On Tue, Jul 28, 2026 at 1:26 AM Yao Zi <[email protected]> wrote: > > On Mon, Jul 27, 2026 at 02:59:11PM +0800, Eric Chung wrote: > > Add document on how to flash images into eMMC of K1 SoC based boards. > > > > Signed-off-by: Eric Chung <[email protected]> > > > > --- > > v3: > > - Add document on how to flash images into SD card. > > --- > > board/spacemit/k1/MAINTAINERS | 2 +- > > doc/board/spacemit/index.rst | 1 + > > doc/board/spacemit/k1-mmc.rst | 320 > > ++++++++++++++++++++++++++++++++++++++++++ > > 3 files changed, 322 insertions(+), 1 deletion(-) > > ... > > > diff --git a/doc/board/spacemit/k1-mmc.rst b/doc/board/spacemit/k1-mmc.rst > > new file mode 100644 > > index 00000000000..b0fe78c75ce > > --- /dev/null > > +++ b/doc/board/spacemit/k1-mmc.rst > > @@ -0,0 +1,320 @@ > > ... > > > +Chapter 2: SD Card Boot > > +======================= > > + > > + > > +SpacemiT K1 Bianbu SD Card Image Flashing and U-Boot Update Guide > > +================================================================== > > + > > +This guide explains how to prepare a bootable SD card with Bianbu OS for > > +SpacemiT K1 based boards and how to replace the U-Boot binary on the SD > > +card with a custom build. > > + > > +Prerequisites > > +~~~~~~~~~~~~~ > > + > > +- A SpacemiT K1 based development board > > +- A microSD card (at least 8 GB capacity recommended) > > +- A card reader for your host computer > > +- A Linux host system (for ``dd``, ``fdisk``, ``lsblk`` commands) > > +- The Bianbu SD card image from > > + > > <https://spacemit.com/community/resources-download/Images%20Collects/K1/Bianbu> > > +- A custom ``u-boot.itb`` file (device tree blob or U-Boot FIT image) to be > > + written to the U-Boot partition > > + > > +Prepare the SD Card & the image > > +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ > > + > > +**1. Download the image** > > + > > +Download the released package from the official SpacemiT website: > > + > > +<https://archive.spacemit.com/image/k1/version/bianbu/v2.3.5/Bianbu-Minimal-K1-sdcard-V2.3.5-20260601180942.img.zip> > > + > > +**2. Extract the image** > > + > > +.. code-block:: console > > + > > + $ unzip Bianbu-Minimal-K1-sdcard-V2.3.5-20260601180942.img.zip > > + > > +**3. Identify the SD card device** > > + > > +Insert the microSD card into your card reader, then run: > > + > > +.. code-block:: console > > + > > + $ lsblk > > + > > +Compare the output before and after inserting the card to identify > > +the new device. It will typically appear as ``/dev/sdb``, ``/dev/sdc``, > > +or ``/dev/mmcblk0``. > > + > > +**4. Write the image to the SD card** > > + > > +.. code-block:: console > > + > > + $ sudo dd if=./Bianbu-Minimal-K1-sdcard-V2.3.5-20260601180942.img > > of=/dev/sdb bs=1M status=progress > > + > > +The SD card is now ready as a bootable Bianbu system disk. > > This looks out of scope of describing how to create a bootable SD card > with U-Boot. In my opinion, you'd better describe the requirements of > parition layout and image position for SD-card booting, to allow readers > to create their own images/bootable medium from scratch more easily, > instead of sticking to the vendored image. >
Creating a bootable SD card from scratch would be valuable, but I'll address it later due to time constraints.
