
void omap_nand_switch_ecc(uint32_t, uint32_t);
-void rtc32k_enable(void);
-void uart_soft_reset(void);
+void set_uart_mux_conf(void);
+void set_mux_conf_regs(void);
+void sdram_init(void);
u32 wait_on_value(u32, u32, void *, u32);
#endif
diff --git a/board/isee/igep0033/board.c b/board/isee/igep0033/board.c
index fe80084..809448f 100644
--- a/board/isee/igep0033/board.c
+++ b/board/isee/igep0033/board.c
@@ -35,8 +35,6 @@
DECLARE_GLOBAL_DATA_PTR;
-static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
-
/* MII mode defines */
#define RMII_MODE_ENABLE 0x4D
@@ -74,54 +72,23 @@ static struct emif_regs ddr3_emif_reg_data = {
.zq_config = K4B2G1646EBIH9_ZQ_CFG,
.emif_ddr_phy_ctlr_1 = K4B2G1646EBIH9_EMIF_READ_LATENCY,
};
-#endif
-/*
- * Early system init of muxing and clocks.
- */
-void s_init(void)
+void set_uart_mux_conf(void)
{
- /*
- * Save the boot parameters passed from romcode.
- * We cannot delay the saving further than this,
- * to prevent overwrites.
- */
-#ifdef CONFIG_SPL_BUILD
- save_omap_boot_params();
-#endif
-
- /* WDT1 is already running when the bootloader gets control
- * Disable it to avoid "random" resets
- */
- writel(0xAAAA, &wdtimer->wdtwspr);
- while (readl(&wdtimer->wdtwwps) != 0x0)
- ;
- writel(0x5555, &wdtimer->wdtwspr);
- while (readl(&wdtimer->wdtwwps) != 0x0)
- ;
-
-#ifdef CONFIG_SPL_BUILD
- setup_clocks_for_console();
-
enable_uart0_pin_mux();
+}
- uart_soft_reset();
- gd = &gdata;
-
- preloader_console_init();
-
- prcm_init();
-
- /* Enable RTC32K clock */
- rtc32k_enable();
-
- /* Configure board pin mux */
+void set_mux_conf_regs(void)
+{
enable_board_pin_mux();
+}
+void sdram_init(void)
+{
config_ddr(303, K4B2G1646EBIH9_IOCTRL_VALUE, &ddr3_data,
&ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
-#endif
}
+#endif
/*
* Basic board specific setup. Pinmux has been handled already.
diff --git a/board/phytec/pcm051/board.c b/board/phytec/pcm051/board.c
index 0cca8d7..0d6a64c 100644
--- a/board/phytec/pcm051/board.c
+++ b/board/phytec/pcm051/board.c
@@ -38,8 +38,6 @@
DECLARE_GLOBAL_DATA_PTR;
-static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
-
/* MII mode defines */
#define MII_MODE_ENABLE 0x0
#define RGMII_MODE_ENABLE 0xA
@@ -84,57 +82,27 @@ static struct emif_regs ddr3_emif_reg_data = {
.emif_ddr_phy_ctlr_1 = MT41J256M8HX15E_EMIF_READ_LATENCY |
PHY_EN_DYN_PWRDN,
};
-#endif
-/*
- * early system init of muxing and clocks.
- */
-void s_init(void)
+void set_uart_mux_conf(void)
{
- /*
- * Save the boot parameters passed from romcode.
- * We cannot delay the saving further than this,
- * to prevent overwrites.
- */
-#ifdef CONFIG_SPL_BUILD
- save_omap_boot_params();
-#endif
-
- /*
- * WDT1 is already running when the bootloader gets control
- * Disable it to avoid "random" resets
- */
- writel(0xAAAA, &wdtimer->wdtwspr);
- while (readl(&wdtimer->wdtwwps) != 0x0)
- ;
- writel(0x5555, &wdtimer->wdtwspr);
- while (readl(&wdtimer->wdtwwps) != 0x0)
- ;
-
-#ifdef CONFIG_SPL_BUILD
- /* Setup the PLLs and the clocks for the peripherals */
- pll_init();
-
- /* Enable RTC32K clock */
- rtc32k_enable();
-
enable_uart0_pin_mux();
- uart_soft_reset();
-
- gd = &gdata;
-
- preloader_console_init();
+}
+void set_mux_conf_regs(void)
+{
/* Initalize the board header */
enable_i2c0_pin_mux();
i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
enable_board_pin_mux();
+}
+void sdram_init(void)
+{
config_ddr(DDR_CLK_MHZ, MT41J256M8HX15E_IOCTRL_VALUE, &ddr3_data,
&ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
-#endif
}
+#endif
/*
* Basic board specific setup. Pinmux has been handled already.
diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c
index bebfa60..3b50dd0 100644
--- a/board/ti/am335x/board.c
+++ b/board/ti/am335x/board.c
@@ -37,8 +37,6 @@
DECLARE_GLOBAL_DATA_PTR;
-static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
-
/* MII mode defines */
#define MII_MODE_ENABLE 0x0
#define RGMII_MODE_ENABLE 0x3A
@@ -282,36 +280,8 @@ int spl_start_uboot(void)
}
#endif
-#endif
-
-/*
- * early system init of muxing and clocks.
- */
-void s_init(void)
+void set_uart_mux_conf(void)
{
- /*
- * Save the boot parameters passed from romcode.
- * We cannot delay the saving further than this,
- * to prevent overwrites.
- */
-#ifdef CONFIG_SPL_BUILD
- save_omap_boot_params();
-#endif
-
- /* WDT1 is already running when the bootloader gets control
- * Disable it to avoid "random" resets
- */
- writel(0xAAAA, &wdtimer->wdtwspr);
- while (readl(&wdtimer->wdtwwps) != 0x0)
- ;
- writel(0x5555, &wdtimer->wdtwspr);
- while (readl(&wdtimer->wdtwwps) != 0x0)
- ;
-
-#ifdef CONFIG_SPL_BUILD
- /* Setup the PLLs and the clocks for the peripherals */
- setup_clocks_for_console();
-
#ifdef CONFIG_SERIAL1
enable_uart0_pin_mux();
#endif /* CONFIG_SERIAL1 */
@@ -330,25 +300,21 @@ void s_init(void)
#ifdef CONFIG_SERIAL6
enable_uart5_pin_mux();
#endif /* CONFIG_SERIAL6 */
+}
- uart_soft_reset();
-
- gd = &gdata;
-
- preloader_console_init();
-
- prcm_init();
-
+void set_mux_conf_regs(void)
+{
/* Initalize the board header */
enable_i2c0_pin_mux();
i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
if (read_eeprom() < 0)
puts("Could not get board ID.\n");
- /* Enable RTC32K clock */
- rtc32k_enable();
-
enable_board_pin_mux(&header);
+}
+
+void sdram_init(void)
+{
if (board_is_evm_sk()) {
/*
* EVM SK 1.2A and later use gpio0_7 to enable DDR3.
@@ -372,8 +338,8 @@ void s_init(void)
else
config_ddr(266, MT47H128M16RT25E_IOCTRL_VALUE, &ddr2_data,
&ddr2_cmd_ctrl_data, &ddr2_emif_reg_data, 0);
-#endif
}
+#endif
/*
* Basic board specific setup. Pinmux has been handled already.
diff --git a/board/ti/ti814x/evm.c b/board/ti/ti814x/evm.c
index 704fdf4..28d2561 100644
--- a/board/ti/ti814x/evm.c
+++ b/board/ti/ti814x/evm.c
@@ -35,30 +35,10 @@
DECLARE_GLOBAL_DATA_PTR;
-#ifdef CONFIG_SPL_BUILD
-static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
-#endif
-
static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
/* UART Defines */
#ifdef CONFIG_SPL_BUILD
-static void uart_enable(void)
-{
- /* UART softreset */
- uart_soft_reset();
-}
-
-static void wdt_disable(void)
-{
- writel(0xAAAA, &wdtimer->wdtwspr);
- while (readl(&wdtimer->wdtwwps) != 0x0)
- ;
- writel(0x5555, &wdtimer->wdtwspr);
- while (readl(&wdtimer->wdtwwps) != 0x0)
- ;
-}
-
static const struct cmd_control evm_ddr2_cctrl_data = {
.cmd0csratio = 0x80,
.cmd0dldiff = 0x04,
@@ -108,63 +88,32 @@ static const struct ddr_data evm_ddr2_data = {
.datauserank0delay = 1,
.datadldiff0 = 0x4,
};
-#endif
-/*
- * early system init of muxing and clocks.
- */
-void s_init(void)
+void set_uart_mux_conf(void)
{
-#ifdef CONFIG_SPL_BUILD
- /*
- * Save the boot parameters passed from romcode.
- * We cannot delay the saving further than this,
- * to prevent overwrites.
- */
-#ifdef CONFIG_SPL_BUILD
- save_omap_boot_params();
-#endif
-
- /* WDT1 is already running when the bootloader gets control
- * Disable it to avoid "random" resets
- */
- wdt_disable();
-
- /* Enable timer */
- timer_init();
-
- setup_clocks_for_console();
-
/* Set UART pins */
enable_uart0_pin_mux();
+}
+void set_mux_conf_regs(void)
+{
/* Set MMC pins */
enable_mmc1_pin_mux();
/* Set Ethernet pins */
enable_enet_pin_mux();
+}
- /* Enable UART */
- uart_enable();
-
- gd = &gdata;
-
- preloader_console_init();
-
- /* Setup the PLLs and the clocks for the peripherals */
- prcm_init();
-
- /* Enable RTC32K clock */
- rtc32k_enable();
-
+void sdram_init(void)
+{
config_dmm(&evm_lisa_map_regs);
config_ddr(0, 0, &evm_ddr2_data, &evm_ddr2_cctrl_data,
&evm_ddr2_emif0_regs, 0);
config_ddr(0, 0, &evm_ddr2_data, &evm_ddr2_cctrl_data,
&evm_ddr2_emif1_regs, 1);
-#endif
}
+#endif
/*
* Basic board specific setup. Pinmux has been handled already.
--
1.7.9.5
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
