From: Igal Liberman <[email protected]>
Signed-off-by: Igal Liberman <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
---
doc/device-tree-bindings/phy/mvebu_comphy.txt | 68 +++++++++++++++++++
1 file changed, 68 insertions(+)
create mode 100644 doc/device-tree-bindings/phy/mvebu_comphy.txt
diff --git a/doc/device-tree-bindings/phy/mvebu_comphy.txt
b/doc/device-tree-bindings/phy/mvebu_comphy.txt
new file mode 100644
index 000000000000..65b83848596b
--- /dev/null
+++ b/doc/device-tree-bindings/phy/mvebu_comphy.txt
@@ -0,0 +1,68 @@
+Marvell COMPHY SerDes lane bindings
+=====================================
+
+The COMPHY node includes a description of the COMPHY SerDes lane configuration.
+The COMPHY driver initializes the MUX of the SerDes lanes, and powers up the
SerDes
+by dependencies on the FDT blob configurations
+
+Mandatory properties:
+SoC specific:
+ - compatible:
+ The compatible should include "marvell,mvebu-comphy"
+ and the COMPHY per chip compatible:
+ "marvell,comphy-cp110" for CP110 available in Aramda70x0/80x0.
+ The COMPHY per chip used to set which MUX configuration to use,
and COMPHY power-up revision.
+ - reg: Base address and size of the COMPHY and hpipe units.
+ - max-lanes: Maximum number of comphy lanes.
+ - mux-bitcount: Number of bits that are allocated for every MUX in the
COMPHY-selector register.
+Board specific:
+ - PHY: Entry that include the configuration of the PHY.
+ Every PHY should have the below parameters:
+ - phy-type: the mode of the PHY
+ Possible modes located in include/dt-bindings/comphy/comphy_data.h
+ Optional properties:
+ - phy-speed: the speed of the PHY
+ Possible speeds values located in
include/dt-bindings/comphy/comphy_data.h
+ - phy-invert: Polarity invert
(COMPHY_POLARITY_TXD_INVERT/COMPHY_POLARITY_RXD_INVERT)
+ the possible bits under include/dt-bindings/comphy/comphy_data.h
+ - clk-src: Set the clock source of PCIe, if configured to PCIe clock
output
+ This relevant for SerDes lane 5 only (by default, lane 4 is the
clock source)
+ for Armada-7040 boards.
+ - endpoint: Optional boolean specifying this SerDes should be
configured as PCIe endpoint.
+
+Example:
+ cpm_comphy: comphy@441000 {
+ compatible = "marvell,mvebu-comphy", "marvell,comphy-cp110";
+ reg = <0x441000 0x8>, <0x120000 0x8>;
+ mux-bitcount = <4>;
+ max-lanes = <6>;
+
+ /*
+ * CP110 Serdes Configuration:
+ * Lane 0: SGMII1
+ * Lane 1: SATA 0
+ * Lane 2: USB HOST 0
+ * Lane 3: SATA1
+ * Lane 4: SFI (10G)
+ * Lane 5: SGMII2
+ */
+ phy0 {
+ phy-type = <COMPHY_TYPE_SGMII1>;
+ phy-speed = <COMPHY_SPEED_1_25G>;
+ };
+ phy1 {
+ phy-type = <COMPHY_TYPE_SATA0>;
+ };
+ phy2 {
+ phy-type = <COMPHY_TYPE_USB3_HOST0>;
+ };
+ phy3 {
+ phy-type = <COMPHY_TYPE_SATA1>;
+ };
+ phy4 {
+ phy-type = <COMPHY_TYPE_SFI>;
+ };
+ phy5 {
+ phy-type = <COMPHY_TYPE_SGMII2>;
+ };
+ };
--
2.31.0
