MXC SPI driver has a feature whereas a GPIO line can be used as a CS signal. This is set up by joining the CS and GPIO values into a single value using (cs | gpio << 8), and passing it off as a CS value. This breaks the sf probe command, because it is no longer possible to invoke it as sf probe <cs>. Instead, the user must use sf probe <cs | gpio << 8>.
Fix this by introducing a new board function: board_spi_cs_gpio(). When called, board_spi_cs_gpio() will return the gpio number for the cs value it is given. Cc: Jagannadha Sutradharudu Teki <[email protected]> Cc: Eric Nelson <[email protected]> Cc: Eric Benard <[email protected]> Cc: Fabio Estevam <[email protected]> Cc: Tim Harvey <[email protected]> Cc: Stefano Babic <[email protected]> Cc: Tom Rini <[email protected]> Signed-off-by: Nikita Kiryanov <[email protected]> --- board/boundary/nitrogen6x/nitrogen6x.c | 5 +++ board/embest/mx6boards/mx6boards.c | 5 +++ board/freescale/mx6qsabreauto/mx6qsabreauto.c | 7 ++++ board/freescale/mx6sabresd/mx6sabresd.c | 7 ++++ board/freescale/mx6slevk/mx6slevk.c | 5 +++ board/gateworks/gw_ventana/gw_ventana.c | 7 +++- board/genesi/mx51_efikamx/efikamx.c | 5 +++ board/ttcontrol/vision2/vision2.c | 5 +++ drivers/spi/mxc_spi.c | 48 ++++++++++++++------------- include/configs/embestmx6boards.h | 2 +- include/configs/gw_ventana.h | 2 +- include/configs/mx51_efikamx.h | 4 +-- include/configs/mx6sabre_common.h | 2 +- include/configs/mx6slevk.h | 2 +- include/configs/nitrogen6x.h | 2 +- include/configs/vision2.h | 4 +-- 16 files changed, 79 insertions(+), 33 deletions(-) diff --git a/board/boundary/nitrogen6x/nitrogen6x.c b/board/boundary/nitrogen6x/nitrogen6x.c index 84294db..aadddb9 100644 --- a/board/boundary/nitrogen6x/nitrogen6x.c +++ b/board/boundary/nitrogen6x/nitrogen6x.c @@ -328,6 +328,11 @@ int board_mmc_init(bd_t *bis) #endif #ifdef CONFIG_MXC_SPI +int board_spi_cs_gpio(unsigned bus, unsigned cs) +{ + return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(3, 19)) : -1; +} + iomux_v3_cfg_t const ecspi1_pads[] = { /* SS1 */ MX6_PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL), diff --git a/board/embest/mx6boards/mx6boards.c b/board/embest/mx6boards/mx6boards.c index d06b57d..e8a11c2 100644 --- a/board/embest/mx6boards/mx6boards.c +++ b/board/embest/mx6boards/mx6boards.c @@ -284,6 +284,11 @@ iomux_v3_cfg_t const ecspi1_pads[] = { MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL), }; +int board_spi_cs_gpio(unsigned bus, unsigned cs) +{ + return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(2, 30)) : -1; +} + static void setup_spi(void) { imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads)); diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c b/board/freescale/mx6qsabreauto/mx6qsabreauto.c index 928dadf..836d722 100644 --- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c +++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c @@ -259,6 +259,13 @@ int board_init(void) return 0; } +#ifdef CONFIG_MXC_SPI +int board_spi_cs_gpio(unsigned bus, unsigned cs) +{ + return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(4, 9)) : -1; +} +#endif + #ifdef CONFIG_CMD_BMODE static const struct boot_mode board_boot_modes[] = { /* 4 bit bus width */ diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c index d7c4b4f..c5f10f7 100644 --- a/board/freescale/mx6sabresd/mx6sabresd.c +++ b/board/freescale/mx6sabresd/mx6sabresd.c @@ -513,6 +513,13 @@ static int pfuze_init(void) return 0; } +#ifdef CONFIG_MXC_SPI +int board_spi_cs_gpio(unsigned bus, unsigned cs) +{ + return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(4, 9)) : -1; +} +#endif + #ifdef CONFIG_CMD_BMODE static const struct boot_mode board_boot_modes[] = { /* 4 bit bus width */ diff --git a/board/freescale/mx6slevk/mx6slevk.c b/board/freescale/mx6slevk/mx6slevk.c index d2b64cc..ec63d9e 100644 --- a/board/freescale/mx6slevk/mx6slevk.c +++ b/board/freescale/mx6slevk/mx6slevk.c @@ -82,6 +82,11 @@ static iomux_v3_cfg_t ecspi1_pads[] = { MX6_PAD_ECSPI1_SS0__GPIO4_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL), }; +int board_spi_cs_gpio(unsigned bus, unsigned cs) +{ + return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(4, 11)) : -1; +} + static void setup_spi(void) { imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads)); diff --git a/board/gateworks/gw_ventana/gw_ventana.c b/board/gateworks/gw_ventana/gw_ventana.c index 9d2651f..054f904 100644 --- a/board/gateworks/gw_ventana/gw_ventana.c +++ b/board/gateworks/gw_ventana/gw_ventana.c @@ -353,9 +353,14 @@ iomux_v3_cfg_t const ecspi1_pads[] = { IOMUX_PADS(PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL)), }; +int board_spi_cs_gpio(unsigned bus, unsigned cs) +{ + return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(3, 19)) : -1; +} + static void setup_spi(void) { - gpio_direction_output(CONFIG_SF_DEFAULT_CS, 1); + gpio_direction_output(IMX_GPIO_NR(3, 19), 1); SETUP_IOMUX_PADS(ecspi1_pads); } #endif diff --git a/board/genesi/mx51_efikamx/efikamx.c b/board/genesi/mx51_efikamx/efikamx.c index 16769e5..137e4ed 100644 --- a/board/genesi/mx51_efikamx/efikamx.c +++ b/board/genesi/mx51_efikamx/efikamx.c @@ -152,6 +152,11 @@ static iomux_v3_cfg_t const efikamx_spi_pads[] = { * PMIC configuration */ #ifdef CONFIG_MXC_SPI +int board_spi_cs_gpio(unsigned bus, unsigned cs) +{ + return (bus == 0 && cs == 1) ? 121 : -1; +} + static void power_init(void) { unsigned int val; diff --git a/board/ttcontrol/vision2/vision2.c b/board/ttcontrol/vision2/vision2.c index b4d3994..b5249e7 100644 --- a/board/ttcontrol/vision2/vision2.c +++ b/board/ttcontrol/vision2/vision2.c @@ -144,6 +144,11 @@ static void setup_uart(void) } #ifdef CONFIG_MXC_SPI +int board_spi_cs_gpio(unsigned bus, unsigned cs) +{ + return (bus == 0 && cs == 1) ? 121 : -1; +} + void spi_io_init(void) { static const iomux_v3_cfg_t spi_pads[] = { diff --git a/drivers/spi/mxc_spi.c b/drivers/spi/mxc_spi.c index f3f029d..9583ef0 100644 --- a/drivers/spi/mxc_spi.c +++ b/drivers/spi/mxc_spi.c @@ -25,6 +25,11 @@ static unsigned long spi_bases[] = { MXC_SPI_BASE_ADDRESSES }; +__weak int board_spi_cs_gpio(unsigned bus, unsigned cs) +{ + return -1; +} + #define OUT MXC_GPIO_DIRECTION_OUT #define reg_read readl @@ -358,31 +363,30 @@ void spi_init(void) { } -static int decode_cs(struct mxc_spi_slave *mxcs, unsigned int cs) +/* + * Some SPI devices require active chip-select over multiple + * transactions, we achieve this using a GPIO. Still, the SPI + * controller has to be configured to use one of its own chipselects. + * To use this feature you have to implement board_spi_cs_gpio() to assign + * a gpio value for each cs (-1 if cs doesn't need to use gpio). + * You must use some unused on this SPI controller cs between 0 and 3. + */ +static int setup_cs_gpio(struct mxc_spi_slave *mxcs, + unsigned int bus, unsigned int cs) { int ret; - /* - * Some SPI devices require active chip-select over multiple - * transactions, we achieve this using a GPIO. Still, the SPI - * controller has to be configured to use one of its own chipselects. - * To use this feature you have to call spi_setup_slave() with - * cs = internal_cs | (gpio << 8), and you have to use some unused - * on this SPI controller cs between 0 and 3. - */ - if (cs > 3) { - mxcs->gpio = cs >> 8; - cs &= 3; - ret = gpio_direction_output(mxcs->gpio, !(mxcs->ss_pol)); - if (ret) { - printf("mxc_spi: cannot setup gpio %d\n", mxcs->gpio); - return -EINVAL; - } - } else { - mxcs->gpio = -1; + mxcs->gpio = board_spi_cs_gpio(bus, cs); + if (mxcs->gpio == -1) + return 0; + + ret = gpio_direction_output(mxcs->gpio, !(mxcs->ss_pol)); + if (ret) { + printf("mxc_spi: cannot setup gpio %d\n", mxcs->gpio); + return -EINVAL; } - return cs; + return 0; } struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, @@ -402,14 +406,12 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, mxcs->ss_pol = (mode & SPI_CS_HIGH) ? 1 : 0; - ret = decode_cs(mxcs, cs); + ret = setup_cs_gpio(mxcs, bus, cs); if (ret < 0) { free(mxcs); return NULL; } - cs = ret; - mxcs->base = spi_bases[bus]; ret = spi_cfg_mxc(mxcs, cs, max_hz, mode); diff --git a/include/configs/embestmx6boards.h b/include/configs/embestmx6boards.h index f1000f3..bcd5ea4 100644 --- a/include/configs/embestmx6boards.h +++ b/include/configs/embestmx6boards.h @@ -100,7 +100,7 @@ #define CONFIG_SPI_FLASH_SST #define CONFIG_MXC_SPI #define CONFIG_SF_DEFAULT_BUS 0 -#define CONFIG_SF_DEFAULT_CS (0 | (IMX_GPIO_NR(2, 30) << 8)) +#define CONFIG_SF_DEFAULT_CS 0 #define CONFIG_SF_DEFAULT_SPEED 20000000 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 #endif diff --git a/include/configs/gw_ventana.h b/include/configs/gw_ventana.h index 8197a72..97398a8 100644 --- a/include/configs/gw_ventana.h +++ b/include/configs/gw_ventana.h @@ -61,7 +61,7 @@ #define CONFIG_SPI_FLASH_BAR #define CONFIG_SPI_FLASH_WINBOND #define CONFIG_SF_DEFAULT_BUS 0 - #define CONFIG_SF_DEFAULT_CS (0|(IMX_GPIO_NR(3, 19)<<8)) + #define CONFIG_SF_DEFAULT_CS 0 /* GPIO 3-19 (21248) */ #define CONFIG_SF_DEFAULT_SPEED 30000000 #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0) diff --git a/include/configs/mx51_efikamx.h b/include/configs/mx51_efikamx.h index 0f2a4ef..fce7ead 100644 --- a/include/configs/mx51_efikamx.h +++ b/include/configs/mx51_efikamx.h @@ -96,11 +96,11 @@ #define CONFIG_SPI_FLASH #define CONFIG_SPI_FLASH_SST -#define CONFIG_SF_DEFAULT_CS (1 | 121 << 8) +#define CONFIG_SF_DEFAULT_CS 1 #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0) #define CONFIG_SF_DEFAULT_SPEED 25000000 -#define CONFIG_ENV_SPI_CS (1 | 121 << 8) +#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS #define CONFIG_ENV_SPI_BUS 0 #define CONFIG_ENV_SPI_MAX_HZ 25000000 #define CONFIG_ENV_SPI_MODE (SPI_MODE_0) diff --git a/include/configs/mx6sabre_common.h b/include/configs/mx6sabre_common.h index e59a3b4..2d93d6c 100644 --- a/include/configs/mx6sabre_common.h +++ b/include/configs/mx6sabre_common.h @@ -74,7 +74,7 @@ #define CONFIG_SPI_FLASH_STMICRO #define CONFIG_MXC_SPI #define CONFIG_SF_DEFAULT_BUS 0 -#define CONFIG_SF_DEFAULT_CS (0 | (IMX_GPIO_NR(4, 9) << 8)) +#define CONFIG_SF_DEFAULT_CS 0 #define CONFIG_SF_DEFAULT_SPEED 20000000 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 #endif diff --git a/include/configs/mx6slevk.h b/include/configs/mx6slevk.h index 3d05a64..5b8309b 100644 --- a/include/configs/mx6slevk.h +++ b/include/configs/mx6slevk.h @@ -203,7 +203,7 @@ #define CONFIG_SPI_FLASH_STMICRO #define CONFIG_MXC_SPI #define CONFIG_SF_DEFAULT_BUS 0 -#define CONFIG_SF_DEFAULT_CS (0 | (IMX_GPIO_NR(4, 11) << 8)) +#define CONFIG_SF_DEFAULT_CS 0 #define CONFIG_SF_DEFAULT_SPEED 20000000 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 #endif diff --git a/include/configs/nitrogen6x.h b/include/configs/nitrogen6x.h index b2b17ce..d266f7d 100644 --- a/include/configs/nitrogen6x.h +++ b/include/configs/nitrogen6x.h @@ -53,7 +53,7 @@ #define CONFIG_SPI_FLASH_SST #define CONFIG_MXC_SPI #define CONFIG_SF_DEFAULT_BUS 0 -#define CONFIG_SF_DEFAULT_CS (0|(IMX_GPIO_NR(3, 19)<<8)) +#define CONFIG_SF_DEFAULT_CS 0 #define CONFIG_SF_DEFAULT_SPEED 25000000 #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0) #endif diff --git a/include/configs/vision2.h b/include/configs/vision2.h index 6891bf8..3f35076 100644 --- a/include/configs/vision2.h +++ b/include/configs/vision2.h @@ -57,11 +57,11 @@ * Use gpio 4 pin 25 as chip select for SPI flash * This corresponds to gpio 121 */ -#define CONFIG_SF_DEFAULT_CS (1 | (121 << 8)) +#define CONFIG_SF_DEFAULT_CS 1 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 #define CONFIG_SF_DEFAULT_SPEED 25000000 -#define CONFIG_ENV_SPI_CS (1 | (121 << 8)) +#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS #define CONFIG_ENV_SPI_BUS 0 #define CONFIG_ENV_SPI_MAX_HZ 25000000 #define CONFIG_ENV_SPI_MODE SPI_MODE_0 -- 1.9.1 _______________________________________________ U-Boot mailing list [email protected] http://lists.denx.de/mailman/listinfo/u-boot
