Good evening.
We had this happen when we reloaded a router at an active site after a dhcp issue, and we are in the process of bring up a new site and figured we would try it on a fresh router without any risk of bringing a customer down. We loaded the router with 1.7, as this is the production firmware we are running across all routers in our network presently. Completed config, ospf is working everything is behaving as expected. Backup config and then loaded 1.8.5. As soon as router reboots, it is no longer accessible. From the next router in line, i can ping public interface of new router, but cannot do anything else(This most likely due to firewall rules we have in place). Router is online, but ospf is no longer working. It is no longer listed as a registered neighbor and in fact appears that ospf is turned off as a whole. Last time we did this on the production router, it was available locally but ospf did not work. It appears this is the case here as well. Any help would be greatly appreciated as we need to upgrade our entire infrastructure to take advantage of the MPLS configurations for an upcoming project for a customer. Thank you in advance! So to further this, i am working at the site and trying to resolve this, so far to no end. Here is th ospf database: OSPF Router with ID (199.83.117.14) (Process ID 0 VRF default) Router Link States (Area 0.0.0.0) Link ID ADV Router Age Seq# CkSum Link count 199.83.117.14 199.83.117.14 378 0x80000005 0xbcad 3 show ip ospf interface eth1 eth1 is up, line protocol is up Internet Address 199.83.117.14/30, Area 0.0.0.0, MTU 1500 Process ID 0, VRF (default), Router ID 199.83.117.14, Network Type BROADCAST, Cost: 10 Transmit Delay is 1 sec, State DR, Priority 1, TE Metric 10 Designated Router (ID) 199.83.117.14, Interface Address 199.83.117.14 No backup designated router on this network Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:05 Neighbor Count is 0, Adjacent neighbor count is 0 Crypt Sequence Number is 185 Hello received 0 sent 97, DD received 0 sent 0 LS-Req received 0 sent 0, LS-Upd received 0 sent 0 LS-Ack received 0 sent 0, Discarded 0 Message-digest authentication, using default key-id 0 set protocols ospf area 0.0.0.0 area-type normal set protocols ospf area 0.0.0.0 authentication md5 set protocols ospf area 0.0.0.0 network 199.83.117.12/30 set protocols ospf area 0.0.0.0 network 172.16.106.0/24 set protocols ospf area 0.0.0.0 network 199.83.117.128/25 set protocols ospf parameters abr-type cisco set protocols ospf parameters router-id 199.83.117.14 packet capture of ospf on the eth1 interface: 16:28:25.895751 IP (tos 0xc0, ttl 1, id 46663, offset 0, flags [none], proto OSPF (89), length 64) 199.83.117.13 > 224.0.0.5: OSPFv2, Hello, length 44 Router-ID 74.116.132.65, Backbone Area, Authentication Type: none (0) Options [External] Hello Timer 10s, Dead Timer 40s, Mask 255.255.255.252, Priority 1 Designated Router 199.83.117.13 16:28:31.569879 IP (tos 0xc0, ttl 1, id 9546, offset 0, flags [DF], proto OSPF (89), length 80) 199.83.117.14 > 224.0.0.5: OSPFv2, Hello, length 44 Router-ID 199.83.117.129, Backbone Area, Authentication Type: MD5 (2) Key-ID: 0, Auth-Length: 16, Crypto Sequence Number: 0x0000053a Options [External] Hello Timer 10s, Dead Timer 40s, Mask 255.255.255.252, Priority 1 Designated Router 199.83.117.14 No idea why this isnt working. Also checked ps aux and it shows: root 2126 0.0 0.1 6932 2872 ? Ss 16:02 0:00 /usr/sbin/ospfd -d -P 0 This thing is just dead in the water... Any help or guidance would be greatly appreciated. Thank you.
_______________________________________________ Ubnt_users mailing list [email protected] http://lists.wispa.org/mailman/listinfo/ubnt_users
