Hi Marek
On 03/17/2017 05:42 PM, Marek Vasut wrote:
> On 03/17/2017 05:25 PM, [email protected] wrote:
>> From: Patrice Chotard <[email protected]>
>>
>> This patch adds the ST glue logic to manage the DWC3 HC
>> on STiH407 SoC family. It configures the internal glue
>> logic and syscfg registers.
>>
>> Part of this code been extracted from kernel.org driver
>> (drivers/usb/dwc3/dwc3-st.c)
>>
>> Signed-off-by: Patrice Chotard <[email protected]>
>> ---
>> arch/arm/include/asm/arch-stih410/sys_proto.h | 11 +++
>> drivers/usb/dwc3/Kconfig | 8 ++
>> drivers/usb/dwc3/Makefile | 1 +
>> drivers/usb/dwc3/dwc3-sti.c | 137
>> ++++++++++++++++++++++++++
>> include/dwc3-sti-uboot.h | 50 ++++++++++
>> 5 files changed, 207 insertions(+)
>> create mode 100644 arch/arm/include/asm/arch-stih410/sys_proto.h
>> create mode 100644 drivers/usb/dwc3/dwc3-sti.c
>> create mode 100644 include/dwc3-sti-uboot.h
>>
>> diff --git a/arch/arm/include/asm/arch-stih410/sys_proto.h
>> b/arch/arm/include/asm/arch-stih410/sys_proto.h
>> new file mode 100644
>> index 0000000..5c40d3b
>> --- /dev/null
>> +++ b/arch/arm/include/asm/arch-stih410/sys_proto.h
>> @@ -0,0 +1,11 @@
>> +/*
>> + * Copyright (c) 2017
>> + * Patrice Chotard <[email protected]>
>> + *
>> + * SPDX-License-Identifier: GPL-2.0+
>> + */
>> +
>> +#ifndef _ASM_ARCH_SYS_PROTO_H
>> +#define _ASM_ARCH_SYS_PROTO_H
>> +
>> +#endif /* _ASM_ARCH_SYS_PROTO_H */
>> diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
>> index e93398f..51a7a00 100644
>> --- a/drivers/usb/dwc3/Kconfig
>> +++ b/drivers/usb/dwc3/Kconfig
>> @@ -37,6 +37,14 @@ config USB_DWC3_OMAP
>>
>> Say 'Y' here if you have one such device
>>
>> +config USB_DWC3_STI
>> + bool "STMicroelectronics STiH407 family glue driver"
>> + help
>> + STMicroelectronics STiH407 family SoCs use this IP for
>> + USB2/3 functionality.
>> +
>> + Say 'Y' here if you have one such device
>> +
>> menu "PHY Subsystem"
>>
>> config USB_DWC3_PHY_OMAP
>> diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
>> index 2964bae..753912d 100644
>> --- a/drivers/usb/dwc3/Makefile
>> +++ b/drivers/usb/dwc3/Makefile
>> @@ -11,3 +11,4 @@ obj-$(CONFIG_USB_DWC3_GADGET) += gadget.o
>> ep0.o
>> obj-$(CONFIG_USB_DWC3_OMAP) += dwc3-omap.o
>> obj-$(CONFIG_USB_DWC3_PHY_OMAP) += ti_usb_phy.o
>> obj-$(CONFIG_USB_DWC3_PHY_SAMSUNG) += samsung_usb_phy.o
>> +obj-$(CONFIG_USB_DWC3_STI) += dwc3-sti.o
>> diff --git a/drivers/usb/dwc3/dwc3-sti.c b/drivers/usb/dwc3/dwc3-sti.c
>> new file mode 100644
>> index 0000000..5ff3e76
>> --- /dev/null
>> +++ b/drivers/usb/dwc3/dwc3-sti.c
>> @@ -0,0 +1,137 @@
>> +/*
>> + * dwc3-sti.c - STiH407 family DWC3 specific Glue layer
>> + * Copyright (c) 2017
>> + * Patrice Chotard <[email protected]>
>> + *
>> + * SPDX-License-Identifier: GPL-2.0+
>> + */
>> +
>> +#include <asm/io.h>
>> +#include <common.h>
>> +#include <dm.h>
>> +#include <dwc3-sti-uboot.h>
>> +#include <fdtdec.h>
>> +#include <regmap.h>
>> +#include <syscon.h>
>> +#include <usb.h>
>> +
>> +DECLARE_GLOBAL_DATA_PTR;
>> +
>> +__weak int __board_usb_init(int index, enum usb_init_type init)
>> +{
>> + return 0;
>> +}
>> +/*int board_usb_init(int index, enum usb_init_type init)*/
>> +/* __attribute__((weak, alias("__board_usb_init")));*/
>> +
>> +static int sti_dwc3_drd_init(struct sti_dwc3_platdata *plat)
>> +{
>> + unsigned long val;
>> +
>> + val = readl(plat->syscfg_base + plat->syscfg_offset);
>> +
>> + val &= USB3_CONTROL_MASK;
>> +
>> + switch (plat->mode) {
>> + case USB_DR_MODE_PERIPHERAL:
>> + val &= ~(USB3_DELAY_VBUSVALID
>> + | USB3_SEL_FORCE_OPMODE | USB3_FORCE_OPMODE(0x3)
>> + | USB3_SEL_FORCE_DPPULLDOWN2 | USB3_FORCE_DPPULLDOWN2
>> + | USB3_SEL_FORCE_DMPULLDOWN2 | USB3_FORCE_DMPULLDOWN2);
>> +
>> + val |= USB3_DEVICE_NOT_HOST | USB3_FORCE_VBUSVALID;
>> + break;
>> +
>> + case USB_DR_MODE_HOST:
>> + val &= ~(USB3_DEVICE_NOT_HOST | USB3_FORCE_VBUSVALID
>> + | USB3_SEL_FORCE_OPMODE | USB3_FORCE_OPMODE(0x3)
>> + | USB3_SEL_FORCE_DPPULLDOWN2 | USB3_FORCE_DPPULLDOWN2
>> + | USB3_SEL_FORCE_DMPULLDOWN2 | USB3_FORCE_DMPULLDOWN2);
>> +
>> + val |= USB3_DELAY_VBUSVALID;
>> + break;
>> +
>> + default:
>> + error("Unsupported mode of operation %d\n", plat->mode);
>> + return -EINVAL;
>> + }
>> + return writel(val, plat->syscfg_base + plat->syscfg_offset);
>> +}
>> +
>> +static void sti_dwc3_init(struct sti_dwc3_platdata *plat)
>> +{
>> + unsigned long reg;
>> +
>> + reg = readl(plat->glue_base + CLKRST_CTRL);
>> +
>> + reg |= AUX_CLK_EN | EXT_CFG_RESET_N | XHCI_REVISION;
>> + reg &= ~SW_PIPEW_RESET_N;
>> +
>> + writel(reg, plat->glue_base + CLKRST_CTRL);
>> +
>> + /* configure mux for vbus, powerpresent and bvalid signals */
>> + reg = readl(plat->glue_base + USB2_VBUS_MNGMNT_SEL1);
>> +
>> + reg |= SEL_OVERRIDE_VBUSVALID(USB2_VBUS_UTMIOTG) |
>> + SEL_OVERRIDE_POWERPRESENT(USB2_VBUS_UTMIOTG) |
>> + SEL_OVERRIDE_BVALID(USB2_VBUS_UTMIOTG);
>> +
>> + writel(reg, plat->glue_base + USB2_VBUS_MNGMNT_SEL1);
>> +
>> + reg = readl(plat->glue_base + CLKRST_CTRL);
>> + reg |= SW_PIPEW_RESET_N;
>> + writel(reg, plat->glue_base + CLKRST_CTRL);
>
> setbits_le32() ?
Ok, i will use setbits_le32 instead
>
>> +}
>> +
>> +int sti_dwc3_glue_init(enum usb_dr_mode mode)
>> +{
>> + struct sti_dwc3_platdata plat;
>> + struct fdtdec_phandle_args syscfg_phandle;
>> + struct udevice *syscon;
>> + struct regmap *regmap;
>> + int node, ret;
>> + const void *blob = gd->fdt_blob;
>> + u32 reg[4];
>> +
>> + /* find the dwc3 node */
>> + node = fdt_node_offset_by_compatible(blob, -1, "st,stih407-dwc3");
>> +
>> + ret = fdtdec_get_int_array(blob, node, "reg", reg, ARRAY_SIZE(reg));
>> + if (ret) {
>> + error("unable to find st,stih407-dwc3 reg property(%d)\n", ret);
>> + return ret;
>> + }
>> +
>> + plat.glue_base = reg[0];
>> + plat.syscfg_offset = reg[2];
>> + plat.mode = mode;
>> +
>> + /* get corresponding syscon phandle */
>> + ret = fdtdec_parse_phandle_with_args(gd->fdt_blob, node,
>> + "st,syscfg", NULL, 0, 0,
>> + &syscfg_phandle);
>> + if (ret < 0) {
>> + error("Can't get syscfg phandle: %d\n", ret);
>> + return ret;
>> + }
>> +
>> + ret = uclass_get_device_by_of_offset(UCLASS_SYSCON, syscfg_phandle.node,
>> + &syscon);
>> + if (ret) {
>> + error("unable to find syscon device (%d)\n", ret);
>> + return ret;
>> + }
>> +
>> + /* get syscfg-reg base address */
>> + regmap = syscon_get_regmap(syscon);
>> + if (!regmap) {
>> + error("unable to find regmap\n");
>> + return -ENODEV;
>> + }
>> + plat.syscfg_base = regmap->base;
>> +
>> + sti_dwc3_drd_init(&plat);
>> + sti_dwc3_init(&plat);
>> +
>> + return 0;
>> +}
>> diff --git a/include/dwc3-sti-uboot.h b/include/dwc3-sti-uboot.h
>> new file mode 100644
>> index 0000000..c7bb770
>> --- /dev/null
>> +++ b/include/dwc3-sti-uboot.h
>> @@ -0,0 +1,50 @@
>> +/*
>> + * Copyright (c) 2017
>> + * Patrice Chotard <[email protected]>
>> + *
>> + * SPDX-License-Identifier: GPL-2.0+
>> + */
>> +
>> +#ifndef __DWC3_STI_UBOOT_H_
>> +#define __DWC3_STI_UBOOT_H_
>> +
>> +#include <linux/usb/otg.h>
>> +
>> +/* glue registers */
>> +#define CLKRST_CTRL 0x00
>> +#define AUX_CLK_EN BIT(0)
>> +#define SW_PIPEW_RESET_N BIT(4)
>> +#define EXT_CFG_RESET_N BIT(8)
>> +
>> +#define XHCI_REVISION BIT(12)
>> +
>> +#define USB2_VBUS_MNGMNT_SEL1 0x2C
>> +#define USB2_VBUS_UTMIOTG 0x1
>> +
>> +#define SEL_OVERRIDE_VBUSVALID(n) (n << 0)
>> +#define SEL_OVERRIDE_POWERPRESENT(n) (n << 4)
>> +#define SEL_OVERRIDE_BVALID(n) (n << 8)
>> +
>> +/* Static DRD configuration */
>> +#define USB3_CONTROL_MASK 0xf77
>> +
>> +#define USB3_DEVICE_NOT_HOST BIT(0)
>> +#define USB3_FORCE_VBUSVALID BIT(1)
>> +#define USB3_DELAY_VBUSVALID BIT(2)
>> +#define USB3_SEL_FORCE_OPMODE BIT(4)
>> +#define USB3_FORCE_OPMODE(n) (n << 5)
>
> The (n) should be in parenthesis ...
>
>> +#define USB3_SEL_FORCE_DPPULLDOWN2 BIT(8)
>> +#define USB3_FORCE_DPPULLDOWN2 BIT(9)
>> +#define USB3_SEL_FORCE_DMPULLDOWN2 BIT(10)
>> +#define USB3_FORCE_DMPULLDOWN2 BIT(11)
>> +
>> +struct sti_dwc3_platdata {
>> + phys_addr_t syscfg_base;
>> + phys_addr_t glue_base;
>> + phys_addr_t syscfg_offset;
>> + enum usb_dr_mode mode;
>> +};
>> +
>> +int sti_dwc3_glue_init(enum usb_dr_mode mode);
>> +
>> +#endif /* __DWC3_STI_UBOOT_H_ */
>>
>
>
_______________________________________________
U-Boot mailing list
[email protected]
https://lists.denx.de/listinfo/u-boot
