Héllo,
Message: 2
Date: Fri, 13 Aug 2021 12:03:57 +0200
From: Luka Kovacic<[email protected]>
To: Pali Roh?r<[email protected]>
Cc:[email protected], Robert Marko<[email protected]>,
Luka Perkov<[email protected]>, Marek Behun
<[email protected]>,[email protected],[email protected],
[email protected],[email protected]
Subject: Re: [PATCH v3 3/3] arm: mvebu: Initial ESPRESSOBin-Ultra
board support
Message-ID:
<cadzsf3bukpgujq_2yp1zakqbf0hoq_4opldi69_d+qor+hb...@mail.gmail.com>
Content-Type: text/plain; charset="UTF-8"
Hello Pali,
On Fri, Aug 13, 2021 at 11:27 AM Pali Roh?r<[email protected]> wrote:
On Friday 13 August 2021 01:39:38 Luka Kovacic wrote:
Add initial support for the ESPRESSOBin-Ultra board from Globalscale
Technologies, Inc.
The board is based on the 64-bit dual-core Marvell Armada 3720 SoC.
Peripherals:
- 5 Gigabit Ethernet ports (WAN has PoE, up to 30W, Topaz 6341 switch)
- RTC clock (PCF8563)
- USB 3.0 port
- USB 2.0 port
- 4x LED
- UART over Micro-USB
- M.2 slot (2280)
- Mini PCI-E slot
Additionally, automatic import of the Marvell hw_info parameters is
enabled via the recently added mac command for A37XX platforms.
The parameters stored in Marvell hw_info are usually the board serial
number and MAC addresses.
Signed-off-by: Luka Kovacic<[email protected]>
Cc: Luka Perkov<[email protected]>
Cc: Robert Marko<[email protected]>
---
arch/arm/dts/Makefile | 1 +
.../arm/dts/armada-3720-espressobin-ultra.dts | 114 ++++++++++
arch/arm/dts/armada-3720-espressobin.dts | 199 +----------------
arch/arm/dts/armada-3720-espressobin.dtsi | 210 ++++++++++++++++++
board/Marvell/mvebu_armada-37xx/MAINTAINERS | 8 +
board/Marvell/mvebu_armada-37xx/board.c | 92 +++++++-
.../mvebu_espressobin-ultra-88f3720_defconfig | 93 ++++++++
7 files changed, 514 insertions(+), 203 deletions(-)
create mode 100644 arch/arm/dts/armada-3720-espressobin-ultra.dts
create mode 100644 arch/arm/dts/armada-3720-espressobin.dtsi
create mode 100644 configs/mvebu_espressobin-ultra-88f3720_defconfig
...
Thanks, all, for this job.
I am available for testing (if needed) on EspressoBin V7, with eMMC, and
EspressoBin Ultra.
I have issue on EspressoBin Ultra, with the v2 patch for
EspressoBin-Ultra, on OpenWrt 21.02-RC, fw_printenv do not works... (CRC
Error)
I have the same issue with the Marvell (GlobalScale) u-Boot, factory and
upgraded version.
Environments variables are correctly managed from the u-Boot itself.
Regards,
Gérald Kerma
PS : I am only registered to the digest, so I hope my mail will not be
disturbing...
