Add clear flag status register operation that some Micron SPI flash chips required after reading the flag status register to check some operations completion.
Signed-off-by: Hou Zhiqiang <[email protected]> --- Based on git://git.denx.de/u-boot.git. It also can be applied to git://www.denx.de/git/u-boot-mpc85xx.git. Tested on board T2080QDS and T2080RDB. drivers/mtd/spi/sf_internal.h | 9 +++++++++ drivers/mtd/spi/sf_ops.c | 36 ++++++++++++++++++++++++++++-------- 2 files changed, 37 insertions(+), 8 deletions(-) diff --git a/drivers/mtd/spi/sf_internal.h b/drivers/mtd/spi/sf_internal.h index 6bcd522..162dd87 100644 --- a/drivers/mtd/spi/sf_internal.h +++ b/drivers/mtd/spi/sf_internal.h @@ -36,6 +36,7 @@ #define CMD_WRITE_ENABLE 0x06 #define CMD_READ_CONFIG 0x35 #define CMD_FLAG_STATUS 0x70 +#define CMD_CLEAR_FLAG_STATUS 0x50 /* Read commands */ #define CMD_READ_ARRAY_SLOW 0x03 @@ -59,6 +60,8 @@ #define STATUS_QEB_WINSPAN (1 << 1) #define STATUS_QEB_MXIC (1 << 6) #define STATUS_PEC (1 << 7) +#define STATUS_PROT (1 << 1) +#define STATUS_ERASE (1 << 5) /* Flash timeout values */ #define SPI_FLASH_PROG_TIMEOUT (2 * CONFIG_SYS_HZ) @@ -120,6 +123,12 @@ static inline int spi_flash_cmd_write_disable(struct spi_flash *flash) return spi_flash_cmd(flash->spi, CMD_WRITE_DISABLE, NULL, 0); } +/* Clear flag status register */ +static inline int spi_flash_cmd_clear_flag_status(struct spi_flash *flash) +{ + return spi_flash_cmd(flash->spi, CMD_CLEAR_FLAG_STATUS, NULL, 0); +} + /* * Send the read status command to the device and wait for the wip * (write-in-progress) bit to clear itself. diff --git a/drivers/mtd/spi/sf_ops.c b/drivers/mtd/spi/sf_ops.c index 85cf22d..08ff1df 100644 --- a/drivers/mtd/spi/sf_ops.c +++ b/drivers/mtd/spi/sf_ops.c @@ -160,6 +160,7 @@ int spi_flash_cmd_wait_ready(struct spi_flash *flash, unsigned long timeout) unsigned long timebase; unsigned long flags = SPI_XFER_BEGIN; int ret; + int out_of_time = 1; u8 status; u8 check_status = 0x0; u8 poll_bit = STATUS_WIP; @@ -186,22 +187,41 @@ int spi_flash_cmd_wait_ready(struct spi_flash *flash, unsigned long timeout) WATCHDOG_RESET(); ret = spi_xfer(spi, 8, NULL, &status, 0); - if (ret) + if (ret) { + spi_xfer(spi, 0, NULL, NULL, SPI_XFER_END); return -1; + } - if ((status & poll_bit) == check_status) + if ((status & poll_bit) == check_status) { + out_of_time = 0; break; + } } while (get_timer(timebase) < timeout); spi_xfer(spi, 0, NULL, NULL, SPI_XFER_END); - if ((status & poll_bit) == check_status) - return 0; + if (out_of_time) { + /* Timed out */ + debug("SF: time out!\n"); + ret = -1; + } +#ifdef CONFIG_SPI_FLASH_STMICRO + else if (cmd == CMD_FLAG_STATUS) { + if (!(status & (STATUS_PROT | STATUS_ERASE))) { + ret = 0; + } else { + debug("SF: flag status error"); + ret = -1; + } - /* Timed out */ - debug("SF: time out!\n"); - return -1; + if (spi_flash_cmd_clear_flag_status(flash) < 0) { + debug("SF: clear flag status failed\n"); + ret = -1; + } + } +#endif + return ret; } int spi_flash_write_common(struct spi_flash *flash, const u8 *cmd, @@ -234,7 +254,7 @@ int spi_flash_write_common(struct spi_flash *flash, const u8 *cmd, ret = spi_flash_cmd_wait_ready(flash, timeout); if (ret < 0) { - debug("SF: write %s timed out\n", + debug("SF: write %s failed\n", timeout == SPI_FLASH_PROG_TIMEOUT ? "program" : "page erase"); return ret; -- 1.8.5 _______________________________________________ U-Boot mailing list [email protected] http://lists.denx.de/mailman/listinfo/u-boot
