On 11/19/2024 6:02 AM, Aniket Limaye wrote:
This series adds OPP_LOW spec data in k3_avs driver and enables a config option to select the OPP_LOW performance point.
Whoops, this series is supposed to be v4, missed to update the patch version only in the cover letter.
Will wait for other review comments before resending, if that's fine. Regards, Aniket
J7200 SOC supports OPP_LOW and OPP_NOM as two Operating Performance Points as per (7.5 Operating Performance Points) section in the Datasheet [0]. - A72SS/MSMC at 2 GHz/1GHz operation must use OPP_NOM. - A72SS/MSMC at 1 GHz/500 MHz operation can use OPP_NOM or OPP_LOW voltage (though OPP_LOW voltage is recommended to reduce power consumption). The actual OPP voltage for the device is read from the efuse and updated in k3_avs_probe(). The default j7200 devicetree and k3_avs driver set OPP_NOM spec frequency and voltage. In the board init file, if K3_OPP_LOW config is enabled, Check if OPP_LOW AVS voltage read from efuse is valid and update frequency (A72 and MSMC) and voltage (VDD_CPU) as per the OPP_LOW spec. [0]: https://www.ti.com/lit/gpn/dra821u (J7200 Datasheet) Test logs: https://gist.github.com/aniket-l/328ad93ed60c2419ed7be9f85e6b6075 - With series applied on master and CONFIG_K3_OPP_LOW enabled in j7200_evm_r5_defconfig - Logs shown with and without efuse register programmed for OPP_0 (Errors out if OPP_0 not found, programs OPP_LOW spec if found) - Voltage update verified using 'i2c md 0x4c 0xe' in u-boot - Frequency update verified using 'k3conf clock dump' in linux --- v4: * Manorit - Update function name to k3_avs_check_opp and update description - Move Kconfig definition to arch/arm/mach-k3/r5/Kconfig - Update commit messages - Fixup patch styling problems - In previous versions, fdt_fixup_a72ss_clock_frequency() assumed a fixed order of assigned-clock-rates in the DT to update clk freqs. This may not always be a valid assumption. So, add a new function get_clock_index_by_dev_id() to search the indices for A72 CPU and MSMC clk IDs and then use that index to update the clock rates in place. - Link to v3: https://lore.kernel.org/u-boot/[email protected]/ v3: * Manorit - Use more descriptive name for fdt_fixup_a72ss_clock_frequency() and make function static. - Move error prints (with error codes) before else conditions. Helps with code readability to map error print with the function. - Remove k3_avs_set_opp() from board_init_f altogether. Reasoning being that the value being set through k3_avs_set_opp() will anyway be (correctly) overridden by the k3_avs_notify_freq() call later in the boot process, when a72 freq is actually set from clk_k3. - Add msmc clock at the end to preserve current ordering of core and gtc clocks - Add Kconfig dependency on K3_AVS0 and Update commit msg to make it more clear - Link to v2: https://lore.kernel.org/u-boot/[email protected]/ v2: * Neha - Fix indentation - Updates to commit msgs - Re-format patches 3/5 and 4/5 with logical changes in each patch - Link to v1: https://lore.kernel.org/u-boot/[email protected]/ Reid Tonking (5): arm: dts: k3-j7200-r5-common: Add msmc clk to a72 node misc: k3_avs: Add OPP_LOW voltage and frequency to vd_data misc: k3_avs: Check validity of efuse voltage data arm: mach-k3: j721e-init.c: Add support for CONFIG_K3_OPP_LOW configs: j7200_evm_r5_defconfig: Define K3_OPP_LOW .../arm/dts/k3-j7200-r5-common-proc-board.dts | 10 ++--- arch/arm/mach-k3/Kconfig | 7 ++++ arch/arm/mach-k3/j721e/j721e_init.c | 41 ++++++++++++++++++- configs/j7200_evm_r5_defconfig | 1 + drivers/misc/k3_avs.c | 34 +++++++++++++++ include/k3-avs.h | 2 + 6 files changed, 89 insertions(+), 6 deletions(-)
