Add the support of the LED IP for bcm6357. This
LED IP supports blinking, fading and pulsating,
but for the moment, only blinking is supported.
Signed-off-by: Philippe Reynes <philippe.rey...@softathome.com>
---
drivers/led/Kconfig | 7 +
drivers/led/Makefile | 1 +
drivers/led/led_bcm6753.c | 270 ++++++++++++++++++++++++++++++++++++++
3 files changed, 278 insertions(+)
create mode 100644 drivers/led/led_bcm6753.c
diff --git a/drivers/led/Kconfig b/drivers/led/Kconfig
index cc87fbf395..430d0760ba 100644
--- a/drivers/led/Kconfig
+++ b/drivers/led/Kconfig
@@ -28,6 +28,13 @@ config LED_BCM6358
LED HW controller accessed via MMIO registers.
HW has no blinking capabilities and up to 32 LEDs can be controlled.
+config LED_BCM6753
+ bool "LED Support for BCM6753"
+ depends on LED && ARCH_BCM6753
+ help
+ This option enables support for LEDs connected to the BCM6753
+ HW has blinking and fading capabilities and up to 32 LEDs can be
controlled.
+
config LED_BCM6858
bool "LED Support for BCM6858"
depends on LED && (ARCH_BCM68360 || ARCH_BCM6858 || ARCH_BCM63158)
diff --git a/drivers/led/Makefile b/drivers/led/Makefile
index 8e3ae7f146..2aa2c2173a 100644
--- a/drivers/led/Makefile
+++ b/drivers/led/Makefile
@@ -6,6 +6,7 @@
obj-y += led-uclass.o
obj-$(CONFIG_LED_BCM6328) += led_bcm6328.o
obj-$(CONFIG_LED_BCM6358) += led_bcm6358.o
+obj-$(CONFIG_LED_BCM6753) += led_bcm6753.o
obj-$(CONFIG_LED_BCM6858) += led_bcm6858.o
obj-$(CONFIG_$(SPL_)LED_GPIO) += led_gpio.o
obj-$(CONFIG_LED_CORTINA) += led_cortina.o
diff --git a/drivers/led/led_bcm6753.c b/drivers/led/led_bcm6753.c
new file mode 100644
index 0000000000..a32bd8204f
--- /dev/null
+++ b/drivers/led/led_bcm6753.c
@@ -0,0 +1,270 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2022 Philippe Reynes <philippe.rey...@softathome.com>
+ *
+ * based on:
+ * drivers/led/led_bcm6858.c
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <errno.h>
+#include <led.h>
+#include <log.h>
+#include <asm/io.h>
+#include <dm/lists.h>
+#include <linux/bitops.h>
+
+#define LEDS_MAX 32
+#define LEDS_WAIT 100
+
+/* LED Mode register */
+#define LED_MODE_REG 0x0
+#define LED_MODE_OFF 0
+#define LED_MODE_ON 1
+#define LED_MODE_MASK 1
+
+/* LED Controller Global settings register */
+#define CLED_CTRL_REG 0x00
+#define CLED_CTRL_SERIAL_LED_DATA_PPOL BIT(1)
+#define CLED_CTRL_SERIAL_LED_CLK_POL BIT(2)
+#define CLED_CTRL_SERIAL_LED_EN_POL BIT(3)
+#define CLED_CTRL_SERIAL_LED_MSB_FIRST BIT(4)
+#define CLED_CTRL_MASK 0x1E
+/* LED Controller IP LED source select register */
+#define CLED_HW_LED_EN_REG 0x04
+/* Hardware LED Polarity register */
+#define CLED_HW_LED_IP_PPOL_REG 0x0c
+/* Soft LED Set Register */
+#define CLED_SW_LED_IP_SET_REG 0x10
+/* Parallel LED Output Polarity Register */
+#define CLED_PLED_OP_PPOL_REG 0x18
+/* LED Channel activate register */
+#define CLED_LED_CH_ACTIVATE_REG 0x1c
+/* LED 0 Config 0 reg */
+#define CLED_LED_0_CONFIG_0 0x20
+/* Soft LED Clear Register */
+#define CLED_SW_LED_IP_CLEAR_REG 0x444
+/* Soft LED Status Register */
+#define CLED_SW_LED_IP_STATUS_REG 0x448
+
+/* Size of all registers used for the config of one LED */
+#define CLED_CONFIG_SIZE (4 * sizeof(u32))
+
+#define CLED_CONFIG0_MODE 0
+#define CLED_CONFIG0_MODE_MASK (BIT(0) | BIT(1))
+#define CLED_CONFIG0_MODE_STEADY 0
+#define CLED_CONFIG0_MODE_FADING 1
+#define CLED_CONFIG0_MODE_PULSATING 2
+
+#define CLED_CONFIG0_FLASH_CTRL_SHIFT 3
+#define CLED_CONFIG0_FLASH_CTRL_MASK (BIT(3) | BIT(4) | BIT(5))
+
+struct bcm6753_led_priv {
+ void __iomem *regs;
+ u8 pin;
+};
+
+/*
+ * The value for flash rate are:
+ * 0 : no blinking
+ * 1 : rate is 25 Hz => 40 ms (period)
+ * 2 : rate is 12.5 Hz => 80 ms (period)
+ * 3 : rate is 6.25 Hz => 160 ms (period)
+ * 4 : rate is 3.125 Hz => 320 ms (period)
+ * 5 : rate is 1.5625 Hz => 640 ms (period)
+ * 6 : rate is 0.7815 Hz => 1280 ms (period)
+ * 7 : rate is 0.390625 Hz => 2560 ms (period)
+ */
+static const int bcm6753_flash_rate[8] = {
+ 0, 40, 80, 160, 320, 640, 1280, 2560
+};
+
+static u32 bcm6753_flash_rate_value(int period_ms)
+{
+ unsigned long value = 7;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(bcm6753_flash_rate); i++) {
+ if (period_ms <= bcm6753_flash_rate[i]) {
+ value = i;
+ break;
+ }
+ }
+
+ return value;
+}
+
+static int bcm6753_led_set_period(struct udevice *dev, int period_ms)
+{
+ struct bcm6753_led_priv *priv = dev_get_priv(dev);
+ u32 offset, shift, value;
+
+ offset = CLED_LED_0_CONFIG_0 + (CLED_CONFIG_SIZE * priv->pin);
+ value = bcm6753_flash_rate_value(period_ms);
+ shift = CLED_CONFIG0_FLASH_CTRL_SHIFT;
+
+ /* set mode steady */
+ clrbits_32(priv->regs + offset, CLED_CONFIG0_MODE_MASK);
+ setbits_32(priv->regs + offset, CLED_CONFIG0_MODE_STEADY);
+
+ /* set flash rate */
+ clrbits_32(priv->regs + offset, CLED_CONFIG0_FLASH_CTRL_MASK);
+ setbits_32(priv->regs + offset, value << shift);
+
+ /* enable config */
+ setbits_32(priv->regs + CLED_LED_CH_ACTIVATE_REG, 1 << priv->pin);
+
+ return 0;
+}
+
+static enum led_state_t bcm6753_led_get_state(struct udevice *dev)
+{
+ struct bcm6753_led_priv *priv = dev_get_priv(dev);
+ enum led_state_t state = LEDST_OFF;
+ u32 sw_led_ip_status;
+
+ sw_led_ip_status = readl(priv->regs + CLED_SW_LED_IP_STATUS_REG);
+ if (sw_led_ip_status & (1 << priv->pin))
+ state = LEDST_ON;
+
+ return state;
+}
+
+static int bcm6753_led_set_state(struct udevice *dev, enum led_state_t state)
+{
+ struct bcm6753_led_priv *priv = dev_get_priv(dev);
+
+ switch (state) {
+ case LEDST_OFF:
+ setbits_32(priv->regs + CLED_SW_LED_IP_CLEAR_REG, (1 <<
priv->pin));
+ if (IS_ENABLED(CONFIG_LED_BLINK))
+ bcm6753_led_set_period(dev, 0);
+ break;
+ case LEDST_ON:
+ setbits_32(priv->regs + CLED_SW_LED_IP_SET_REG, (1 <<
priv->pin));
+ if (IS_ENABLED(CONFIG_LED_BLINK))
+ bcm6753_led_set_period(dev, 0);
+ break;
+ case LEDST_TOGGLE:
+ if (bcm6753_led_get_state(dev) == LEDST_OFF)
+ return bcm6753_led_set_state(dev, LEDST_ON);
+ else
+ return bcm6753_led_set_state(dev, LEDST_OFF);
+ break;
+#ifdef CONFIG_LED_BLINK
+ case LEDST_BLINK:
+ setbits_32(priv->regs + CLED_SW_LED_IP_SET_REG, (1 <<
priv->pin));
+ break;
+#endif
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static const struct led_ops bcm6753_led_ops = {
+ .get_state = bcm6753_led_get_state,
+ .set_state = bcm6753_led_set_state,
+#ifdef CONFIG_LED_BLINK
+ .set_period = bcm6753_led_set_period,
+#endif
+};
+
+static int bcm6753_led_probe(struct udevice *dev)
+{
+ struct led_uc_plat *uc_plat = dev_get_uclass_plat(dev);
+
+ /* Top-level LED node */
+ if (!uc_plat->label) {
+ void __iomem *regs;
+ u32 set_bits = 0;
+
+ regs = dev_remap_addr(dev);
+ if (!regs)
+ return -EINVAL;
+
+ if (dev_read_bool(dev, "brcm,serial-led-msb-first"))
+ set_bits |= CLED_CTRL_SERIAL_LED_MSB_FIRST;
+ if (dev_read_bool(dev, "brcm,serial-led-en-pol"))
+ set_bits |= CLED_CTRL_SERIAL_LED_EN_POL;
+ if (dev_read_bool(dev, "brcm,serial-led-clk-pol"))
+ set_bits |= CLED_CTRL_SERIAL_LED_CLK_POL;
+ if (dev_read_bool(dev, "brcm,serial-led-data-ppol"))
+ set_bits |= CLED_CTRL_SERIAL_LED_DATA_PPOL;
+
+ clrsetbits_32(regs + CLED_CTRL_REG, CLED_CTRL_MASK, set_bits);
+ } else {
+ struct bcm6753_led_priv *priv = dev_get_priv(dev);
+ void __iomem *regs;
+ unsigned int pin;
+
+ regs = dev_remap_addr(dev_get_parent(dev));
+ if (!regs)
+ return -EINVAL;
+
+ pin = dev_read_u32_default(dev, "reg", LEDS_MAX);
+ if (pin >= LEDS_MAX)
+ return -EINVAL;
+
+ priv->regs = regs;
+ priv->pin = pin;
+
+ /* this led is managed by software */
+ clrbits_32(regs + CLED_HW_LED_EN_REG, 1 << pin);
+
+ /* configure the polarity */
+ if (dev_read_bool(dev, "active-low"))
+ clrbits_32(regs + CLED_PLED_OP_PPOL_REG, 1 << pin);
+ else
+ setbits_32(regs + CLED_PLED_OP_PPOL_REG, 1 << pin);
+ }
+
+ return 0;
+}
+
+static int bcm6753_led_bind(struct udevice *parent)
+{
+ ofnode node;
+
+ dev_for_each_subnode(node, parent) {
+ struct led_uc_plat *uc_plat;
+ struct udevice *dev;
+ const char *label;
+ int ret;
+
+ label = ofnode_read_string(node, "label");
+ if (!label) {
+ debug("%s: node %s has no label\n", __func__,
+ ofnode_get_name(node));
+ return -EINVAL;
+ }
+
+ ret = device_bind_driver_to_node(parent, "bcm6753-led",
+ ofnode_get_name(node),
+ node, &dev);
+ if (ret)
+ return ret;
+
+ uc_plat = dev_get_uclass_plat(dev);
+ uc_plat->label = label;
+ }
+
+ return 0;
+}
+
+static const struct udevice_id bcm6753_led_ids[] = {
+ { .compatible = "brcm,bcm6753-leds" },
+ { /* sentinel */ }
+};
+
+U_BOOT_DRIVER(bcm6753_led) = {
+ .name = "bcm6753-led",
+ .id = UCLASS_LED,
+ .of_match = bcm6753_led_ids,
+ .bind = bcm6753_led_bind,
+ .probe = bcm6753_led_probe,
+ .priv_auto = sizeof(struct bcm6753_led_priv),
+ .ops = &bcm6753_led_ops,
+};
--
2.17.1
