On 07/29/2017 05:25 PM, Bin Meng wrote: > Hi Marek, > > On Fri, Jul 21, 2017 at 8:36 PM, Marek Vasut <[email protected]> wrote: >> On 07/21/2017 02:34 PM, Bin Meng wrote: >>> Hi Marek, >>> >>> On Fri, Jul 21, 2017 at 6:06 PM, Marek Vasut <[email protected]> wrote: >>>> On 07/21/2017 12:04 PM, Bin Meng wrote: >>>>> Hi Marek, >>>>> >>>>> On Fri, Jul 21, 2017 at 4:56 PM, Marek Vasut <[email protected]> wrote: >>>>>> On 07/21/2017 10:54 AM, Bin Meng wrote: >>>>>>> Hi Marek, >>>>>>> >>>>>>> On Thu, Jul 20, 2017 at 8:20 PM, Marek Vasut <[email protected]> wrote: >>>>>>>> On 07/20/2017 02:16 PM, Bin Meng wrote: >>>>>>>>> Hi Marek, >>>>>>>>> >>>>>>>>> On Thu, Jul 20, 2017 at 7:12 AM, Bin Meng <[email protected]> wrote: >>>>>>>>>> This series is the final series of the xHCI driver update. >>>>>>>>>> >>>>>>>>>> This adds the missing interrupt transfer support to xHCI driver, so >>>>>>>>>> that devices like USB keyboard that uses interrupt transfer when >>>>>>>>>> CONFIG_SYS_USB_EVENT_POLL is defined can work. >>>>>>>>>> >>>>>>>>>> This also adds full speed device support. Unlike low/high/super speed >>>>>>>>>> devices, full speed device may report its endpoint 0 max packet size >>>>>>>>>> as 8/16/32/64. xHCI driver guesses 64 for the first attempt to get >>>>>>>>>> the >>>>>>>>>> initial 8 bytes device descriptor, and later adjusts the context for >>>>>>>>>> endpoint 0. >>>>>>>>>> >>>>>>>>>> This series also made several updates to xHCI driver to conform with >>>>>>>>>> the spec. >>>>>>>>>> >>>>>>>>>> Previous two series: >>>>>>>>>> [1]: usb: xhci: Fix USB xHCI support on Intel platform >>>>>>>>>> https://lists.denx.de/pipermail/u-boot/2017-June/296166.html >>>>>>>>>> [2]: usb: hub: Support USB 3.0 hubs >>>>>>>>>> https://lists.denx.de/pipermail/u-boot/2017-June/296284.html >>>>>>>>>> >>>>>>>>>> This series is available at u-boot-x86/xhci-working3 for testing. >>>>>>>>>> >>>>>>>>>> Changes in v3: >>>>>>>>>> - rebase on u-boot-usb/master >>>>>>>>>> - add changes to poplar.h >>>>>>>>>> >>>>>>>>>> Bin Meng (13): >>>>>>>>>> usb: xhci: Add interrupt transfer support >>>>>>>>>> usb: configs: Clean up CONFIG_SYS_USB_EVENT_POLL_(xxx) in board >>>>>>>>>> configs >>>>>>>>>> usb: kbd: kconfig: Set a default polling mechanism for USB keyboard >>>>>>>>>> usb: Only get 64 bytes device descriptor for full speed devices >>>>>>>>>> usb: Read device descriptor after device is addressed for xHCI >>>>>>>>>> usb: xhci: Fix max packet size for full speed device endpoint 0 >>>>>>>>>> usb: hub: Clear port reset before usb_hub_port_connect_change() >>>>>>>>>> usb: hub: Clear BH reset status change for a 3.0 hub >>>>>>>>>> usb: Handle audio extension endpoint descriptor in >>>>>>>>>> usb_parse_config() >>>>>>>>>> usb: xhci: Honor endpoint's interval >>>>>>>>>> usb: xhci: Program max burst size for endpoint >>>>>>>>>> usb: xhci: Set 'Error Count' to 0 for isoch endpoints >>>>>>>>>> usb: xhci: Set 'Average TRB Length' to 8 for control endpoints >>>>>>>>>> >>>>>>>>> >>>>>>>>> This is the last xHCI series I have. Can you please take a look and >>>>>>>>> apply? >>>>>>>> >>>>>>>> I'd like to see some RB/TB from Stefan Roese first if possible. >>>>>>>> >>>>>>> >>>>>>> OK, if that's the case, can you send a pull request to Tom to get usb >>>>>>> in? So that I can apply Stefan's x86 patch series on top of this. (I >>>>>>> cannot send PR for x86 before the usb changes) >>>>>> >>>>>> I actually cannot because the USB is currently broken, sorry, I'm >>>>>> waiting for a fix before I do that. >>>>>> >>>>>> Stefan, can you look at this series please? >>>>> >>>>> What "broken" issues are you seeing? >>>> >>>> I think Layerscape stopped building. Look at email with this subject >>>> "Compile failure encountered on latest (2017-07-20) >>>> git://git.denx.de/u-boot-usb.git branch master for target >>>> ls1021atwr_nor_defconfig" >>> >>> I see Patrice is working on a fix for the build failure. >> >> Correct, it's almost done. Sorry for the delay. > > FYI, since it was reported by Ran this series has some issues on NXP > LS1021ATWR, I will need allocate some time to figure out why. > > BTW: when will the u-boot-usb PR be sent? Not for any push, but > Stefan's x86 patches are in the x86 repo which depends on contents on > u-boot-usb and lots of Kconfig was changed in u-boot/master. The > longer time our patches are staying off stream, the more chances we > get rebase conflicts.
Today-ish . -- Best regards, Marek Vasut _______________________________________________ U-Boot mailing list [email protected] https://lists.denx.de/listinfo/u-boot
