Hi Heiko,
On Tuesday 25 June 2013 10:24 AM, Heiko Schocher wrote:
Hello Lokesh,
Am 25.06.2013 05:48, schrieb Lokesh Vutla:
Hi Heiko,
On Tuesday 25 June 2013 12:42 AM, Heiko Schocher wrote:
Hello Lokesh,
Am 24.06.2013 15:15, schrieb Lokesh Vutla:
Locking sequence for all the dplls is same.
In the current code same sequence is done repeatedly
for each dpll. Instead have a generic function
for locking dplls and pass dpll data to that function.
This is derived from OMAP4 boards.
Signed-off-by: Lokesh Vutla <lokeshvu...@ti.com>
---
arch/arm/cpu/armv7/am33xx/Makefile | 1 +
arch/arm/cpu/armv7/am33xx/clock.c | 116 ++++++++++++++
arch/arm/cpu/armv7/am33xx/clock_am33xx.c | 222
+++++---------------------
arch/arm/cpu/armv7/am33xx/emif4.c | 4 +
arch/arm/include/asm/arch-am33xx/clock.h | 68 ++++++++
arch/arm/include/asm/arch-am33xx/ddr_defs.h | 2 +
arch/arm/include/asm/arch-am33xx/sys_proto.h | 1 +
7 files changed, 232 insertions(+), 182 deletions(-)
create mode 100644 arch/arm/cpu/armv7/am33xx/clock.c
[...]
diff --git a/arch/arm/cpu/armv7/am33xx/clock.c
b/arch/arm/cpu/armv7/am33xx/clock.c
new file mode 100644
index 0000000..a7f1d83
--- /dev/null
+++ b/arch/arm/cpu/armv7/am33xx/clock.c
@@ -0,0 +1,116 @@
[...]
+static void do_setup_dpll(const struct dpll_regs *dpll_regs,
+ const struct dpll_params *params)
+{
Could we have this function not only static? I posted a patch:
[U-Boot] arm, am335x: make mpu pll config configurable
http://patchwork.ozlabs.org/patch/248509/
which uses mpu_pll_config() for switching mpu pll clock
from board code ... you delete this function later in this patch,
so I think, I can switch to do_setup_pll() ... if this is not
static code ...
Yes I saw that patch. No need to make this non-static.
Please have your own struct "const struct dpll_params dpll_mpu"
and update your values accordingly.
Hmm.. maybe I miss something here. You call setup_dplls()
in arch/arm/cpu/armv7/am33xx/clock.c using &dpll_mpu defined
in arch/arm/cpu/armv7/am33xx/clock_am33xx.c ... so how to
make here a board specific struct?
The MPUCLK is configurable through the define CONFIG_SYS_MPUCLK
which is good, but I have on this board a PMIC, which in board SPL
code change MPU and core voltage ... and after that I change
the MPU clock again ...
Ohk.
Can't we scale the voltages before calling setup_dplls()
(Why do you want to configure the MPU clocks twice?
I don't know much about your board, so I am just asking..:) )
What I meant is something like below:
void __weak scale_vcores(void)
{}
void prcm_init()
{
enable_basic_clocks();
scale_vcores();
setup_dplls();
}
have your own scale_vcores in your board file.
and for dpll_mpu have something like this:
#ifdef CONFIG_<BOARD>
const struct dpll_params dpll_mpu = {
M, N, 1, -1, -1, -1, -1};
#else
const struct dpll_params dpll_mpu = {
CONFIG_SYS_MPUCLK, OSC-1, 1, -1, -1, -1, -1};
#endif
I hope this should be possible on your board.
I am telling this because it will be easy for me during my next cleanup
during
which I planned to combine omap-common and am33xx code..:)
This is the exactly what is done for omap( program voltages and then
setup dplls)
You can refer to arch/arm/cpu/armv7/omap-common/clocks-common.c
prcm_init() function.
Please correct me if I am wrong..
Thanks and regards,
Lokesh
bye,
Heiko
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
