On 09/23/2011 05:13 PM, Fabio Estevam wrote: > When building the zmx25 target we get: > > Configuring for zmx25 board... > generic.c:108: warning: 'get_reset_cause' defined but not used > > Fix this warning by defining get_reset_cause only if CONFIG_DISPLAY_CPUINFO > is defined. > > Signed-off-by: Fabio Estevam <[email protected]> > --- > Changes since v2: > - Move the location of get_reset_cause > Changes since v1: > - Only define get_reset_cause when CONFIG_DISPLAY_CPUINFO is defined. > arch/arm/cpu/arm926ejs/mx25/generic.c | 46 ++++++++++++++++---------------- > 1 files changed, 23 insertions(+), 23 deletions(-) > > diff --git a/arch/arm/cpu/arm926ejs/mx25/generic.c > b/arch/arm/cpu/arm926ejs/mx25/generic.c > index 1261640..8e60a26 100644 > --- a/arch/arm/cpu/arm926ejs/mx25/generic.c > +++ b/arch/arm/cpu/arm926ejs/mx25/generic.c > @@ -105,29 +105,6 @@ ulong imx_get_perclk (int clk) > return lldiv (fref, div); > } > > -static char *get_reset_cause(void) > -{ > - /* read RCSR register from CCM module */ > - struct ccm_regs *ccm = > - (struct ccm_regs *)IMX_CCM_BASE; > - > - u32 cause = readl(&ccm->rcsr) & 0x0f; > - > - if (cause == 0) > - return "POR"; > - else if (cause == 1) > - return "RST"; > - else if ((cause & 2) == 2) > - return "WDOG"; > - else if ((cause & 4) == 4) > - return "SW RESET"; > - else if ((cause & 8) == 8) > - return "JTAG"; > - else > - return "unknown reset"; > - > -} > - > u32 get_cpu_rev(void) > { > u32 srev; > @@ -153,6 +130,29 @@ u32 get_cpu_rev(void) > } > > #if defined(CONFIG_DISPLAY_CPUINFO) > +static char *get_reset_cause(void) > +{ > + /* read RCSR register from CCM module */ > + struct ccm_regs *ccm = > + (struct ccm_regs *)IMX_CCM_BASE; > + > + u32 cause = readl(&ccm->rcsr) & 0x0f; > + > + if (cause == 0) > + return "POR"; > + else if (cause == 1) > + return "RST"; > + else if ((cause & 2) == 2) > + return "WDOG"; > + else if ((cause & 4) == 4) > + return "SW RESET"; > + else if ((cause & 8) == 8) > + return "JTAG"; > + else > + return "unknown reset"; > + > +} > + > int print_cpuinfo (void) > { > char buf[32];
Acked-by: Stefano Babic <[email protected]> Best regards, Stefano Babic -- ===================================================================== DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: [email protected] ===================================================================== _______________________________________________ U-Boot mailing list [email protected] http://lists.denx.de/mailman/listinfo/u-boot
