From: Konstantin Porotchkin <[email protected]> Add support for "marvell,vbus-gpio" property to mvebu XHCI board init function. This option is valid when CONFIG_DM_GPIO=y
Change-Id: I930b3ebe001e50ae8d5abe1f3c774bcdb1739e64 Signed-off-by: Konstantin Porotchkin <[email protected]> Cc: Stefan Roese <[email protected]> Cc: Nadav Haklai <[email protected]> Cc: Neta Zur Hershkovits <[email protected]> Cc: Omri Itach <[email protected]> Cc: Igal Liberman <[email protected]> Cc: Haim Boot <[email protected]> Cc: Hanna Hawa <[email protected]> --- board/Marvell/mvebu_armada-8k/board.c | 32 ++++++++++++++++------- board/Marvell/mvebu_db-88f3720/board.c | 2 +- doc/device-tree-bindings/usb/marvell.xhci-usb.txt | 29 ++++++++++++++++++++ drivers/usb/host/xhci-mvebu.c | 5 ++-- 4 files changed, 55 insertions(+), 13 deletions(-) create mode 100644 doc/device-tree-bindings/usb/marvell.xhci-usb.txt diff --git a/board/Marvell/mvebu_armada-8k/board.c b/board/Marvell/mvebu_armada-8k/board.c index 7d1b5d9..aa6a6d7 100644 --- a/board/Marvell/mvebu_armada-8k/board.c +++ b/board/Marvell/mvebu_armada-8k/board.c @@ -8,6 +8,7 @@ #include <dm.h> #include <i2c.h> #include <asm/io.h> +#include <asm/gpio.h> #include <asm/arch/cpu.h> #include <asm/arch/soc.h> @@ -95,19 +96,23 @@ int board_xhci_config(void) return 0; } -int board_xhci_enable(void) +int board_xhci_enable(struct udevice *usb_dev) { struct udevice *dev; +#ifdef CONFIG_DM_GPIO + struct gpio_desc vbus_gpio; +#endif int ret; u8 buf[8]; + /* + * This function enables all USB ports simultaniously, + * it only needs to get called once + */ + if (usb_enabled) + return 0; + if (of_machine_is_compatible("marvell,armada7040-db")) { - /* - * This function enables all USB ports simultaniously, - * it only needs to get called once - */ - if (usb_enabled) - return 0; /* Configure IO exander PCA9555: 7bit address 0x21 */ ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev); @@ -131,10 +136,19 @@ int board_xhci_enable(void) return -EIO; } - mdelay(500); /* required delay to let output value settle */ - usb_enabled = 1; } +#ifdef CONFIG_DM_GPIO + gpio_request_by_name(usb_dev, "marvell,vbus-gpio", 0, + &vbus_gpio, GPIOD_IS_OUT); + + if (dm_gpio_is_valid(&vbus_gpio)) + dm_gpio_set_value(&vbus_gpio, 1); +#endif + + mdelay(500); /* required delay to let output value settle */ + usb_enabled = 1; + return 0; } diff --git a/board/Marvell/mvebu_db-88f3720/board.c b/board/Marvell/mvebu_db-88f3720/board.c index edf88c7..75679ff 100644 --- a/board/Marvell/mvebu_db-88f3720/board.c +++ b/board/Marvell/mvebu_db-88f3720/board.c @@ -69,7 +69,7 @@ int board_ahci_enable(void) } /* Board specific xHCI enable code */ -int board_xhci_enable(void) +int board_xhci_enable(struct udevice *usb_dev) { struct udevice *dev; int ret; diff --git a/doc/device-tree-bindings/usb/marvell.xhci-usb.txt b/doc/device-tree-bindings/usb/marvell.xhci-usb.txt new file mode 100644 index 0000000..b0a53ad --- /dev/null +++ b/doc/device-tree-bindings/usb/marvell.xhci-usb.txt @@ -0,0 +1,29 @@ +Marvell SOC USB controllers + +This controller is integrated in Armada 3700/8K. +It uses the same properties as a generic XHCI host controller + +Required properties : + - compatible: should be one or more of: + - "marvell,armada3700-xhci", "generic-xhci" for Armada 37xx SoCs + - "marvell,armada-8k-xhci", "generic-xhci" for Armada A8K SoCs + - reg: should contain address and length of the standard XHCI + register set for the device. + - interrupts: one XHCI interrupt should be described here. + +Optional properties: + - clocks: reference to a clock + - marvell,vbus-gpio : If present, specifies a gpio that needs to be + activated for the bus to be powered. + +Example: + cpm_usb3_0: usb3@500000 { + compatible = "marvell,armada-8k-xhci", + "generic-xhci"; + reg = <0x500000 0x4000>; + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpm_syscon0 1 22>; + marvell,vbus-gpio = <&cpm_gpio1 15 GPIO_ACTIVE_HIGH>; + status = "disabled"; + }; + diff --git a/drivers/usb/host/xhci-mvebu.c b/drivers/usb/host/xhci-mvebu.c index 46eb937..843a51b 100644 --- a/drivers/usb/host/xhci-mvebu.c +++ b/drivers/usb/host/xhci-mvebu.c @@ -10,7 +10,6 @@ #include <dm.h> #include <fdtdec.h> #include <usb.h> -#include <asm/gpio.h> #include "xhci.h" @@ -34,7 +33,7 @@ struct mvebu_xhci { * Dummy implementation that can be overwritten by a board * specific function */ -__weak int board_xhci_enable(void) +__weak int board_xhci_enable(struct udevice *usb_dev) { return 0; } @@ -51,7 +50,7 @@ static int xhci_usb_probe(struct udevice *dev) hcor = (struct xhci_hcor *)((uintptr_t)ctx->hcd + len); /* Enable USB xHCI (VBUS, reset etc) in board specific code */ - board_xhci_enable(); + board_xhci_enable(dev); return xhci_register(dev, ctx->hcd, hcor); } -- 2.7.4 _______________________________________________ U-Boot mailing list [email protected] http://lists.denx.de/mailman/listinfo/u-boot
