On Wed, 2026-05-13 at 09:11 -0500, David Lechner wrote: > Change all uses of tristate in the PHY Kconfigs to bool. U-Boot does > not support modules, so tristate does not make sense here. > > Signed-off-by: David Lechner <[email protected]> > --- > drivers/phy/Kconfig | 14 +++++++------- > drivers/phy/cadence/Kconfig | 4 ++-- > drivers/phy/qcom/Kconfig | 16 ++++++++-------- > drivers/phy/renesas/Kconfig | 6 +++--- > drivers/phy/rockchip/Kconfig | 2 +- > drivers/phy/ti/Kconfig | 2 +- > 6 files changed, 22 insertions(+), 22 deletions(-) > > diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig > index 5c8ec2b146f..eafa82fe494 100644 > --- a/drivers/phy/Kconfig > +++ b/drivers/phy/Kconfig > @@ -114,7 +114,7 @@ config BCM_SR_PCIE_PHY > If unsure, say N. > > config PHY_DA8XX_USB > - tristate "TI DA8xx USB PHY Driver" > + bool "TI DA8xx USB PHY Driver" > depends on PHY && ARCH_DAVINCI > help > Enable this to support the USB PHY on DA8xx SoCs. > @@ -138,7 +138,7 @@ config SPL_PIPE3_PHY > and omap5 > > config AM654_PHY > - tristate "TI AM654 SERDES support" > + bool "TI AM654 SERDES support" > depends on PHY && ARCH_K3 > select REGMAP > select SYSCON > @@ -155,7 +155,7 @@ config STI_USB_PHY > STiH407 SoC families. > > config PHY_RCAR_GEN2 > - tristate "Renesas R-Car Gen2 USB PHY" > + bool "Renesas R-Car Gen2 USB PHY" > depends on PHY && RCAR_GEN2 > help > Support for the Renesas R-Car Gen2 USB PHY. This driver > operates the > @@ -163,7 +163,7 @@ config PHY_RCAR_GEN2 > allows configuring the module multiplexing. > > config PHY_RCAR_GEN3 > - tristate "Renesas R-Car Gen3 USB PHY" > + bool "Renesas R-Car Gen3 USB PHY" > depends on PHY && CLK && DM_REGULATOR && (RCAR_GEN3 || > RZG2L) > default y if (RCAR_GEN3 || RZG2L) > help > @@ -171,7 +171,7 @@ config PHY_RCAR_GEN3 > PHY connected to EHCI USB module and controls USB OTG > operation. > > config PHY_STM32_USBPHYC > - tristate "STMicroelectronics STM32 SoC USB HS PHY driver" > + bool "STMicroelectronics STM32 SoC USB HS PHY driver" > depends on PHY && ARCH_STM32MP > help > Enable this to support the High-Speed USB transceiver that > is part of > @@ -283,7 +283,7 @@ config PHY_MTK_TPHY > so you can easily distinguish them by banks layout. > > config PHY_MTK_UFS > - tristate "MediaTek UFS M-PHY driver" > + bool "MediaTek UFS M-PHY driver" > depends on ARCH_MEDIATEK > depends on PHY > help > @@ -337,7 +337,7 @@ config PHY_IMX8M_PCIE > This PHY is found on i.MX8M devices supporting PCIe. > > config PHY_XILINX_ZYNQMP > - tristate "Xilinx ZynqMP PHY driver" > + bool "Xilinx ZynqMP PHY driver" > depends on PHY && ARCH_ZYNQMP > help > Enable this to support ZynqMP High Speed Gigabit > Transceiver > diff --git a/drivers/phy/cadence/Kconfig > b/drivers/phy/cadence/Kconfig > index 8c0ab80fbbc..f5f096889fe 100644 > --- a/drivers/phy/cadence/Kconfig > +++ b/drivers/phy/cadence/Kconfig > @@ -1,11 +1,11 @@ > config PHY_CADENCE_SIERRA > - tristate "Cadence Sierra PHY Driver" > + bool "Cadence Sierra PHY Driver" > depends on DM_RESET > help > Enable this to support the Cadence Sierra PHY driver > > config PHY_CADENCE_TORRENT > - tristate "Cadence Torrent PHY Driver" > + bool "Cadence Torrent PHY Driver" > depends on DM_RESET > help > Enable this to support the Cadence Torrent PHY driver > diff --git a/drivers/phy/qcom/Kconfig b/drivers/phy/qcom/Kconfig > index 49f830abf01..7094903d869 100644 > --- a/drivers/phy/qcom/Kconfig > +++ b/drivers/phy/qcom/Kconfig > @@ -7,7 +7,7 @@ config MSM8916_USB_PHY > This PHY is found on qualcomm dragonboard410c development > board. > > config PHY_QCOM_IPQ4019_USB > - tristate "Qualcomm IPQ4019 USB PHY driver" > + bool "Qualcomm IPQ4019 USB PHY driver" > depends on PHY && ARCH_IPQ40XX > help > Support for the USB PHY-s on Qualcomm IPQ40xx SoC-s. > @@ -21,26 +21,26 @@ config PHY_QCOM_QMP_COMBO > PHY (USB3 + DisplayPort). Currently only USB3 mode is > supported. > > config PHY_QCOM_QMP_PCIE > - tristate "Qualcomm QMP PCIe PHY driver" > + bool "Qualcomm QMP PCIe PHY driver" > depends on PHY && ARCH_SNAPDRAGON > help > Enable this to support the PCIe QMP PHY on various > Qualcomm chipsets. > > config PHY_QCOM_QMP_UFS > - tristate "Qualcomm QMP UFS PHY driver" > + bool "Qualcomm QMP UFS PHY driver" > depends on PHY && ARCH_SNAPDRAGON > help > Enable this to support the UFS QMP PHY on various Qualcomm > chipsets. > > config PHY_QCOM_QUSB2 > - tristate "Qualcomm USB QUSB2 PHY driver" > + bool "Qualcomm USB QUSB2 PHY driver" > depends on PHY && ARCH_SNAPDRAGON > help > Enable this to support the Super-Speed USB transceiver on > various > Qualcomm chipsets. > > config PHY_QCOM_USB_SNPS_FEMTO_V2 > - tristate "Qualcomm SNPS FEMTO USB HS PHY v2" > + bool "Qualcomm SNPS FEMTO USB HS PHY v2" > depends on PHY && ARCH_SNAPDRAGON > help > Enable this to support the Qualcomm Synopsys DesignWare > Core 7nm > @@ -48,7 +48,7 @@ config PHY_QCOM_USB_SNPS_FEMTO_V2 > is usually paired with Synopsys DWC3 USB IPs on MSM SOCs. > > config PHY_QCOM_SNPS_EUSB2 > - tristate "Qualcomm Synopsys eUSB2 High-Speed PHY" > + bool "Qualcomm Synopsys eUSB2 High-Speed PHY" > depends on PHY && ARCH_SNAPDRAGON > help > Enable this to support the Qualcomm Synopsys DesignWare > eUSB2 > @@ -56,7 +56,7 @@ config PHY_QCOM_SNPS_EUSB2 > is usually paired with Synopsys DWC3 USB IPs on MSM SOCs. > > config PHY_QCOM_USB_HS_28NM > - tristate "Qualcomm 28nm High-Speed PHY" > + bool "Qualcomm 28nm High-Speed PHY" > depends on PHY && ARCH_SNAPDRAGON > help > Enable this to support the Qualcomm Synopsys DesignWare > Core 28nm > @@ -65,7 +65,7 @@ config PHY_QCOM_USB_HS_28NM > IPs on MSM SOCs. > > config PHY_QCOM_USB_SS > - tristate "Qualcomm USB Super-Speed PHY driver" > + bool "Qualcomm USB Super-Speed PHY driver" > depends on PHY && ARCH_SNAPDRAGON > help > Enable this to support the Super-Speed USB transceiver on > various > diff --git a/drivers/phy/renesas/Kconfig > b/drivers/phy/renesas/Kconfig > index affbee0500c..3358d454e59 100644 > --- a/drivers/phy/renesas/Kconfig > +++ b/drivers/phy/renesas/Kconfig > @@ -3,19 +3,19 @@ > # Phy drivers for Renesas platforms > > config PHY_R8A779F0_ETHERNET_SERDES > - tristate "Renesas R-Car S4-8 Ethernet SERDES driver" > + bool "Renesas R-Car S4-8 Ethernet SERDES driver" > depends on RCAR_64 && PHY > help > Support for Ethernet SERDES found on Renesas R-Car S4-8 > SoCs. > > config PHY_R8A78000_ETHERNET_PCS > - tristate "Renesas R-Car X5H Ethernet PCS driver" > + bool "Renesas R-Car X5H Ethernet PCS driver" > depends on RCAR_64 && PHY > help > Support for Ethernet PCS found on Renesas R-Car X5H SoCs. > > config PHY_R8A78000_MP_PHY > - tristate "Renesas R-Car X5H Multi-Protocol PHY driver" > + bool "Renesas R-Car X5H Multi-Protocol PHY driver" > depends on RCAR_64 && PHY > help > Support for Multi-Protocol PHY on Renesas R-Car X5H SoCs. > diff --git a/drivers/phy/rockchip/Kconfig > b/drivers/phy/rockchip/Kconfig > index 80128335d52..6f3d7ebe29e 100644 > --- a/drivers/phy/rockchip/Kconfig > +++ b/drivers/phy/rockchip/Kconfig > @@ -49,7 +49,7 @@ config PHY_ROCKCHIP_SNPS_PCIE3 > also be able splited into multiple combinations of lanes. > > config PHY_ROCKCHIP_USBDP > - tristate "Rockchip USBDP COMBO PHY Driver" > + bool "Rockchip USBDP COMBO PHY Driver" > depends on ARCH_ROCKCHIP > select PHY > help > diff --git a/drivers/phy/ti/Kconfig b/drivers/phy/ti/Kconfig > index df750b26d66..fe96eb6806f 100644 > --- a/drivers/phy/ti/Kconfig > +++ b/drivers/phy/ti/Kconfig > @@ -1,5 +1,5 @@ > config PHY_J721E_WIZ > - tristate "TI J721E WIZ (SERDES Wrapper) support" > + bool "TI J721E WIZ (SERDES Wrapper) support" > depends on ARCH_K3 > help > This option enables support for WIZ module present in TI's > J721E > > --- > base-commit: e3e651c480c46b332f16a7555b97c6c6fd640a40 > change-id: 20260513-phy-kconfig-no-tristate-61bc2d324149 > > Best regards, > -- > David Lechner <[email protected]> >
Reviewed-by: Macpaul Lin <[email protected]> Best regards, Macpaul Lin
