On 06/28/2018 09:26 PM, Grygorii Strashko wrote:
From: Murali Karicheri <[email protected]>
The data manual for DP83867IR/CR, SNLS484E[1], revised march 2017,
advises that strapping RX_DV/RX_CTRL pin in mode 1 and 2 is not
supported (see note below Table 5 (4-Level Strap Pins)).
It further advises that if a board has this pin strapped in mode 1 and
mode 2, then bit[7] of Configuration Register 4 (address 0x0031) must
be cleared to 0. This is to ensure proper operation of PHY.
Since it is not possible to detect in software if RX_DV/RX_CTRL pin is
incorrectly strapped, add a device-tree property to advertise this and
allow corrective action in software.
[1] http://www.ti.com/lit/ds/snls484e/snls484e.pdf
Signed-off-by: Murali Karicheri <[email protected]>
---
drivers/net/phy/ti.c | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/drivers/net/phy/ti.c b/drivers/net/phy/ti.c
index 8f3ed8a..f1c9f7b 100644
--- a/drivers/net/phy/ti.c
+++ b/drivers/net/phy/ti.c
@@ -24,6 +24,7 @@ DECLARE_GLOBAL_DATA_PTR;
#define DP83867_CTRL 0x1f
/* Extended Registers */
+#define DP83867_CFG4 0x0031
#define DP83867_RGMIICTL 0x0032
#define DP83867_RGMIIDCTL 0x0086
#define DP83867_IO_MUX_CFG 0x0170
@@ -95,6 +96,7 @@ struct dp83867_private {
int tx_id_delay;
int fifo_depth;
int io_impedance;
+ bool rxctrl_strap_quirk;
};
/**
@@ -183,6 +185,8 @@ static int dp83867_of_init(struct phy_device *phydev)
else
dp83867->io_impedance = -EINVAL;
+ if (fdtdec_get_bool(fdt, node, "ti,dp83867-rxctrl-strap-quirk"))
+ dp83867->rxctrl_strap_quirk = true;
dp83867->rx_id_delay = fdtdec_get_uint(gd->fdt_blob, dev_of_offset(dev),
"ti,rx-internal-delay", -1);
@@ -232,6 +236,15 @@ static int dp83867_config(struct phy_device *phydev)
phy_write(phydev, MDIO_DEVAD_NONE, DP83867_CTRL,
val | DP83867_SW_RESTART);
+ /* Mode 1 or 2 workaround */
+ if (dp83867->rxctrl_strap_quirk) {
+ val = phy_read_mmd_indirect(phydev, DP83867_CFG4,
+ DP83867_DEVADDR, phydev->addr);
+ val &= ~BIT(7);
+ phy_write_mmd_indirect(phydev, DP83867_CFG4,
+ DP83867_DEVADDR, phydev->addr, val);
+ }
+
if (phy_interface_is_rgmii(phydev)) {
ret = phy_write(phydev, MDIO_DEVAD_NONE, MII_DP83867_PHYCTRL,
(DP83867_MDI_CROSSOVER_AUTO << DP83867_MDI_CROSSOVER) |
Reviewed-by: Hannes Schmelzer <[email protected]>
_______________________________________________
U-Boot mailing list
[email protected]
https://lists.denx.de/listinfo/u-boot
