Hi Jagan, On 17/10/2016 05:40, Jagan Teki wrote: > Hi Stefano, > > On Tue, Oct 11, 2016 at 9:00 AM, Jagan Teki <jt...@openedev.com> wrote: >> Hi Stefano, >> >> On Sun, Oct 9, 2016 at 8:15 PM, Jagan Teki <jagannadh.t...@gmail.com> wrote: >>> Hi Stefano, >>> >>> On Sat, Oct 8, 2016 at 6:00 PM, Jagan Teki <jt...@openedev.com> wrote: >>>> From: Jagan Teki <ja...@amarulasolutions.com> >>>> >>>> This series supports Engicam i.CoreM6 QDL modules on top of >>>> u-boot-imx/master >>>> and test on the respective starter kits as well. >>>> >>>> Tested both MMC and NAND boot. >>>> >>>> Changes for v7: >>>> - Add patch to CONFIG_DEFAULT_FDT_FILE to defconfigs >>>> - Rebase on u-boot-imx/master >>>> >>>> Changes for v6: >>>> - Rebase to u-boot-imx/master >>>> - Move few SPL configs to defconfigs >>>> >>>> Changes for v5: >>>> - Add NAND support >>>> >>>> Changes for v4: >>>> - Add 'net: Kconfig: Add FEC_MXC entry' patch >>>> - Updated ENV configs along with comments >>>> - Restructured configs for more readability >>>> - Add CONFIG_ENV_OVERWRITE >>>> - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig >>>> >>>> Changes for v3: >>>> - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" >>>> patch >>>> - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch >>>> - Add minimal devicetree support for Engicam i.CoreM6 QDL >>>> - Add is_mx6dl() >>>> - Add is_mx6solo() >>>> - Use is_mx6dq() >>>> - Add last commit sha1 and header in pull devicetree files from >>>> Linux >>>> >>>> Changes for v2: >>>> - Make static to local iomux structure in board file >>>> - Corrected rowaddr in mx6_ddr3_cfg >>>> - Used imx_ddr_size >>>> - Add FEC support and tested the same >>>> - Add DM_GPIO, DM_MMC support >>>> - Add pinctrl support >>>> - Add devicetree support >>>> >>>> Jagan Teki (21): >>>> serial: Kconfig: Add MXC_UART entry >>>> thermal: Kconfig: Add IMX_THERMAL entry >>>> config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs >>>> arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support >>>> net: Kconfig: Add FEC_MXC entry >>>> imx6: icorem6: Add ENET support >>>> imx: s/docs\/README.imximage/doc\/README.imximage/g >>>> arm: dts: Add devicetree for i.MX6DL >>>> arm: dts: Add devicetree for i.MX6DQL >>>> arm: dts: imx6dl: Add pinctrl defines >>>> dt-bindings: clock: imx6qdl: Add clock defines >>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo >>>> imx6q: icorem6: Enable pinctrl driver >>>> engicam: icorem6: Add DM_GPIO, DM_MMC support >>>> arm: dts: Add devicetree for i.MX6Q >>>> arm: dts: imx6q: Add pinctrl defines >>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual >>>> mtd: nand: Kconfig: Add NAND_MXS entry >>>> imx6: icorem6: Add NAND support >>>> imx6: icorem6: Enable MTD device support >>>> imx6: icorem6: Add default mtd nand partition table >>> >>> All set now, please do apply. >> >> Let me know if you still find any issues, otherwise apply this. >> > > Any help?
Sorry, I was last week at ELCE - I will go on with your patches (and the other ones left pending) this week. Regards, Stefano -- ===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sba...@denx.de ===================================================================== _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot