On Tuesday, September 01, 2015 at 05:09:09 PM, Dinh Nguyen wrote: > On 08/31/2015 05:23 PM, Marek Vasut wrote: > > On Monday, August 31, 2015 at 09:57:05 PM, [email protected] wrote: > >> From: Dinh Nguyen <[email protected]> > >> > >> Add support for the Terasic DE0-Nano/Atlas-SoC Kit, which is a CycloneV > >> based board. The board can boot from SD/MMC. Ethernet is a bit different > >> because it has a KSZ9031 PHY, so for now, ethernet doesn't quite work > >> yet, as a few patches are needed to support the PHY. > > > > I thought we did support the KSZ9031 PHY. What's the problem ? > > Yeah, I just realized that. That's the problem when I've been working > with v2013.10 U-Boot! I'll have ethernet in V2.
Cool :-) > >> Signed-off-by: Dinh Nguyen <[email protected]> > >> --- > >> Hi Marek, > >> > >> This patch is based on your u-boot-socfpga/wip/boards branch. > > > > OK, that makes sense. > > > >> Thanks, > >> Dinh > >> --- > >> > >> arch/arm/dts/Makefile | 1 + > >> arch/arm/dts/socfpga_cyclone5_de0_sockit.dts | 61 +++ > >> arch/arm/mach-socfpga/Kconfig | 7 + > >> board/terasic/de0/MAINTAINERS | 5 + > >> board/terasic/de0/Makefile | 9 + > > > > I think it might be clearer to rename it to de0-nano-soc, what do you > > think ? What's the difference between de0-nano-soc and atlas btw ? > > I don't know. From the website, DE0-Nano-SoC Kit/Atlas-SoC Kit, so > DE0_Nano_SoCKit is synonymous with Atlas Sockit? See the other email I guess. > > [...] > > > >> diff --git a/configs/socfpga_de0_defconfig > >> b/configs/socfpga_de0_defconfig new file mode 100644 > >> index 0000000..000f322 > >> --- /dev/null > >> +++ b/configs/socfpga_de0_defconfig > >> @@ -0,0 +1,21 @@ > >> +CONFIG_ARM=y > >> +CONFIG_ARCH_SOCFPGA=y > >> +CONFIG_TARGET_SOCFPGA_CYCLONE5=y > >> +CONFIG_TARGET_SOCFPGA_TERASIC_DE0=y > >> +CONFIG_DEFAULT_DEVICE_TREE="socfpga_cyclone5_de0_sockit" > >> +CONFIG_SPL=y > >> +# CONFIG_CMD_IMLS is not set > >> +# CONFIG_CMD_FLASH is not set > >> +CONFIG_OF_CONTROL=y > >> +CONFIG_DM_ETH=y > >> +CONFIG_NETDEVICES=y > >> +CONFIG_ETH_DESIGNWARE=y > >> +CONFIG_DM_GPIO=y > >> +CONFIG_DWAPB_GPIO=y > >> +CONFIG_SPL_DM=y > >> +CONFIG_SPL_MMC_SUPPORT=y > >> +CONFIG_DM_SEQ_ALIAS=y > > > > I think you don't need the DM_SEQ_ALIAS, it's needed only for QSPI > > to enforce the SPI NOR ordering. > > Right, I missed this one. :) > <snip> > > >> + > >> +/* USB */ > >> +#ifdef CONFIG_CMD_USB > >> +#define CONFIG_USB_DWC2_REG_ADDR SOCFPGA_USB1_ADDRESS > >> +#endif > >> +#define CONFIG_G_DNL_MANUFACTURER "Terasic" > >> + > >> +/* Extra Environment */ > >> +#define CONFIG_HOSTNAME socfpga_cyclone5 > > > > socfpga_d0_nano_soc might be better ;-) > > Yeah..missed this one too. Thanks! _______________________________________________ U-Boot mailing list [email protected] http://lists.denx.de/mailman/listinfo/u-boot
