On Tue, 2015-09-01 at 10:30 +0200, [email protected] wrote: > On Tuesday, September 01, 2015 at 06:54:14 AM, Chin Liang See wrote: > > On Mon, 2015-08-31 at 14:57 -0500, [email protected] wrote: > > > From: Dinh Nguyen <[email protected]> > > > > > > Add support for the Terasic DE0-Nano/Atlas-SoC Kit, which is a CycloneV > > > based board. The board can boot from SD/MMC. Ethernet is a bit different > > > because it has a KSZ9031 PHY, so for now, ethernet doesn't quite work > > > yet, as a few patches are needed to support the PHY. > > > > > > Signed-off-by: Dinh Nguyen <[email protected]> > > > --- > > > Hi Marek, > > > > > > This patch is based on your u-boot-socfpga/wip/boards branch. > > > > > > Thanks, > > > Dinh > > > --- > > > > > > arch/arm/dts/Makefile | 1 + > > > arch/arm/dts/socfpga_cyclone5_de0_sockit.dts | 61 +++ > > > arch/arm/mach-socfpga/Kconfig | 7 + > > > board/terasic/de0/MAINTAINERS | 5 + > > > board/terasic/de0/Makefile | 9 + > > > board/terasic/de0/qts/iocsr_config.h | 658 > > > +++++++++++++++++++++++++++ board/terasic/de0/qts/pinmux_config.h > > > | 220 +++++++++ > > > board/terasic/de0/qts/pll_config.h | 85 ++++ > > > board/terasic/de0/qts/sdram_config.h | 342 ++++++++++++++ > > > board/terasic/de0/socfpga.c | 22 + > > > configs/socfpga_de0_defconfig | 21 + > > > include/configs/socfpga_de0.h | 88 ++++ > > > 12 files changed, 1519 insertions(+) > > > create mode 100644 arch/arm/dts/socfpga_cyclone5_de0_sockit.dts > > > create mode 100644 board/terasic/de0/MAINTAINERS > > > create mode 100644 board/terasic/de0/Makefile > > > create mode 100644 board/terasic/de0/qts/iocsr_config.h > > > create mode 100644 board/terasic/de0/qts/pinmux_config.h > > > create mode 100644 board/terasic/de0/qts/pll_config.h > > > create mode 100644 board/terasic/de0/qts/sdram_config.h > > > create mode 100644 board/terasic/de0/socfpga.c > > > create mode 100644 configs/socfpga_de0_defconfig > > > create mode 100644 include/configs/socfpga_de0.h > > > > > > diff --git a/include/configs/socfpga_de0.h > > > b/include/configs/socfpga_de0.h new file mode 100644 > > > index 0000000..47e18ba > > > --- /dev/null > > > +++ b/include/configs/socfpga_de0.h > > > @@ -0,0 +1,88 @@ > > > +/* > > > + * Copyright (C) 2015 Marek Vasut <[email protected]> > > > + * > > > + * SPDX-License-Identifier: GPL-2.0+ > > > + */ > > > +#ifndef __CONFIG_TERASIC_DE0_H__ > > > +#define __CONFIG_TERASIC_DE0_H__ > > > + > > > +#include <asm/arch/socfpga_base_addrs.h> > > > + > > > +/* U-Boot Commands */ > > > +#define CONFIG_SYS_NO_FLASH > > > +#define CONFIG_DOS_PARTITION > > > +#define CONFIG_FAT_WRITE > > > +#define CONFIG_HW_WATCHDOG > > > + > > > +#define CONFIG_CMD_ASKENV > > > +#define CONFIG_CMD_BOOTZ > > > +#define CONFIG_CMD_CACHE > > > +#define CONFIG_CMD_DFU > > > +#define CONFIG_CMD_DHCP > > > +#define CONFIG_CMD_EXT4 > > > +#define CONFIG_CMD_EXT4_WRITE > > > +#define CONFIG_CMD_FAT > > > +#define CONFIG_CMD_FS_GENERIC > > > +#define CONFIG_CMD_GPIO > > > +#define CONFIG_CMD_GREPENV > > > +#define CONFIG_CMD_MII > > > +#define CONFIG_CMD_MMC > > > +#define CONFIG_CMD_PING > > > +#define CONFIG_CMD_USB > > > +#define CONFIG_CMD_USB_MASS_STORAGE > > > + > > > +/* Memory configurations */ > > > +#define PHYS_SDRAM_1_SIZE 0x40000000 /* 1GiB */ > > > + > > > +/* Booting Linux */ > > > +#define CONFIG_BOOTDELAY 3 > > > +#define CONFIG_BOOTFILE "fitImage" > > > > Wonder this should be zImage as the mmcload still using zImage? > > Or maybe the mmcload should be fixed instead ; fitImage is preferred.
Yup, I agreed that as we can enable checksum even its zimage. Thanks Chin Liang _______________________________________________ U-Boot mailing list [email protected] http://lists.denx.de/mailman/listinfo/u-boot
