Yeah I bet the change in pattern is what solved it. -Ty
On Thu, Oct 23, 2014 at 2:44 PM, Josh Luthman <[email protected]> wrote: > We could get to the radio without any noticeable problems via Ethernet. > > In the past year or two we replaced the NSM2 and that fixed the problems > in the past. It did not fix it yesterday. I don't believe it was local > noise, however, it was just with the NSM2 Airview. > > Unfortunately I haven't deployed the (STILL IN BETA) 5.6 with the rate OID > to customers. Consequently, I don't have the rates graphed. At a glance > they seemed fine, but that's not a really good answer to your question. > > My only guess is the culprit of exclusion - multipath. We lost a few db > going from reflector to beam and of course the pattern is going to change > quite a bit, too. > > > Josh Luthman > Office: 937-552-2340 > Direct: 937-552-2343 > 1100 Wayne St > Suite 1337 > Troy, OH 45373 > > On Thu, Oct 23, 2014 at 2:31 PM, Ty Featherling <[email protected]> > wrote: > >> It is 2.4GHz, is it interference from their router? Maybe the leaky NSM2 >> heard the noise but the tighter Nanobeam doesn't as much? Were their air >> rates effected? >> >> -Ty >> >> On Thu, Oct 23, 2014 at 12:20 PM, Matt Corcoran <[email protected]> >> wrote: >> >>> Maybe a problem with the cable. The nanobeam is a different >>> circuit. Could be regarding power, or could be regarding ethernet. >>> My canopy SMs would work with some cables that had a bad crimp or damaged >>> cable, but then when upgrading to ubiquiti, it would not work until I >>> found a bad pin, or damage cable or (arg!) a splice. Or could be a >>> lightning damaged POE. >>> >>> It would be good to do a test using ubiquiti’s built in speedtest to >>> determine if the problem is on the wireless side, or the ethernet side >>> back to the computer. Although low voltage could possible allow it to >>> work until you try running a lot of traffic which increases the draw till >>> the voltage drops below usable level causing a malfunction. >>> >>> >>> From: Mathew Howard <[email protected]> >>> Reply-To: Ubiquiti Users Group <[email protected]> >>> Date: Thursday, October 23, 2014 at 12:49 PM >>> To: Ubiquiti Users Group <[email protected]> >>> >>> Subject: Re: [Ubnt_users] Weird problems >>> >>> My first guess would've been that there's something wrong with the >>> NSM2, but that doesn't make any sense if it was doing the same thing with >>> more than one NSM2... >>> >>> Maybe it's because the NSM2 was a way wider beamwidth? I guess it would >>> make sense if it is picking up an interference source off beam, and the >>> NanoBeam isn't picking it up with it's tighter beamwidth... although I >>> would've thought a reflector should be fairly effective to fix that, but >>> who knows. >>> >>> >>> ------------------------------ >>> *From:* [email protected] [[email protected]] on >>> behalf of Josh Luthman [[email protected]] >>> *Sent:* Thursday, October 23, 2014 11:37 AM >>> *To:* Ubiquiti Users Group >>> *Subject:* Re: [Ubnt_users] Weird problems >>> >>> Tried replacing the NSM2 yesterday first. She's probably had 5 in 2 >>> years. >>> >>> Local noise hotter than -59 and not causing problems with the beam? >>> >>> Josh Luthman >>> Office: 937-552-2340 >>> Direct: 937-552-2343 >>> 1100 Wayne St >>> Suite 1337 >>> Troy, OH 45373 >>> On Oct 23, 2014 12:36 PM, "Sam Tetherow" <[email protected]> wrote: >>> >>>> Bad CPE or local noise? >>>> >>>> On 10/23/2014 11:31 AM, Josh Luthman wrote: >>>> >>>> So I've got 31 subs on this 2 GHz AP. 30 of them never have issues. 1 >>>> customer has had problems probably 4-6 occurrences in the last two years. >>>> Previously we've had NSM2 and NSM2 + reflector. The signal is great (-59) >>>> however from the RF end I can't even get to the HTTP interface. SSH >>>> sometimes gets a prompt, but I can't even log in. Mind you every other >>>> user has no problems! >>>> >>>> Yesterday we swapped to a Nanobeam and everything works fantastic. >>>> WHY? >>>> >>>> http://i.imgur.com/beBkZ97.png >>>> >>>> Josh Luthman >>>> Office: 937-552-2340 >>>> Direct: 937-552-2343 >>>> 1100 Wayne St >>>> Suite 1337 >>>> Troy, OH 45373 >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing >>>> [email protected]http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>> _______________________________________________ >>> Ubnt_users mailing list >>> [email protected] >>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>> >>> >> >> _______________________________________________ >> Ubnt_users mailing list >> [email protected] >> http://lists.wispa.org/mailman/listinfo/ubnt_users >> >> > > _______________________________________________ > Ubnt_users mailing list > [email protected] > http://lists.wispa.org/mailman/listinfo/ubnt_users > >
_______________________________________________ Ubnt_users mailing list [email protected] http://lists.wispa.org/mailman/listinfo/ubnt_users
