On Fri, Nov 03, 2017 at 02:21:51PM +0530, Jagan Teki wrote: > On Thu, Nov 2, 2017 at 7:26 PM, Maxime Ripard > <[email protected]> wrote: > > On Wed, Nov 01, 2017 at 08:31:46AM +0800, Icenowy Zheng wrote: > >> 在 2017-10-31 21:54，Maxime Ripard 写道： > >> > On Tue, Oct 31, 2017 at 04:05:36PM +0800, [email protected] wrote: > >> > > 在 2017-10-31 15:57，Jagan Teki 写道： > >> > > > On Tue, Oct 31, 2017 at 5:06 AM, Icenowy Zheng <[email protected]> > >> > > > wrote: > >> > > > > Some H5 boards are designed to start at 1.1V CPUx voltage (e.g. > >> > > > > Nano > >> > > > > Pi > >> > > > > NEO2), which may not work properly at 1008MHz if the chip's > >> > > > > quality is > >> > > > > not so good. > >> > > > > > >> > > > > Lower the default CPUx frequency of H5 to 816MHz. > >> > > > > > >> > > > > Signed-off-by: Icenowy Zheng <[email protected]> > >> > > > > --- > >> > > > > arch/arm/mach-sunxi/Kconfig | 2 +- > >> > > > > 1 file changed, 1 insertion(+), 1 deletion(-) > >> > > > > > >> > > > > diff --git a/arch/arm/mach-sunxi/Kconfig > >> > > > > b/arch/arm/mach-sunxi/Kconfig > >> > > > > index 09cfec6f57..1fededd0a3 100644 > >> > > > > --- a/arch/arm/mach-sunxi/Kconfig > >> > > > > +++ b/arch/arm/mach-sunxi/Kconfig > >> > > > > @@ -397,9 +397,9 @@ config SYS_CLK_FREQ > >> > > > > default 1008000000 if MACH_SUN5I > >> > > > > default 1008000000 if MACH_SUN6I > >> > > > > default 912000000 if MACH_SUN7I > >> > > > > + default 816000000 if MACH_SUN50I || MACH_SUN50I_H5 > >> > > > > default 1008000000 if MACH_SUN8I > >> > > > > >> > > > Even orangepi pc2 has 1.1v after power-on and it's work fine [1] did > >> > > > you find an issue with neo2? > >> > > >> > So you have one single model that fails, and you change the default > >> > frequency of all the boards using that SoC? > >> > >> But I think we have already set the default frequency to 816MHz for > >> A64, and it seems that several H5 boards are designed to start at 1.1v > >> (see the notes by Jagan above). > >> > >> > > >> > It seems a bit overkill. > >> > > >> > I guess we have two solutions: > >> > 1) Change the frequency in that board config > >> > 2) Change the voltage in that board config > >> > >> NEO2 don't have any voltage adjusting, it's fixed at 1.1V. > >> > >> And according to the Orange Pi PC2 and Prime schematics, they both > >> start at 1.1V. (The Prime schematics even says "For H5 adjust > >> VDD-CPUX to 1.1V). > > > > And what about the Zero Plus 2 ? > > Same equation with same reg values, but missing reg names on specific > register area Page 7 [4] but hope both were same.
Ok, so it's not some H5 boards, it's all of them. It makes sense then, once the commit log has been changed. Maxime -- Maxime Ripard, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com
signature.asc
Description: PGP signature
_______________________________________________ U-Boot mailing list [email protected] https://lists.denx.de/listinfo/u-boot
