From: Jeff Westfahl <[email protected]> In legacy method, FSBL was used to configure the HW setting such as NAND timing. Hence, adding a config option in Zynq NAND driver for the compability of device that using FSBL instead of U-boot SPL.
This commit is to add config option CONFIG_NAND_ZYNQ_USE_FSBL_TIMINGS that allow NAND driver use timing values set by the FSBL, instead of the hard-coded values in the Zynq NAND driver. Signed-off-by: Jeff Westfahl <[email protected]> Signed-off-by: Wilson Lee <[email protected]> Cc: Joe Hershberger <[email protected]> Cc: Keng Soon Cheah <[email protected]> Cc: Chen Yee Chew <[email protected]> Cc: Siva Durga Prasad Paladugu <[email protected]> Cc: Michal Simek <[email protected]> Cc: Scott Wood <[email protected]> --- drivers/mtd/nand/Kconfig | 6 ++++++ drivers/mtd/nand/zynq_nand.c | 5 +++++ 2 files changed, 11 insertions(+) diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index 71d678f..44d6aa0 100644 --- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -121,6 +121,12 @@ config NAND_ZYNQ This enables Nand driver support for Nand flash controller found on Zynq SoC. +config NAND_ZYNQ_USE_FSBL_TIMINGS + bool "Enable use of FSBL timing for NAND" + depends on NAND_ZYNQ + help + This enabled the use of FSBL timing for NAND flash controller. + comment "Generic NAND options" # Enhance depends when converting drivers to Kconfig which use this config diff --git a/drivers/mtd/nand/zynq_nand.c b/drivers/mtd/nand/zynq_nand.c index 484f1bb..f292531 100644 --- a/drivers/mtd/nand/zynq_nand.c +++ b/drivers/mtd/nand/zynq_nand.c @@ -35,6 +35,8 @@ (0x1 << 4) | /* Clear interrupt */ \ (0x1 << 6)) /* Disable ECC interrupt */ +#ifndef CONFIG_NAND_ZYNQ_USE_FSBL_TIMINGS + /* Assuming 50MHz clock (20ns cycle time) and 3V operation */ #define ZYNQ_NAND_SET_CYCLES ((0x2 << 20) | /* t_rr from nand_cycles */ \ (0x2 << 17) | /* t_ar from nand_cycles */ \ @@ -43,6 +45,7 @@ (0x2 << 8) | /* t_rea from nand_cycles */ \ (0x5 << 4) | /* t_wc from nand_cycles */ \ (0x5 << 0)) /* t_rc from nand_cycles */ +#endif #define ZYNQ_NAND_DIRECT_CMD ((0x4 << 23) | /* Chip 0 from interface 1 */ \ @@ -257,8 +260,10 @@ static int zynq_nand_init_nand_flash(int option) /* disable interrupts */ writel(ZYNQ_NAND_CLR_CONFIG, &zynq_nand_smc_base->cfr); +#ifndef CONFIG_NAND_ZYNQ_USE_FSBL_TIMINGS /* Initialize the NAND interface by setting cycles and operation mode */ writel(ZYNQ_NAND_SET_CYCLES, &zynq_nand_smc_base->scr); +#endif if (option & NAND_BUSWIDTH_16) writel(ZYNQ_NAND_SET_OPMODE_16BIT, &zynq_nand_smc_base->sor); else -- 2.7.4 _______________________________________________ U-Boot mailing list [email protected] https://lists.denx.de/listinfo/u-boot
