The cached RXQCR value is never updated, remove the cache and just use
the bits in the cache directly in the code.
Signed-off-by: Marek Vasut <ma...@denx.de>
Cc: Eugen Hristev <eugen.hris...@microchip.com>
Cc: Joe Hershberger <joe.hershber...@ni.com>
---
drivers/net/ks8851_mll.c | 15 ++++++---------
1 file changed, 6 insertions(+), 9 deletions(-)
diff --git a/drivers/net/ks8851_mll.c b/drivers/net/ks8851_mll.c
index 4386763bac..367ad2a397 100644
--- a/drivers/net/ks8851_mll.c
+++ b/drivers/net/ks8851_mll.c
@@ -49,7 +49,6 @@ union ks_tx_hdr {
* @frame_cnt : number of frames received.
* @bus_width : i/o bus width.
* @irq : irq number assigned to this device.
- * @rc_rxqcr : Cached copy of KS_RXQCR.
* @rc_txcr : Cached copy of KS_TXCR.
* @rc_ier : Cached copy of KS_IER.
* @sharedbus : Multipex(addr and data bus) mode indicator.
@@ -80,7 +79,6 @@ struct ks_net {
u32 frame_cnt;
int bus_width;
int irq;
- u16 rc_rxqcr;
u16 rc_txcr;
u16 rc_ier;
u16 sharedbus;
@@ -275,7 +273,7 @@ static inline void ks_read_qmu(struct eth_device *dev, u16
*buf, u32 len)
/* 1. set sudo DMA mode */
ks_wrreg16(dev, KS_RXFDPR, RXFDPR_RXFPAI);
- ks_wrreg8(dev, KS_RXQCR, (ks->rc_rxqcr | RXQCR_SDA) & 0xff);
+ ks_wrreg8(dev, KS_RXQCR, RXQCR_CMD_CNTL | RXQCR_SDA);
/*
* 2. read prepend data
@@ -293,7 +291,7 @@ static inline void ks_read_qmu(struct eth_device *dev, u16
*buf, u32 len)
ks_inblk(dev, buf, ALIGN(len, 4));
/* 4. reset sudo DMA Mode */
- ks_wrreg8(dev, KS_RXQCR, (ks->rc_rxqcr & ~RXQCR_SDA) & 0xff);
+ ks_wrreg8(dev, KS_RXQCR, RXQCR_CMD_CNTL);
}
static void ks_rcv(struct eth_device *dev, uchar **pv_data)
@@ -324,7 +322,7 @@ static void ks_rcv(struct eth_device *dev, uchar **pv_data)
net_process_received_packet(*pv_data, frame_hdr->len);
pv_data++;
} else {
- ks_wrreg16(dev, KS_RXQCR, (ks->rc_rxqcr | RXQCR_RRXEF));
+ ks_wrreg16(dev, KS_RXQCR, RXQCR_CMD_CNTL | RXQCR_RRXEF);
printf(DRIVERNAME ": bad packet\n");
}
frame_hdr++;
@@ -379,8 +377,7 @@ static void ks_setup(struct eth_device *dev)
ks_wrreg16(dev, KS_RXFCTR, 1 & RXFCTR_THRESHOLD_MASK);
/* Setup RxQ Command Control (RXQCR) */
- ks->rc_rxqcr = RXQCR_CMD_CNTL;
- ks_wrreg16(dev, KS_RXQCR, ks->rc_rxqcr);
+ ks_wrreg16(dev, KS_RXQCR, RXQCR_CMD_CNTL);
/*
* set the force mode to half duplex, default is full duplex
@@ -519,13 +516,13 @@ static void ks_write_qmu(struct eth_device *dev, u8
*pdata, u16 len)
/* 1. set sudo-DMA mode */
ks_wrreg16(dev, KS_TXFDPR, TXFDPR_TXFPAI);
- ks_wrreg8(dev, KS_RXQCR, (ks->rc_rxqcr | RXQCR_SDA) & 0xff);
+ ks_wrreg8(dev, KS_RXQCR, RXQCR_CMD_CNTL | RXQCR_SDA);
/* 2. write status/lenth info */
ks_outblk(dev, ks->txh.txw, 4);
/* 3. write pkt data */
ks_outblk(dev, (u16 *)pdata, ALIGN(len, 4));
/* 4. reset sudo-DMA mode */
- ks_wrreg8(dev, KS_RXQCR, (ks->rc_rxqcr & ~RXQCR_SDA) & 0xff);
+ ks_wrreg8(dev, KS_RXQCR, RXQCR_CMD_CNTL);
/* 5. Enqueue Tx(move the pkt from TX buffer into TXQ) */
ks_wrreg16(dev, KS_TXQCR, TXQCR_METFE);
/* 6. wait until TXQCR_METFE is auto-cleared */
--
2.25.1
