Said differently, even though .13 is configured for it, the hello packet
doesn't appear to be reflecting that config.
Get Outlook for Android
On Sat, Jul 30, 2016 at 10:27 PM -0600, "Nathan Babcock"
<nath...@sswireless.net> wrote:
13 adn 14 are set to MD5. Just reverified this.
On 7/30/2016 10:20 PM, Jesse Dupont
wrote:
It looks like there is an Authentication Type
mismatch. .13 is set to none whereas .14 is set to MD5.
On Sat, Jul 30, 2016 at 9:49 PM, <nath...@sswireless.net>
wrote:
Good evening.
We had this happen when we reloaded a router at an active
site after a dhcp issue, and we are in the process of
bring up a new site and figured we would try it on a fresh
router without any risk of bringing a customer down.
We loaded the router with 1.7, as this is the production
firmware we are running across all routers in our network
presently. Completed config, ospf is working everything
is behaving as expected. Backup config and then loaded
1.8.5. As soon as router reboots, it is no longer
accessible. From the next router in line, i can ping
public interface of new router, but cannot do anything
else(This most likely due to firewall rules we have in
place). Router is online, but ospf is no longer working.
It is no longer listed as a registered neighbor and in
fact appears that ospf is turned off as a whole.
Last time we did this on the production router, it was
available locally but ospf did not work. It appears this
is the case here as well. Any help would be greatly
appreciated as we need to upgrade our entire
infrastructure to take advantage of the MPLS
configurations for an upcoming project for a customer.
Thank you in advance!
So to further this, i am working at the site and trying
to resolve this, so far to no end.
Here is th ospf database:
OSPF Router with ID (199.83.117.14) (Process ID 0 VRF
default)
Router Link States (Area 0.0.0.0)
Link ID ADV Router Age Seq# CkSum Link count
199.83.117.14 199.83.117.14 378 0x80000005 0xbcad 3
show ip ospf interface eth1
eth1 is up, line protocol is up
Internet Address 199.83.117.14/30,
Area 0.0.0.0, MTU 1500
Process ID 0, VRF (default), Router ID 199.83.117.14,
Network Type BROADCAST, Cost: 10
Transmit Delay is 1 sec, State DR, Priority 1, TE Metric
10
Designated Router (ID) 199.83.117.14, Interface Address
199.83.117.14
No backup designated router on this network
Timer intervals configured, Hello 10, Dead 40, Wait 40,
Retransmit 5
Hello due in 00:00:05
Neighbor Count is 0, Adjacent neighbor count is 0
Crypt Sequence Number is 185
Hello received 0 sent 97, DD received 0 sent 0
LS-Req received 0 sent 0, LS-Upd received 0 sent 0
LS-Ack received 0 sent 0, Discarded 0
Message-digest authentication, using default key-id 0
set protocols ospf area 0.0.0.0 area-type normal
set protocols ospf area 0.0.0.0 authentication md5
set protocols ospf area 0.0.0.0 network 199.83.117.12/30
set protocols ospf area 0.0.0.0 network 172.16.106.0/24
set protocols ospf area 0.0.0.0 network 199.83.117.128/25
set protocols ospf parameters abr-type cisco
set protocols ospf parameters router-id 199.83.117.14
packet capture of ospf on the eth1 interface:
16:28:25.895751 IP (tos 0xc0, ttl 1, id 46663, offset 0,
flags [none], proto OSPF (89), length 64)
199.83.117.13 > 224.0.0.5:
OSPFv2, Hello, length 44
Router-ID 74.116.132.65, Backbone Area, Authentication
Type: none (0)
Options [External]
Hello Timer 10s, Dead Timer 40s, Mask 255.255.255.252,
Priority 1
Designated Router 199.83.117.13
16:28:31.569879 IP (tos 0xc0, ttl 1, id 9546, offset 0,
flags [DF], proto OSPF (89), length 80)
199.83.117.14 > 224.0.0.5:
OSPFv2, Hello, length 44
Router-ID 199.83.117.129, Backbone Area, Authentication
Type: MD5 (2)
Key-ID: 0, Auth-Length: 16, Crypto Sequence Number:
0x0000053a
Options [External]
Hello Timer 10s, Dead Timer 40s, Mask 255.255.255.252,
Priority 1
Designated Router 199.83.117.14
No idea why this isnt working.
Also checked ps aux and it shows:
root 2126 0.0 0.1 6932 2872 ? Ss 16:02 0:00
/usr/sbin/ospfd -d -P 0
This thing is just dead in the water...
Any help or guidance would be greatly appreciated. Thank
you.
_______________________________________________
Ubnt_users mailing list
Ubnt_users@wispa.org
http://lists.wispa.org/mailman/listinfo/ubnt_users
--
Jesse
DuPont
Owner
/ Network Architect
email: jesse.dup...@celeritycorp.net
cell: 605-340-0651
fax: 305-946-0651
Celerity
Networks LLC
PO
Box 547
Spearfish,
SD 57783
Like
us! facebook.com/celeritynetworksllc
_______________________________________________
Ubnt_users mailing list
Ubnt_users@wispa.org
http://lists.wispa.org/mailman/listinfo/ubnt_users
_______________________________________________
Ubnt_users mailing list
Ubnt_users@wispa.org
http://lists.wispa.org/mailman/listinfo/ubnt_users
