On Friday, August 07, 2015 at 09:09:15 PM, Simon Glass wrote: > Hi Marcel, > > On 7 August 2015 at 00:41, Marcel Ziswiler <[email protected]> wrote: > > On Thu, 2015-08-06 at 23:29 -0600, Simon Glass wrote: > >> The memalign() function arguments are around the wrong way! > > > > I assume you meant that one: > > > > diff --git a/drivers/usb/eth/usb_ether.c b/drivers/usb/eth/usb_ether.c > > index 3c3e082..11d26be 100644 > > --- a/drivers/usb/eth/usb_ether.c > > +++ b/drivers/usb/eth/usb_ether.c > > @@ -73,7 +73,7 @@ int usb_ether_register(struct udevice *dev, struct > > ueth_data *ueth, int rxsize) > > > > } > > > > ueth->rxsize = rxsize; > > > > - ueth->rxbuf = memalign(rxsize, ARCH_DMA_MINALIGN); > > + ueth->rxbuf = memalign(ARCH_DMA_MINALIGN, rxsize); > > > > if (!ueth->rxbuf) > > > > return -ENOMEM; > >> > >> Definitely > >> worth seeing if that fixes it. For some reason rpi and minnowboard > >> seem to work even with this error. > > > > Unfortunately still the same: > > > > U-Boot SPL 2015.10-rc1-00188-gfac971b-dirty (Aug 07 2015 - 06:34:28) > > > > > > U-Boot 2015.10-rc1-00188-gfac971b-dirty (Aug 07 2015 - 06:34:28 +0000) > > > > TEGRA20 > > Model: Toradex Colibri T20 > > Board: Toradex Colibri T20 > > DRAM: 512 MiB > > NAND: 1024 MiB > > MMC: Tegra SD/MMC: 0 > > *** Warning - bad CRC, using default environment > > > > In: serial > > Out: serial > > Err: serial > > Net: Net Initialization Skipped > > No ethernet found. > > Hit any key to stop autoboot: 0 > > Colibri T20 # usb start > > starting USB... > > USB0: USB EHCI 1.00 > > USB1: USB EHCI 1.00 > > USB2: USB EHCI 1.00 > > scanning bus 1 for devices... 1 USB Device(s) found > > scanning bus 2 for devices... > > Warning: asix_eth using MAC address from ROM > > 2 USB Device(s) found > > scanning bus 0 for devices... 1 USB Device(s) found > > Colibri T20 # dhcp > > BOOTP broadcast 1 > > BOOTP broadcast 2 > > BOOTP broadcast 3 > > EHCI timed out on TD - token=0x8008d80 > > Rx: failed to receive: -5 > > BOOTP broadcast 4 > > BOOTP broadcast 5 > > EHCI timed out on TD - token=0x88008d80 > > Rx: failed to receive: -5 > > BOOTP broadcast 6 > > BOOTP broadcast 7 > > EHCI timed out on TD - token=0x8008d80 > > Rx: failed to receive: -5 > > BOOTP broadcast 8 > > BOOTP broadcast 9 > > EHCI timed out on TD - token=0x88008d80 > > Rx: failed to receive: -5 > > > > Retry time exceeded; starting again > > Colibri T20 # > > One point to make is that I have seen this on and off for a while. > When I tested the driver model EHCI support I found this bug. But then > when I turned off driver model it was still there. So I decided it was > pre-existing. Also I'm not sure that this error is handled correctly. > The code that times out does not retry properly. > > Marek do
I think there's a bit of this sentence missing. But the fix I pushed was for enumeration, not for this. > Regards, > Simon _______________________________________________ U-Boot mailing list [email protected] http://lists.denx.de/mailman/listinfo/u-boot
