Unreal. This old dog just learnt a new trick.
On Wed, Feb 5, 2014 at 5:15 PM, Daniel McGrath <[email protected]>wrote: > A tip my original mentor taught me on the first day was that in ED/AE, the > back tick (`) gets treated as an empty line so you can keep going in insert > mode and not need to worry about it. > > Regards, > Dan > > > -----Original Message----- > From: [email protected] [mailto: > [email protected]] On Behalf Of Martin Scholl > Sent: Wednesday, February 05, 2014 5:07 PM > To: 'U2 Users List' > Subject: Re: [U2] UniVerse Dictionary question > > The dots were just there to keep the numbered list going, The same I use > dots in the Editor to enter blank lines. Later I go to the top and do > R/.//50 to remove the dot. > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Wjhonson > Sent: Tuesday, February 04, 2014 3:04 PM > To: [email protected] > Subject: Re: [U2] UniVerse Dictionary question > > > What are the periods in 3 and 4 for? > Did you try removing those? > > > > -----Original Message----- > From: Woodward, Bob <[email protected]> > To: U2 Users List <[email protected]> > Sent: Tue, Feb 4, 2014 11:49 am > Subject: Re: [U2] UniVerse Dictionary question > > > Just to make sure, you're wanting FIELD 178 and the first value of that > field. Correct? Because you have a length of 1, left justified I want to > make sure you're not looking for the first character of the 178th field. > Maybe if you showed what you're wanting and what you're getting, instead, > then we'd be sure to give you an answer that makes sense. > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Bill Haskett > Sent: Tuesday, February 04, 2014 11:45 AM > To: U2 Users List > Subject: Re: [U2] UniVerse Dictionary queston > > Martin: > > This is the only way to do accomplish the defined task in UniData. > Maybe "@RECORD<178,1>" is the preferred method in UV. > > Bill > Untitled Page > > > ------------------------------------------------------------------------ > ----- Original Message ----- > *From:* [email protected] > *To:* U2 Users List <[email protected]> > *Date:* 2/4/2014 11:33 AM > *Subject:* [U2] UniVerse Dictionary queston > > UniVerse. > > > > I want to create a dictionary item that extract value <178,1> > > > > I thought > > > > 1. I > > 2. EXTRACT(@RECORD,178,1,0) > > 3. . > > 4. . > > 5. 1L > > 6. S > > > > > > Would do but it does not give me the desired result. Any suggestions? > > > _______________________________________________ > U2-Users mailing list > [email protected] > http://listserver.u2ug.org/mailman/listinfo/u2-users > _______________________________________________ > U2-Users mailing list > [email protected] > http://listserver.u2ug.org/mailman/listinfo/u2-users > > > _______________________________________________ > U2-Users mailing list > [email protected] > http://listserver.u2ug.org/mailman/listinfo/u2-users > > _______________________________________________ > U2-Users mailing list > [email protected] > http://listserver.u2ug.org/mailman/listinfo/u2-users > _______________________________________________ > U2-Users mailing list > [email protected] > http://listserver.u2ug.org/mailman/listinfo/u2-users > _______________________________________________ U2-Users mailing list [email protected] http://listserver.u2ug.org/mailman/listinfo/u2-users
