Hi Stefano, On Tue, Oct 11, 2016 at 9:00 AM, Jagan Teki <jt...@openedev.com> wrote: > Hi Stefano, > > On Sun, Oct 9, 2016 at 8:15 PM, Jagan Teki <jagannadh.t...@gmail.com> wrote: >> Hi Stefano, >> >> On Sat, Oct 8, 2016 at 6:00 PM, Jagan Teki <jt...@openedev.com> wrote: >>> From: Jagan Teki <ja...@amarulasolutions.com> >>> >>> This series supports Engicam i.CoreM6 QDL modules on top of >>> u-boot-imx/master >>> and test on the respective starter kits as well. >>> >>> Tested both MMC and NAND boot. >>> >>> Changes for v7: >>> - Add patch to CONFIG_DEFAULT_FDT_FILE to defconfigs >>> - Rebase on u-boot-imx/master >>> >>> Changes for v6: >>> - Rebase to u-boot-imx/master >>> - Move few SPL configs to defconfigs >>> >>> Changes for v5: >>> - Add NAND support >>> >>> Changes for v4: >>> - Add 'net: Kconfig: Add FEC_MXC entry' patch >>> - Updated ENV configs along with comments >>> - Restructured configs for more readability >>> - Add CONFIG_ENV_OVERWRITE >>> - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig >>> >>> Changes for v3: >>> - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" >>> patch >>> - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch >>> - Add minimal devicetree support for Engicam i.CoreM6 QDL >>> - Add is_mx6dl() >>> - Add is_mx6solo() >>> - Use is_mx6dq() >>> - Add last commit sha1 and header in pull devicetree files from >>> Linux >>> >>> Changes for v2: >>> - Make static to local iomux structure in board file >>> - Corrected rowaddr in mx6_ddr3_cfg >>> - Used imx_ddr_size >>> - Add FEC support and tested the same >>> - Add DM_GPIO, DM_MMC support >>> - Add pinctrl support >>> - Add devicetree support >>> >>> Jagan Teki (21): >>> serial: Kconfig: Add MXC_UART entry >>> thermal: Kconfig: Add IMX_THERMAL entry >>> config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs >>> arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support >>> net: Kconfig: Add FEC_MXC entry >>> imx6: icorem6: Add ENET support >>> imx: s/docs\/README.imximage/doc\/README.imximage/g >>> arm: dts: Add devicetree for i.MX6DL >>> arm: dts: Add devicetree for i.MX6DQL >>> arm: dts: imx6dl: Add pinctrl defines >>> dt-bindings: clock: imx6qdl: Add clock defines >>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo >>> imx6q: icorem6: Enable pinctrl driver >>> engicam: icorem6: Add DM_GPIO, DM_MMC support >>> arm: dts: Add devicetree for i.MX6Q >>> arm: dts: imx6q: Add pinctrl defines >>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual >>> mtd: nand: Kconfig: Add NAND_MXS entry >>> imx6: icorem6: Add NAND support >>> imx6: icorem6: Enable MTD device support >>> imx6: icorem6: Add default mtd nand partition table >> >> All set now, please do apply. > > Let me know if you still find any issues, otherwise apply this. >
Any help? thanks! -- Jagan Teki Free Software Engineer | www.openedev.com U-Boot, Linux | Upstream Maintainer Hyderabad, India. _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot