Héllo Luka,
Le 16/08/2021 à 10:50, Luka Kovacic a écrit :
Hello Gerald,
On Sat, Aug 14, 2021 at 9:59 AM Gérald Kerma <[email protected]> wrote:
Héllo,
Message: 2
Date: Fri, 13 Aug 2021 12:03:57 +0200
From: Luka Kovacic<[email protected]>
To: Pali Roh?r<[email protected]>
Cc:[email protected], Robert Marko<[email protected]>,
Luka Perkov<[email protected]>, Marek Behun
<[email protected]>,[email protected],[email protected],
[email protected],[email protected]
Subject: Re: [PATCH v3 3/3] arm: mvebu: Initial ESPRESSOBin-Ultra
board support
Message-ID:
<cadzsf3bukpgujq_2yp1zakqbf0hoq_4opldi69_d+qor+hb...@mail.gmail.com>
Content-Type: text/plain; charset="UTF-8"
Hello Pali,
On Fri, Aug 13, 2021 at 11:27 AM Pali Roh?r<[email protected]> wrote:
On Friday 13 August 2021 01:39:38 Luka Kovacic wrote:
Add initial support for the ESPRESSOBin-Ultra board from Globalscale
Technologies, Inc.
The board is based on the 64-bit dual-core Marvell Armada 3720 SoC.
Peripherals:
- 5 Gigabit Ethernet ports (WAN has PoE, up to 30W, Topaz 6341 switch)
- RTC clock (PCF8563)
- USB 3.0 port
- USB 2.0 port
- 4x LED
- UART over Micro-USB
- M.2 slot (2280)
- Mini PCI-E slot
Additionally, automatic import of the Marvell hw_info parameters is
enabled via the recently added mac command for A37XX platforms.
The parameters stored in Marvell hw_info are usually the board serial
number and MAC addresses.
Signed-off-by: Luka Kovacic<[email protected]>
Cc: Luka Perkov<[email protected]>
Cc: Robert Marko<[email protected]>
---
arch/arm/dts/Makefile | 1 +
.../arm/dts/armada-3720-espressobin-ultra.dts | 114 ++++++++++
arch/arm/dts/armada-3720-espressobin.dts | 199 +----------------
arch/arm/dts/armada-3720-espressobin.dtsi | 210 ++++++++++++++++++
board/Marvell/mvebu_armada-37xx/MAINTAINERS | 8 +
board/Marvell/mvebu_armada-37xx/board.c | 92 +++++++-
.../mvebu_espressobin-ultra-88f3720_defconfig | 93 ++++++++
7 files changed, 514 insertions(+), 203 deletions(-)
create mode 100644 arch/arm/dts/armada-3720-espressobin-ultra.dts
create mode 100644 arch/arm/dts/armada-3720-espressobin.dtsi
create mode 100644 configs/mvebu_espressobin-ultra-88f3720_defconfig
...
Thanks, all, for this job.
I am available for testing (if needed) on EspressoBin V7, with eMMC, and
EspressoBin Ultra.
Thanks for offering your help. Can you test the following patchset
(v4), when it's out,
as some implementation issues still have to be resolved here?
Sure...
I have issue on EspressoBin Ultra, with the v2 patch for
EspressoBin-Ultra, on OpenWrt 21.02-RC, fw_printenv do not works... (CRC
Error)
I have the same issue with the Marvell (GlobalScale) u-Boot, factory and
upgraded version.
Did you specify the U-Boot environment location correctly in the fw_printenv
config?
I think so : but It do not works...
root@ULTRA-5G:~# cat /etc/fw_env.config
#/dev/mtd0 0x3f0000 0x10000 0x10000 1
/dev/mtd2 0x0 0x10000 0x10000 1
root@ULTRA-5G:~# fw_printenv
Warning: Bad CRC, using default environment
bootcmd=bootp; setenv bootargs root=/dev/nfs
nfsroot=${serverip}:${rootpath}
ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; bootm
bootdelay=5
baudrate=115200
Environments variables are correctly managed from the u-Boot itself.
Regards,
Gérald Kerma
PS : I am only registered to the digest, so I hope my mail will not be
disturbing...
Kind regards,
Luka
Best regards,
Gérald
