Synchronize the Amlogic ARM64 dts from mainline Linux 4.13.5
In the preparation of the support of the Amlogic P212 board,
import the corresponding meson-gxl-s905x-p212.dts file.
Signed-off-by: Neil Armstrong <narmstr...@baylibre.com>
---
arch/arm/dts/Makefile | 3 +-
arch/arm/dts/meson-gx.dtsi | 13 +-
arch/arm/dts/meson-gxbb-odroidc2.dts | 108 ++---
arch/arm/dts/meson-gxbb.dtsi | 220 +++++++----
arch/arm/dts/meson-gxl-mali.dtsi | 43 ++
arch/arm/dts/meson-gxl-s905x-p212.dts | 95 +++++
arch/arm/dts/meson-gxl-s905x-p212.dtsi | 173 ++++++++
arch/arm/dts/meson-gxl-s905x.dtsi | 55 +++
arch/arm/dts/meson-gxl.dtsi | 628 ++++++++++++++++++++++++++++++
include/dt-bindings/gpio/meson-gxl-gpio.h | 131 +++++++
10 files changed, 1326 insertions(+), 143 deletions(-)
create mode 100644 arch/arm/dts/meson-gxl-mali.dtsi
create mode 100644 arch/arm/dts/meson-gxl-s905x-p212.dts
create mode 100644 arch/arm/dts/meson-gxl-s905x-p212.dtsi
create mode 100644 arch/arm/dts/meson-gxl-s905x.dtsi
create mode 100644 arch/arm/dts/meson-gxl.dtsi
create mode 100644 include/dt-bindings/gpio/meson-gxl-gpio.h
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 5b90280..8a07f53 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -54,7 +54,8 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rk3399-puma-ddr1866.dtb \
rv1108-evb.dtb
dtb-$(CONFIG_ARCH_MESON) += \
- meson-gxbb-odroidc2.dtb
+ meson-gxbb-odroidc2.dtb \
+ meson-gxl-s905x-p212.dtb
dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
tegra20-medcom-wide.dtb \
tegra20-paz00.dtb \
diff --git a/arch/arm/dts/meson-gx.dtsi b/arch/arm/dts/meson-gx.dtsi
index 436b875..738ed68 100644
--- a/arch/arm/dts/meson-gx.dtsi
+++ b/arch/arm/dts/meson-gx.dtsi
@@ -200,7 +200,7 @@
};
scpi_sensors: sensors {
- compatible = "arm,scpi-sensors";
+ compatible = "amlogic,meson-gxbb-scpi-sensors",
"arm,scpi-sensors";
#thermal-sensor-cells = <1>;
};
};
@@ -304,6 +304,15 @@
status = "disabled";
};
+ spicc: spi@8d80 {
+ compatible = "amlogic,meson-gx-spicc";
+ reg = <0x0 0x08d80 0x0 0x80>;
+ interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
spifc: spi@8c80 {
compatible = "amlogic,meson-gx-spifc",
"amlogic,meson-gxbb-spifc";
reg = <0x0 0x08c80 0x0 0x80>;
@@ -391,7 +400,7 @@
};
pwm_AO_ab: pwm@550 {
- compatible = "amlogic,meson-gx-pwm",
"amlogic,meson-gxbb-pwm";
+ compatible = "amlogic,meson-gx-ao-pwm",
"amlogic,meson-gxbb-ao-pwm";
reg = <0x0 0x00550 0x0 0x10>;
#pwm-cells = <3>;
status = "disabled";
diff --git a/arch/arm/dts/meson-gxbb-odroidc2.dts
b/arch/arm/dts/meson-gxbb-odroidc2.dts
index 54a9c6a..d147c85 100644
--- a/arch/arm/dts/meson-gxbb-odroidc2.dts
+++ b/arch/arm/dts/meson-gxbb-odroidc2.dts
@@ -137,16 +137,6 @@
};
};
-&scpi_clocks {
- status = "disabled";
-};
-
-&uart_AO {
- status = "okay";
- pinctrl-0 = <&uart_ao_a_pins>;
- pinctrl-names = "default";
-};
-
ðmac {
status = "okay";
pinctrl-0 = <ð_rgmii_pins>;
@@ -172,6 +162,33 @@
};
};
+&gpio_ao {
+ /*
+ * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
+ * to be turned high in order to be detected by the USB Controller
+ * This signal should be handled by a USB specific power sequence
+ * in order to reset the Hub when USB bus is powered down.
+ */
+ usb-hub {
+ gpio-hog;
+ gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb-hub-reset";
+ };
+};
+
+&i2c_A {
+ status = "okay";
+ pinctrl-0 = <&i2c_a_pins>;
+ pinctrl-names = "default";
+};
+
+&ir {
+ status = "okay";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+};
+
&pinctrl_aobus {
gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En",
"USB HUB nRESET", "USB OTG Power En",
@@ -223,55 +240,15 @@
"";
};
-&ir {
- status = "okay";
- pinctrl-0 = <&remote_input_ao_pins>;
- pinctrl-names = "default";
-};
-
-&i2c_A {
- status = "okay";
- pinctrl-0 = <&i2c_a_pins>;
- pinctrl-names = "default";
-};
-
-&gpio_ao {
- /*
- * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
- * to be turned high in order to be detected by the USB Controller
- * This signal should be handled by a USB specific power sequence
- * in order to reset the Hub when USB bus is powered down.
- */
- usb-hub {
- gpio-hog;
- gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
- output-high;
- line-name = "usb-hub-reset";
- };
-};
-
-&usb0_phy {
- status = "okay";
- phy-supply = <&usb_otg_pwr>;
-};
-
-&usb1_phy {
- status = "okay";
-};
-
-&usb0 {
- status = "okay";
-};
-
-&usb1 {
- status = "okay";
-};
-
&saradc {
status = "okay";
vref-supply = <&vcc1v8>;
};
+&scpi_clocks {
+ status = "disabled";
+};
+
/* SD */
&sd_emmc_b {
status = "okay";
@@ -309,3 +286,26 @@
vmmc-supply = <&vcc3v3>;
vqmmc-supply = <&vcc1v8>;
};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb0_phy {
+ status = "okay";
+ phy-supply = <&usb_otg_pwr>;
+};
+
+&usb1_phy {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
diff --git a/arch/arm/dts/meson-gxbb.dtsi b/arch/arm/dts/meson-gxbb.dtsi
index 86105a6..17d3efd 100644
--- a/arch/arm/dts/meson-gxbb.dtsi
+++ b/arch/arm/dts/meson-gxbb.dtsi
@@ -97,13 +97,6 @@
};
};
-ðmac {
- clocks = <&clkc CLKID_ETH>,
- <&clkc CLKID_FCLK_DIV2>,
- <&clkc CLKID_MPLL2>;
- clock-names = "stmmaceth", "clkin0", "clkin1";
-};
-
&aobus {
pinctrl_aobus: pinctrl@14 {
compatible = "amlogic,meson-gxbb-aobus-pinctrl";
@@ -249,9 +242,119 @@
function = "spdif_out_ao";
};
};
+
+ ao_cec_pins: ao_cec {
+ mux {
+ groups = "ao_cec";
+ function = "cec_ao";
+ };
+ };
+
+ ee_cec_pins: ee_cec {
+ mux {
+ groups = "ee_cec";
+ function = "cec_ao";
+ };
+ };
+ };
+};
+
+&apb {
+ mali: gpu@c0000 {
+ compatible = "amlogic,meson-gxbb-mali", "arm,mali-450";
+ reg = <0x0 0xc0000 0x0 0x40000>;
+ interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "gp", "gpmmu", "pp", "pmu",
+ "pp0", "ppmmu0", "pp1", "ppmmu1",
+ "pp2", "ppmmu2";
+ clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_MALI>;
+ clock-names = "bus", "core";
+
+ /*
+ * Mali clocking is provided by two identical clock paths
+ * MALI_0 and MALI_1 muxed to a single clock by a glitch
+ * free mux to safely change frequency while running.
+ */
+ assigned-clocks = <&clkc CLKID_MALI_0_SEL>,
+ <&clkc CLKID_MALI_0>,
+ <&clkc CLKID_MALI>; /* Glitch free mux */
+ assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>,
+ <0>, /* Do Nothing */
+ <&clkc CLKID_MALI_0>;
+ assigned-clock-rates = <0>, /* Do Nothing */
+ <666666666>,
+ <0>; /* Do Nothing */
+ };
+};
+
+&cbus {
+ spifc: spi@8c80 {
+ compatible = "amlogic,meson-gxbb-spifc";
+ reg = <0x0 0x08c80 0x0 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&clkc CLKID_SPI>;
+ status = "disabled";
+ };
+};
+
+ðmac {
+ clocks = <&clkc CLKID_ETH>,
+ <&clkc CLKID_FCLK_DIV2>,
+ <&clkc CLKID_MPLL2>;
+ clock-names = "stmmaceth", "clkin0", "clkin1";
+};
+
+&hdmi_tx {
+ compatible = "amlogic,meson-gxbb-dw-hdmi", "amlogic,meson-gx-dw-hdmi";
+ resets = <&reset RESET_HDMITX_CAPB3>,
+ <&reset RESET_HDMI_SYSTEM_RESET>,
+ <&reset RESET_HDMI_TX>;
+ reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy";
+ clocks = <&clkc CLKID_HDMI_PCLK>,
+ <&clkc CLKID_CLK81>,
+ <&clkc CLKID_GCLK_VENCI_INT0>;
+ clock-names = "isfr", "iahb", "venci";
+};
+
+&hiubus {
+ clkc: clock-controller@0 {
+ compatible = "amlogic,gxbb-clkc";
+ #clock-cells = <1>;
+ reg = <0x0 0x0 0x0 0x3db>;
};
};
+&hwrng {
+ clocks = <&clkc CLKID_RNG0>;
+ clock-names = "core";
+};
+
+&i2c_A {
+ clocks = <&clkc CLKID_I2C>;
+};
+
+&i2c_AO {
+ clocks = <&clkc CLKID_AO_I2C>;
+};
+
+&i2c_B {
+ clocks = <&clkc CLKID_I2C>;
+};
+
+&i2c_C {
+ clocks = <&clkc CLKID_I2C>;
+};
+
&periphs {
pinctrl_periphs: pinctrl@4b0 {
compatible = "amlogic,meson-gxbb-periphs-pinctrl";
@@ -262,7 +365,7 @@
gpio: bank@4b0 {
reg = <0x0 0x004b0 0x0 0x28>,
<0x0 0x004e8 0x0 0x14>,
- <0x0 0x00120 0x0 0x14>,
+ <0x0 0x00520 0x0 0x14>,
<0x0 0x00430 0x0 0x40>;
reg-names = "mux", "pull", "pull-enable", "gpio";
gpio-controller;
@@ -290,6 +393,22 @@
};
};
+ spi_pins: spi {
+ mux {
+ groups = "spi_miso",
+ "spi_mosi",
+ "spi_sclk";
+ function = "spi";
+ };
+ };
+
+ spi_ss0_pins: spi-ss0 {
+ mux {
+ groups = "spi_ss0";
+ function = "spi";
+ };
+ };
+
sdcard_pins: sdcard {
mux {
groups = "sdcard_d0",
@@ -521,67 +640,6 @@
};
};
-&hiubus {
- clkc: clock-controller@0 {
- compatible = "amlogic,gxbb-clkc";
- #clock-cells = <1>;
- reg = <0x0 0x0 0x0 0x3db>;
- };
-};
-
-&apb {
- mali: gpu@c0000 {
- compatible = "amlogic,meson-gxbb-mali", "arm,mali-450";
- reg = <0x0 0xc0000 0x0 0x40000>;
- interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "gp", "gpmmu", "pp", "pmu",
- "pp0", "ppmmu0", "pp1", "ppmmu1",
- "pp2", "ppmmu2";
- clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_MALI>;
- clock-names = "bus", "core";
-
- /*
- * Mali clocking is provided by two identical clock paths
- * MALI_0 and MALI_1 muxed to a single clock by a glitch
- * free mux to safely change frequency while running.
- */
- assigned-clocks = <&clkc CLKID_MALI_0_SEL>,
- <&clkc CLKID_MALI_0>,
- <&clkc CLKID_MALI>; /* Glitch free mux */
- assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>,
- <0>, /* Do Nothing */
- <&clkc CLKID_MALI_0>;
- assigned-clock-rates = <0>, /* Do Nothing */
- <666666666>,
- <0>; /* Do Nothing */
- };
-};
-
-&i2c_A {
- clocks = <&clkc CLKID_I2C>;
-};
-
-&i2c_AO {
- clocks = <&clkc CLKID_AO_I2C>;
-};
-
-&i2c_B {
- clocks = <&clkc CLKID_I2C>;
-};
-
-&i2c_C {
- clocks = <&clkc CLKID_I2C>;
-};
-
&saradc {
compatible = "amlogic,meson-gxbb-saradc", "amlogic,meson-saradc";
clocks = <&xtal>,
@@ -613,6 +671,13 @@
clock-names = "core", "clkin0", "clkin1";
};
+&spicc {
+ clocks = <&clkc CLKID_SPICC>;
+ clock-names = "core";
+ resets = <&reset RESET_PERIPHS_SPICC>;
+ num-cs = <1>;
+};
+
&spifc {
clocks = <&clkc CLKID_SPI>;
};
@@ -620,20 +685,3 @@
&vpu {
compatible = "amlogic,meson-gxbb-vpu", "amlogic,meson-gx-vpu";
};
-
-&hwrng {
- clocks = <&clkc CLKID_RNG0>;
- clock-names = "core";
-};
-
-&hdmi_tx {
- compatible = "amlogic,meson-gxbb-dw-hdmi", "amlogic,meson-gx-dw-hdmi";
- resets = <&reset RESET_HDMITX_CAPB3>,
- <&reset RESET_HDMI_SYSTEM_RESET>,
- <&reset RESET_HDMI_TX>;
- reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy";
- clocks = <&clkc CLKID_HDMI_PCLK>,
- <&clkc CLKID_CLK81>,
- <&clkc CLKID_GCLK_VENCI_INT0>;
- clock-names = "isfr", "iahb", "venci";
-};
diff --git a/arch/arm/dts/meson-gxl-mali.dtsi b/arch/arm/dts/meson-gxl-mali.dtsi
new file mode 100644
index 0000000..f06cc23
--- /dev/null
+++ b/arch/arm/dts/meson-gxl-mali.dtsi
@@ -0,0 +1,43 @@
+/*
+ * Copyright (c) 2017 BayLibre SAS
+ * Author: Neil Armstrong <narmstr...@baylibre.com>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+&apb {
+ mali: gpu@c0000 {
+ compatible = "amlogic,meson-gxbb-mali", "arm,mali-450";
+ reg = <0x0 0xc0000 0x0 0x40000>;
+ interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "gp", "gpmmu", "pp", "pmu",
+ "pp0", "ppmmu0", "pp1", "ppmmu1",
+ "pp2", "ppmmu2";
+ clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_MALI>;
+ clock-names = "bus", "core";
+
+ /*
+ * Mali clocking is provided by two identical clock paths
+ * MALI_0 and MALI_1 muxed to a single clock by a glitch
+ * free mux to safely change frequency while running.
+ */
+ assigned-clocks = <&clkc CLKID_MALI_0_SEL>,
+ <&clkc CLKID_MALI_0>,
+ <&clkc CLKID_MALI>; /* Glitch free mux */
+ assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>,
+ <0>, /* Do Nothing */
+ <&clkc CLKID_MALI_0>;
+ assigned-clock-rates = <0>, /* Do Nothing */
+ <666666666>,
+ <0>; /* Do Nothing */
+ };
+};
diff --git a/arch/arm/dts/meson-gxl-s905x-p212.dts
b/arch/arm/dts/meson-gxl-s905x-p212.dts
new file mode 100644
index 0000000..6ab17c1
--- /dev/null
+++ b/arch/arm/dts/meson-gxl-s905x-p212.dts
@@ -0,0 +1,95 @@
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <ca...@endlessm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "meson-gxl-s905x-p212.dtsi"
+
+/ {
+ compatible = "amlogic,p212", "amlogic,s905x", "amlogic,meson-gxl";
+ model = "Amlogic Meson GXL (S905X) P212 Development Board";
+
+ cvbs-connector {
+ compatible = "composite-video-connector";
+
+ port {
+ cvbs_connector_in: endpoint {
+ remote-endpoint = <&cvbs_vdac_out>;
+ };
+ };
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+};
+
+&cvbs_vdac_port {
+ cvbs_vdac_out: endpoint {
+ remote-endpoint = <&cvbs_connector_in>;
+ };
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+ pinctrl-names = "default";
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
+/* This UART is brought out to the DB9 connector */
+&uart_AO {
+ status = "okay";
+};
diff --git a/arch/arm/dts/meson-gxl-s905x-p212.dtsi
b/arch/arm/dts/meson-gxl-s905x-p212.dtsi
new file mode 100644
index 0000000..f3eea8e
--- /dev/null
+++ b/arch/arm/dts/meson-gxl-s905x-p212.dtsi
@@ -0,0 +1,173 @@
+/*
+ * Copyright (c) 2016 Martin Blumenstingl <martin.blumensti...@googlemail.com>.
+ * Based on meson-gx-p23x-q20x.dtsi:
+ * - Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <ca...@endlessm.com>
+ * - Copyright (c) 2016 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstr...@baylibre.com>
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+/* Common DTSI for devices which are based on the P212 reference board. */
+
+#include "meson-gxl-s905x.dtsi"
+
+/ {
+ aliases {
+ serial0 = &uart_AO;
+ serial1 = &uart_A;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ vddio_boot: regulator-vddio_boot {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_BOOT";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vddio_ao18: regulator-vddio_ao18 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi32k: wifi32k {
+ compatible = "pwm-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+ clocks = <&wifi32k>;
+ clock-names = "ext_clock";
+ };
+};
+
+ðmac {
+ status = "okay";
+};
+
+&ir {
+ status = "okay";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+ status = "okay";
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <100000000>;
+
+ non-removable;
+ disable-wp;
+
+ mmc-pwrseq = <&sdio_pwrseq>;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_pins>;
+ pinctrl-names = "default";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <100000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+ cd-inverted;
+
+ vmmc-supply = <&vddao_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>;
+ pinctrl-names = "default";
+
+ bus-width = <8>;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ max-frequency = <200000000>;
+ non-removable;
+ disable-wp;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vddio_boot>;
+};
+
+&pwm_ef {
+ status = "okay";
+ pinctrl-0 = <&pwm_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&clkc CLKID_FCLK_DIV4>;
+ clock-names = "clkin0";
+};
+
+/* This is connected to the Bluetooth module: */
+&uart_A {
+ status = "okay";
+ pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
diff --git a/arch/arm/dts/meson-gxl-s905x.dtsi
b/arch/arm/dts/meson-gxl-s905x.dtsi
new file mode 100644
index 0000000..3314a0b
--- /dev/null
+++ b/arch/arm/dts/meson-gxl-s905x.dtsi
@@ -0,0 +1,55 @@
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <ca...@endlessm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "meson-gxl.dtsi"
+#include "meson-gxl-mali.dtsi"
+
+/ {
+ compatible = "amlogic,s905x", "amlogic,meson-gxl";
+};
+
+/* S905X only has access to its internal PHY */
+ðmac {
+ phy-mode = "rmii";
+ phy-handle = <&internal_phy>;
+};
diff --git a/arch/arm/dts/meson-gxl.dtsi b/arch/arm/dts/meson-gxl.dtsi
new file mode 100644
index 0000000..8d4f316
--- /dev/null
+++ b/arch/arm/dts/meson-gxl.dtsi
@@ -0,0 +1,628 @@
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <ca...@endlessm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "meson-gx.dtsi"
+#include <dt-bindings/clock/gxbb-clkc.h>
+#include <dt-bindings/gpio/meson-gxl-gpio.h>
+#include <dt-bindings/reset/amlogic,meson-gxbb-reset.h>
+
+/ {
+ compatible = "amlogic,meson-gxl";
+};
+
+ðmac {
+ reg = <0x0 0xc9410000 0x0 0x10000
+ 0x0 0xc8834540 0x0 0x4>;
+
+ clocks = <&clkc CLKID_ETH>,
+ <&clkc CLKID_FCLK_DIV2>,
+ <&clkc CLKID_MPLL2>;
+ clock-names = "stmmaceth", "clkin0", "clkin1";
+
+ mdio0: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ };
+};
+
+&aobus {
+ pinctrl_aobus: pinctrl@14 {
+ compatible = "amlogic,meson-gxl-aobus-pinctrl";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ gpio_ao: bank@14 {
+ reg = <0x0 0x00014 0x0 0x8>,
+ <0x0 0x0002c 0x0 0x4>,
+ <0x0 0x00024 0x0 0x8>;
+ reg-names = "mux", "pull", "gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pinctrl_aobus 0 0 14>;
+ };
+
+ uart_ao_a_pins: uart_ao_a {
+ mux {
+ groups = "uart_tx_ao_a", "uart_rx_ao_a";
+ function = "uart_ao";
+ };
+ };
+
+ uart_ao_a_cts_rts_pins: uart_ao_a_cts_rts {
+ mux {
+ groups = "uart_cts_ao_a",
+ "uart_rts_ao_a";
+ function = "uart_ao";
+ };
+ };
+
+ uart_ao_b_pins: uart_ao_b {
+ mux {
+ groups = "uart_tx_ao_b", "uart_rx_ao_b";
+ function = "uart_ao_b";
+ };
+ };
+
+ uart_ao_b_0_1_pins: uart_ao_b_0_1 {
+ mux {
+ groups = "uart_tx_ao_b_0", "uart_rx_ao_b_1";
+ function = "uart_ao_b";
+ };
+ };
+
+ uart_ao_b_cts_rts_pins: uart_ao_b_cts_rts {
+ mux {
+ groups = "uart_cts_ao_b",
+ "uart_rts_ao_b";
+ function = "uart_ao_b";
+ };
+ };
+
+ remote_input_ao_pins: remote_input_ao {
+ mux {
+ groups = "remote_input_ao";
+ function = "remote_input_ao";
+ };
+ };
+
+ i2c_ao_pins: i2c_ao {
+ mux {
+ groups = "i2c_sck_ao",
+ "i2c_sda_ao";
+ function = "i2c_ao";
+ };
+ };
+
+ pwm_ao_a_3_pins: pwm_ao_a_3 {
+ mux {
+ groups = "pwm_ao_a_3";
+ function = "pwm_ao_a";
+ };
+ };
+
+ pwm_ao_a_8_pins: pwm_ao_a_8 {
+ mux {
+ groups = "pwm_ao_a_8";
+ function = "pwm_ao_a";
+ };
+ };
+
+ pwm_ao_b_pins: pwm_ao_b {
+ mux {
+ groups = "pwm_ao_b";
+ function = "pwm_ao_b";
+ };
+ };
+
+ pwm_ao_b_6_pins: pwm_ao_b_6 {
+ mux {
+ groups = "pwm_ao_b_6";
+ function = "pwm_ao_b";
+ };
+ };
+
+ i2s_out_ch23_ao_pins: i2s_out_ch23_ao {
+ mux {
+ groups = "i2s_out_ch23_ao";
+ function = "i2s_out_ao";
+ };
+ };
+
+ i2s_out_ch45_ao_pins: i2s_out_ch45_ao {
+ mux {
+ groups = "i2s_out_ch45_ao";
+ function = "i2s_out_ao";
+ };
+ };
+
+ spdif_out_ao_6_pins: spdif_out_ao_6 {
+ mux {
+ groups = "spdif_out_ao_6";
+ function = "spdif_out_ao";
+ };
+ };
+
+ spdif_out_ao_9_pins: spdif_out_ao_9 {
+ mux {
+ groups = "spdif_out_ao_9";
+ function = "spdif_out_ao";
+ };
+ };
+
+ ao_cec_pins: ao_cec {
+ mux {
+ groups = "ao_cec";
+ function = "cec_ao";
+ };
+ };
+
+ ee_cec_pins: ee_cec {
+ mux {
+ groups = "ee_cec";
+ function = "cec_ao";
+ };
+ };
+ };
+};
+
+&hdmi_tx {
+ compatible = "amlogic,meson-gxl-dw-hdmi", "amlogic,meson-gx-dw-hdmi";
+ resets = <&reset RESET_HDMITX_CAPB3>,
+ <&reset RESET_HDMI_SYSTEM_RESET>,
+ <&reset RESET_HDMI_TX>;
+ reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy";
+ clocks = <&clkc CLKID_HDMI_PCLK>,
+ <&clkc CLKID_CLK81>,
+ <&clkc CLKID_GCLK_VENCI_INT0>;
+ clock-names = "isfr", "iahb", "venci";
+};
+
+&hiubus {
+ clkc: clock-controller@0 {
+ compatible = "amlogic,gxl-clkc", "amlogic,gxbb-clkc";
+ #clock-cells = <1>;
+ reg = <0x0 0x0 0x0 0x3db>;
+ };
+};
+
+&i2c_A {
+ clocks = <&clkc CLKID_I2C>;
+};
+
+&i2c_AO {
+ clocks = <&clkc CLKID_AO_I2C>;
+};
+
+&i2c_B {
+ clocks = <&clkc CLKID_I2C>;
+};
+
+&i2c_C {
+ clocks = <&clkc CLKID_I2C>;
+};
+
+&periphs {
+ pinctrl_periphs: pinctrl@4b0 {
+ compatible = "amlogic,meson-gxl-periphs-pinctrl";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ gpio: bank@4b0 {
+ reg = <0x0 0x004b0 0x0 0x28>,
+ <0x0 0x004e8 0x0 0x14>,
+ <0x0 0x00520 0x0 0x14>,
+ <0x0 0x00430 0x0 0x40>;
+ reg-names = "mux", "pull", "pull-enable", "gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pinctrl_periphs 0 10 101>;
+ };
+
+ emmc_pins: emmc {
+ mux {
+ groups = "emmc_nand_d07",
+ "emmc_cmd",
+ "emmc_clk",
+ "emmc_ds";
+ function = "emmc";
+ };
+ };
+
+ nor_pins: nor {
+ mux {
+ groups = "nor_d",
+ "nor_q",
+ "nor_c",
+ "nor_cs";
+ function = "nor";
+ };
+ };
+
+ spi_pins: spi {
+ mux {
+ groups = "spi_miso",
+ "spi_mosi",
+ "spi_sclk";
+ function = "spi";
+ };
+ };
+
+ spi_ss0_pins: spi-ss0 {
+ mux {
+ groups = "spi_ss0";
+ function = "spi";
+ };
+ };
+
+ sdcard_pins: sdcard {
+ mux {
+ groups = "sdcard_d0",
+ "sdcard_d1",
+ "sdcard_d2",
+ "sdcard_d3",
+ "sdcard_cmd",
+ "sdcard_clk";
+ function = "sdcard";
+ };
+ };
+
+ sdio_pins: sdio {
+ mux {
+ groups = "sdio_d0",
+ "sdio_d1",
+ "sdio_d2",
+ "sdio_d3",
+ "sdio_cmd",
+ "sdio_clk";
+ function = "sdio";
+ };
+ };
+
+ sdio_irq_pins: sdio_irq {
+ mux {
+ groups = "sdio_irq";
+ function = "sdio";
+ };
+ };
+
+ uart_a_pins: uart_a {
+ mux {
+ groups = "uart_tx_a",
+ "uart_rx_a";
+ function = "uart_a";
+ };
+ };
+
+ uart_a_cts_rts_pins: uart_a_cts_rts {
+ mux {
+ groups = "uart_cts_a",
+ "uart_rts_a";
+ function = "uart_a";
+ };
+ };
+
+ uart_b_pins: uart_b {
+ mux {
+ groups = "uart_tx_b",
+ "uart_rx_b";
+ function = "uart_b";
+ };
+ };
+
+ uart_b_cts_rts_pins: uart_b_cts_rts {
+ mux {
+ groups = "uart_cts_b",
+ "uart_rts_b";
+ function = "uart_b";
+ };
+ };
+
+ uart_c_pins: uart_c {
+ mux {
+ groups = "uart_tx_c",
+ "uart_rx_c";
+ function = "uart_c";
+ };
+ };
+
+ uart_c_cts_rts_pins: uart_c_cts_rts {
+ mux {
+ groups = "uart_cts_c",
+ "uart_rts_c";
+ function = "uart_c";
+ };
+ };
+
+ i2c_a_pins: i2c_a {
+ mux {
+ groups = "i2c_sck_a",
+ "i2c_sda_a";
+ function = "i2c_a";
+ };
+ };
+
+ i2c_b_pins: i2c_b {
+ mux {
+ groups = "i2c_sck_b",
+ "i2c_sda_b";
+ function = "i2c_b";
+ };
+ };
+
+ i2c_c_pins: i2c_c {
+ mux {
+ groups = "i2c_sck_c",
+ "i2c_sda_c";
+ function = "i2c_c";
+ };
+ };
+
+ eth_pins: eth_c {
+ mux {
+ groups = "eth_mdio",
+ "eth_mdc",
+ "eth_clk_rx_clk",
+ "eth_rx_dv",
+ "eth_rxd0",
+ "eth_rxd1",
+ "eth_rxd2",
+ "eth_rxd3",
+ "eth_rgmii_tx_clk",
+ "eth_tx_en",
+ "eth_txd0",
+ "eth_txd1",
+ "eth_txd2",
+ "eth_txd3";
+ function = "eth";
+ };
+ };
+
+ eth_link_led_pins: eth_link_led {
+ mux {
+ groups = "eth_link_led";
+ function = "eth_led";
+ };
+ };
+
+ eth_act_led_pins: eth_act_led {
+ mux {
+ groups = "eth_act_led";
+ function = "eth_led";
+ };
+ };
+
+ pwm_a_pins: pwm_a {
+ mux {
+ groups = "pwm_a";
+ function = "pwm_a";
+ };
+ };
+
+ pwm_b_pins: pwm_b {
+ mux {
+ groups = "pwm_b";
+ function = "pwm_b";
+ };
+ };
+
+ pwm_c_pins: pwm_c {
+ mux {
+ groups = "pwm_c";
+ function = "pwm_c";
+ };
+ };
+
+ pwm_d_pins: pwm_d {
+ mux {
+ groups = "pwm_d";
+ function = "pwm_d";
+ };
+ };
+
+ pwm_e_pins: pwm_e {
+ mux {
+ groups = "pwm_e";
+ function = "pwm_e";
+ };
+ };
+
+ pwm_f_clk_pins: pwm_f_clk {
+ mux {
+ groups = "pwm_f_clk";
+ function = "pwm_f";
+ };
+ };
+
+ pwm_f_x_pins: pwm_f_x {
+ mux {
+ groups = "pwm_f_x";
+ function = "pwm_f";
+ };
+ };
+
+ hdmi_hpd_pins: hdmi_hpd {
+ mux {
+ groups = "hdmi_hpd";
+ function = "hdmi_hpd";
+ };
+ };
+
+ hdmi_i2c_pins: hdmi_i2c {
+ mux {
+ groups = "hdmi_sda", "hdmi_scl";
+ function = "hdmi_i2c";
+ };
+ };
+
+ i2s_am_clk_pins: i2s_am_clk {
+ mux {
+ groups = "i2s_am_clk";
+ function = "i2s_out";
+ };
+ };
+
+ i2s_out_ao_clk_pins: i2s_out_ao_clk {
+ mux {
+ groups = "i2s_out_ao_clk";
+ function = "i2s_out";
+ };
+ };
+
+ i2s_out_lr_clk_pins: i2s_out_lr_clk {
+ mux {
+ groups = "i2s_out_lr_clk";
+ function = "i2s_out";
+ };
+ };
+
+ i2s_out_ch01_pins: i2s_out_ch01 {
+ mux {
+ groups = "i2s_out_ch01";
+ function = "i2s_out";
+ };
+ };
+ i2sout_ch23_z_pins: i2sout_ch23_z {
+ mux {
+ groups = "i2sout_ch23_z";
+ function = "i2s_out";
+ };
+ };
+
+ i2sout_ch45_z_pins: i2sout_ch45_z {
+ mux {
+ groups = "i2sout_ch45_z";
+ function = "i2s_out";
+ };
+ };
+
+ i2sout_ch67_z_pins: i2sout_ch67_z {
+ mux {
+ groups = "i2sout_ch67_z";
+ function = "i2s_out";
+ };
+ };
+
+ spdif_out_h_pins: spdif_out_ao_h {
+ mux {
+ groups = "spdif_out_h";
+ function = "spdif_out";
+ };
+ };
+ };
+
+ eth-phy-mux {
+ compatible = "mdio-mux-mmioreg", "mdio-mux";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x55c 0x0 0x4>;
+ mux-mask = <0xffffffff>;
+ mdio-parent-bus = <&mdio0>;
+
+ internal_mdio: mdio@e40908ff {
+ reg = <0xe40908ff>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ internal_phy: ethernet-phy@8 {
+ compatible = "ethernet-phy-id0181.4400",
"ethernet-phy-ieee802.3-c22";
+ reg = <8>;
+ max-speed = <100>;
+ };
+ };
+
+ external_mdio: mdio@2009087f {
+ reg = <0x2009087f>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+};
+
+&saradc {
+ compatible = "amlogic,meson-gxl-saradc", "amlogic,meson-saradc";
+ clocks = <&xtal>,
+ <&clkc CLKID_SAR_ADC>,
+ <&clkc CLKID_SANA>,
+ <&clkc CLKID_SAR_ADC_CLK>,
+ <&clkc CLKID_SAR_ADC_SEL>;
+ clock-names = "clkin", "core", "sana", "adc_clk", "adc_sel";
+};
+
+&sd_emmc_a {
+ clocks = <&clkc CLKID_SD_EMMC_A>,
+ <&xtal>,
+ <&clkc CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+};
+
+&sd_emmc_b {
+ clocks = <&clkc CLKID_SD_EMMC_B>,
+ <&xtal>,
+ <&clkc CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+};
+
+&sd_emmc_c {
+ clocks = <&clkc CLKID_SD_EMMC_C>,
+ <&xtal>,
+ <&clkc CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+};
+
+&spicc {
+ clocks = <&clkc CLKID_SPICC>;
+ clock-names = "core";
+ resets = <&reset RESET_PERIPHS_SPICC>;
+ num-cs = <1>;
+};
+
+&spifc {
+ clocks = <&clkc CLKID_SPI>;
+};
+
+&vpu {
+ compatible = "amlogic,meson-gxl-vpu", "amlogic,meson-gx-vpu";
+};
diff --git a/include/dt-bindings/gpio/meson-gxl-gpio.h
b/include/dt-bindings/gpio/meson-gxl-gpio.h
new file mode 100644
index 0000000..684d0d7
--- /dev/null
+++ b/include/dt-bindings/gpio/meson-gxl-gpio.h
@@ -0,0 +1,131 @@
+/*
+ * GPIO definitions for Amlogic Meson GXL SoCs
+ *
+ * Copyright (C) 2016 Endless Mobile, Inc.
+ * Author: Carlo Caione <ca...@endlessm.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _DT_BINDINGS_MESON_GXL_GPIO_H
+#define _DT_BINDINGS_MESON_GXL_GPIO_H
+
+#define GPIOAO_0 0
+#define GPIOAO_1 1
+#define GPIOAO_2 2
+#define GPIOAO_3 3
+#define GPIOAO_4 4
+#define GPIOAO_5 5
+#define GPIOAO_6 6
+#define GPIOAO_7 7
+#define GPIOAO_8 8
+#define GPIOAO_9 9
+
+#define GPIOZ_0 0
+#define GPIOZ_1 1
+#define GPIOZ_2 2
+#define GPIOZ_3 3
+#define GPIOZ_4 4
+#define GPIOZ_5 5
+#define GPIOZ_6 6
+#define GPIOZ_7 7
+#define GPIOZ_8 8
+#define GPIOZ_9 9
+#define GPIOZ_10 10
+#define GPIOZ_11 11
+#define GPIOZ_12 12
+#define GPIOZ_13 13
+#define GPIOZ_14 14
+#define GPIOZ_15 15
+#define GPIOH_0 16
+#define GPIOH_1 17
+#define GPIOH_2 18
+#define GPIOH_3 19
+#define GPIOH_4 20
+#define GPIOH_5 21
+#define GPIOH_6 22
+#define GPIOH_7 23
+#define GPIOH_8 24
+#define GPIOH_9 25
+#define BOOT_0 26
+#define BOOT_1 27
+#define BOOT_2 28
+#define BOOT_3 29
+#define BOOT_4 30
+#define BOOT_5 31
+#define BOOT_6 32
+#define BOOT_7 33
+#define BOOT_8 34
+#define BOOT_9 35
+#define BOOT_10 36
+#define BOOT_11 37
+#define BOOT_12 38
+#define BOOT_13 39
+#define BOOT_14 40
+#define BOOT_15 41
+#define CARD_0 42
+#define CARD_1 43
+#define CARD_2 44
+#define CARD_3 45
+#define CARD_4 46
+#define CARD_5 47
+#define CARD_6 48
+#define GPIODV_0 49
+#define GPIODV_1 50
+#define GPIODV_2 51
+#define GPIODV_3 52
+#define GPIODV_4 53
+#define GPIODV_5 54
+#define GPIODV_6 55
+#define GPIODV_7 56
+#define GPIODV_8 57
+#define GPIODV_9 58
+#define GPIODV_10 59
+#define GPIODV_11 60
+#define GPIODV_12 61
+#define GPIODV_13 62
+#define GPIODV_14 63
+#define GPIODV_15 64
+#define GPIODV_16 65
+#define GPIODV_17 66
+#define GPIODV_18 67
+#define GPIODV_19 68
+#define GPIODV_20 69
+#define GPIODV_21 70
+#define GPIODV_22 71
+#define GPIODV_23 72
+#define GPIODV_24 73
+#define GPIODV_25 74
+#define GPIODV_26 75
+#define GPIODV_27 76
+#define GPIODV_28 77
+#define GPIODV_29 78
+#define GPIOX_0 79
+#define GPIOX_1 80
+#define GPIOX_2 81
+#define GPIOX_3 82
+#define GPIOX_4 83
+#define GPIOX_5 84
+#define GPIOX_6 85
+#define GPIOX_7 86
+#define GPIOX_8 87
+#define GPIOX_9 88
+#define GPIOX_10 89
+#define GPIOX_11 90
+#define GPIOX_12 91
+#define GPIOX_13 92
+#define GPIOX_14 93
+#define GPIOX_15 94
+#define GPIOX_16 95
+#define GPIOX_17 96
+#define GPIOX_18 97
+#define GPIOCLK_0 98
+#define GPIOCLK_1 99
+#define GPIO_TEST_N 100
+
+#endif
--
2.7.4
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
