Jesse,
Thank you for the second look. That solved my issue. I overlooked that
probably 20 times as i was trying to understand what was wrong. I have now
looked at 4 more routers and all their links and as is the case with this one,
1.7 apparently ignores the md5 authentication. I will be disabling this
throughout my network prior to upgrading. This created a fair amount of
frustration for me.
----- Original Message -----
From: [email protected] [mailto:[email protected]]
To: Ubiquiti Users Group [email protected]
Sent: Sun, 31 Jul 2016 04:37:33 +0000 (UTC)
Subject: Re: [Ubnt_users] upgrading edgemax from 1.7 to 1.8.5 OSPF stops
working
Said differently, even though .13 is configured for it, the hello packet
doesn't appear to be reflecting that config.
Get Outlook for Android
On Sat, Jul 30, 2016 at 10:27 PM -0600, "Nathan Babcock"
<[email protected]> wrote:
13 adn 14 are set to MD5. Just reverified this.
On 7/30/2016 10:20 PM, Jesse Dupont wrote:
It looks like there is an Authentication Type mismatch. .13 is set to none
whereas .14 is set to MD5.
On Sat, Jul 30, 2016 at 9:49 PM, <[email protected]> wrote:
Good evening.
We had this happen when we reloaded a router at an active site after a dhcp
issue, and we are in the process of bring up a new site and figured we would
try it on a fresh router without any risk of bringing a customer down.
We loaded the router with 1.7, as this is the production firmware we are
running across all routers in our network presently. Completed config, ospf is
working everything is behaving as expected. Backup config and then loaded
1.8.5. As soon as router reboots, it is no longer accessible. From the next
router in line, i can ping public interface of new router, but cannot do
anything else(This most likely due to firewall rules we have in place). Router
is online, but ospf is no longer working. It is no longer listed as a
registered neighbor and in fact appears that ospf is turned off as a whole.
Last time we did this on the production router, it was available locally but
ospf did not work. It appears this is the case here as well. Any help would
be greatly appreciated as we need to upgrade our entire infrastructure to take
advantage of the MPLS configurations for an upcoming project for a customer.
Thank you in advance!
So to further this, i am working at the site and trying to resolve this, so far
to no end.
Here is th ospf database:
OSPF Router with ID (199.83.117.14) (Process ID 0 VRF default)
Router Link States (Area 0.0.0.0)
Link ID ADV Router Age Seq# CkSum Link count
199.83.117.14 199.83.117.14 378 0x80000005 0xbcad 3
show ip ospf interface eth1
eth1 is up, line protocol is up
Internet Address 199.83.117.14/30, Area 0.0.0.0, MTU 1500
Process ID 0, VRF (default), Router ID 199.83.117.14, Network Type BROADCAST,
Cost: 10
Transmit Delay is 1 sec, State DR, Priority 1, TE Metric 10
Designated Router (ID) 199.83.117.14, Interface Address 199.83.117.14
No backup designated router on this network
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
Hello due in 00:00:05
Neighbor Count is 0, Adjacent neighbor count is 0
Crypt Sequence Number is 185
Hello received 0 sent 97, DD received 0 sent 0
LS-Req received 0 sent 0, LS-Upd received 0 sent 0
LS-Ack received 0 sent 0, Discarded 0
Message-digest authentication, using default key-id 0
set protocols ospf area 0.0.0.0 area-type normal
set protocols ospf area 0.0.0.0 authentication md5
set protocols ospf area 0.0.0.0 network 199.83.117.12/30
set protocols ospf area 0.0.0.0 network 172.16.106.0/24
set protocols ospf area 0.0.0.0 network 199.83.117.128/25
set protocols ospf parameters abr-type cisco
set protocols ospf parameters router-id 199.83.117.14
packet capture of ospf on the eth1 interface:
16:28:25.895751 IP (tos 0xc0, ttl 1, id 46663, offset 0, flags [none], proto
OSPF (89), length 64)
199.83.117.13 > 224.0.0.5: OSPFv2, Hello, length 44
Router-ID 74.116.132.65, Backbone Area, Authentication Type: none (0)
Options [External]
Hello Timer 10s, Dead Timer 40s, Mask 255.255.255.252, Priority 1
Designated Router 199.83.117.13
16:28:31.569879 IP (tos 0xc0, ttl 1, id 9546, offset 0, flags [DF], proto OSPF
(89), length 80)
199.83.117.14 > 224.0.0.5: OSPFv2, Hello, length 44
Router-ID 199.83.117.129, Backbone Area, Authentication Type: MD5 (2)
Key-ID: 0, Auth-Length: 16, Crypto Sequence Number: 0x0000053a
Options [External]
Hello Timer 10s, Dead Timer 40s, Mask 255.255.255.252, Priority 1
Designated Router 199.83.117.14
No idea why this isnt working.
Also checked ps aux and it shows:
root 2126 0.0 0.1 6932 2872 ? Ss 16:02 0:00 /usr/sbin/ospfd -d -P 0
This thing is just dead in the water...
Any help or guidance would be greatly appreciated. Thank you.
_______________________________________________
Ubnt_users mailing list
[email protected]
http://lists.wispa.org/mailman/listinfo/ubnt_users
--
Jesse DuPont
Owner / Network Architect
email: [email protected]
cell: 605-340-0651
fax: 305-946-0651
Celerity Networks LLC
PO Box 547
Spearfish, SD 57783
Like us! facebook.com/celeritynetworksllc
_______________________________________________Ubnt_users mailing
[email protected]http://lists.wispa.org/mailman/listinfo/ubnt_users
_______________________________________________
Ubnt_users mailing list
[email protected]
http://lists.wispa.org/mailman/listinfo/ubnt_users
