Pessoal,
Desculpe-me, ainda sou leigo pois usei linux a muito tempo atras e estou
tentando me atualizar novamente agora.
Tenho uma placa de WiFi Edimax (chipset Ralink) instalada no micro o qual
instalei o Ubuntu 6.0 porém não estou conseguindo me comunicar com a rede,
aparentemente não está reconhecendo a placa.
Simplesmente na configuração de Wireless não mostra nenhuma rede WiFi
proxima e mesmo configurando manualmente não consigo "pingar" nenhum ip da
rede.
Anexei o arquivo README ao e-mail para que possam me auxiliar.
O CD-ROM da placa possui arquivos .c e .h para configurar no linux e
justamente a parte que não estou conseguindo seguir é:
For 2.6 series kernel:
a. run 'cd STA/Module'
'cp ../2.6.x/Makefile .'
b. $make -C /path/to/source SUBDIRS=$PWD modules
Where /path/to/source is the path to the source directory for the
(configured and built) target kernel.
c. run '/sbin/insmod rt2500.ko' (as root)
'/sbin/ifconfig ra0 inet YOUR_IP up'
For big endian platform:
a. replace Makefile with Makefile.BigEndian
Obrigado antecipadamente pela ajuda.
Grande abraço,
Guilherme
_________________________________________________________________
MSN Hotmail, o maior webmail do Brasil. http://www.hotmail.com
* README
*
* Ralink Tech Inc.
*
* http://www.ralinktech.com
*
=======================================================================
ModelName:
===========
RT2500
=======================================================================
Supporting Kernel:
===================
linux kernel 2.4 and 2.6 series.
Tested in Redhat 7.3 or later, Fedora Core 1, Suse 8.0,8.1,9.0, Mandrake
9.0->10.0, Slackware 9.0,9.1
=======================================================================
Description:
=============
This is a linux device driver for Ralink RT2500 b/g WLAN Card.
=======================================================================
Contents:
=============
./2.4.x : Makefile for kernel 2.4 series
./2.6.x : Makefile for kernel 2.6 series
*.c : c files
*.h : header files
Makefile.BigEndian : Makefile for big endian platform
=======================================================================
Features:
==========
This driver implements basic IEEE802.11. Infrastructure and adhoc mode
with open or shared or WPA
authentication method. WEP-40 and WEP-104 TKIP and AES encryption,
=======================================================================
Build Instructions:
====================
For 2.4 series kernel:
a. $tar -xvzf RT2500-Linux-STA-x.x.x.x.tar.gz
go to "./RT2500-Linux-STA-x.x.x.x/Module" directory.
b. Use 'chmod' command to change access right of following script files :
'load', 'unload', 'Configure'
c. run 'cp ../2.6.x/Makefile .'
d. $make config # config build linux os version
e. $make all # compile driver source code
f. $load # load/insmod module(rt2500.o)
Note: Script functionality:
load load module to kernel
unload unload module from kernel
Configure retrieve linux version
For 2.6 series kernel:
a. run 'cd STA/Module'
'cp ../2.6.x/Makefile .'
b. $make -C /path/to/source SUBDIRS=$PWD modules
Where /path/to/source is the path to the source directory for the
(configured and built) target kernel.
c. run '/sbin/insmod rt2500.ko' (as root)
'/sbin/ifconfig ra0 inet YOUR_IP up'
For big endian platform:
a. replace Makefile with Makefile.BigEndian
=======================================================================
To BUILD UTILITY
====================
a. go to the "./Utility" directory
b. run 'qmake -o Makefile raconfig2500.pro'
If qmake command is not found in your system, you can download the QT
tool
'qt-x11-free-3.2.1' or later at
http://www.trolltech.com/
(qmake comes with RedHat 7.3 or later QT Package)
c. run 'make" to compile the utility source code.
d. After all, an execution file would be generated "RaConfig2500"
run "RaConfig2500" to config the driver as you want
=======================================================================
CONFIGURATION:
====================
RT2500 driver can be configured via following interfaces,
i.e. (i)"iwconfig" command, (ii)"iwpriv" command, (iii) configuration file,
(iv) RaConfig2500
i) iwconfig comes with kernel.
ii) iwpriv usage, please refer to file "iwpriv_usage.txt" for details.
iii)copy configuration file "RT2500STA.dat" to
/etc/Wireless/RT2500STA/RT2500STA.dat.
Please refer to 3.1) for details.
iv) RT2500 provides API : RaConfig2500, please go to directory ./Utility and
refer to how-to-compile.txt
Configuration File : RT2500STA.dat
# Copy this file to /etc/Wireless/RT2500STA/RT2500STA.dat
# This file is a binary file and will be read on loading rt2500.o module.
#
# Use "vi -b RT2500STA.dat" to modify settings according to your need.
#
# 1.) set NetworkType to "Adhoc" for using Adhoc-mode, otherwise using as
Infrastructure-mode
# 2.) set Channel to "0" for auto-select on Infrastructure mode
# 3.) set SSID for connecting to your Accss-point.
# 4.) AuthMode can be "OPEN", "SHARED", "WPAPSK", "WPANONE"
# 5.) EncrypType can be "NONE", "WEP", "TKIP", "AES"
# for more information refer to the Readme file.
#
[Default]
CountryRegion=0
WirelessMode=0
SSID=AP350
NetworkType=Infra
Channel=0
AuthMode=OPEN
EncrypType=NONE
DefaultKeyID=1
Key1Type=0
Key1Str=0123456789
Key2Type=0
Key2Str=
Key3Type=0
Key3Str=
Key4Type=0
Key4Str=
WPAPSK=abcdefghijklmnopqrstuvwxyz
TXBurst=0
TurboRate=0
BGProtection=0
ShortSlot=0
TxRate=0
RTSThreshold=2312
FragThreshold=2312
PSMode=CAM
-----------------------------------------------
syntax is 'Param'='Value' and describes below.
1. CountryRegion=value
value
0: for use channel 1-11
1: for use channel 1-11
2: for use channel 1-13
3: for use channel 10-11
4: for use channel 10-13
5: for use channel 14
6: for use channel 1-14
7: for use channel 3-9
2. WirelessMode=value
value
0: 802.11 B/G mixed
1: 802.11 B only
3. SSID=value
value
1~32 ascii characters.
4. NetworkType=Infra
value
Infra : infrastructure mode
Adhoc : adhoc mode
5. Channel=value
value
1~14 depends on CountryRegion
6. AuthMode=value
value
OPEN For Open System
SHARED For Shared key system
WPAPSK
7. EncrypType=value
value
NONE :For AuthMode=OPEN
WEP :For AuthMode=OPEN or AuthMode=SHARED
TKIP :For AuthMode=WPAPSK
AES :For AuthMode=WPAPSK
8. DefaultKeyID=value
value
1 ~ 4
9. Key1Type=value
value
0: Hexadecimal
1: Ascii
10. Key1Str=value
value
10 or 26 hexadecimal characters eg: 012345678
5 or 13 ascii characters eg: passd
11. Key2Type=value
value
0: Hexadecimal
1: Ascii
12. Key2Str=value
value
10 or 26 hexadecimal characters eg: 012345678
5 or 13 ascii characters eg: passd
13. Key3Type=value
value
0: Hexadecimal
1: Ascii
14. Key3Str=value
value
10 or 26 hexadecimal characters eg: 012345678
5 or 13 ascii characters eg: passd
15. Key4Type=value
value
0: Hexadecimal
1: Ascii
16. Key4Str=value
value
10 or 26 hexadecimal characters eg: 012345678
5 or 13 ascii characters eg: passd
17. WPAPSK=value
value
8 ~ 63 characters
or
64 hexadecimal characters
18. TxBurst=value
value
0: Disable
1: Enable
19. TurboRate=value
value
0: Disable
1: Enable
20. BGProtection=value
value
0: Auto
1: Always On
2: Always Off
21. ShortSlot=value
value
0: Disable
1: Enable
22. TxRate=value
value
0: Auto
1: 1 Mbps
2: 2 Mbps
3: 5.5 Mbps
4: 11 Mbps
5: 6 Mbps //WirelessMode must be 0
6: 9 Mbps //WirelessMode must be 0
7: 12 Mbps //WirelessMode must be 0
8: 18 Mbps //WirelessMode must be 0
9: 24 Mbps //WirelessMode must be 0
10: 36 Mbps //WirelessMode must be 0
11: 48 Mbps //WirelessMode must be 0
12: 54 Mbps //WirelessMode must be 0
23. RTSThreshold=value
value
1 ~ 2312
24. FragThreshold=value
value
256 ~ 2312
25. PSMode=value
value
MAX_PSP Power Saving Mode
CAM CAM (Constantly Awake Mode)
26. AdhocOfdm=value
value
0: Adhere WIFI spec, the Tx MAX rate will be 11Mbps in Adhoc mode
1: Violate WIFI spec, the Tx MAX rate will be 54Mbps in Adhoc mode
27. StaWithEtherBridge=value
value
0: Disable sta with ethernet to wireless bridge
1: Enable sta with ethernet to wireless bridge
MORE INFORMATION
=================================================================================
If you want for rt2500 driver to auto-load at boot time:
A) choose ra0 for first RT2500 WLAN card, ra1 for second RT2500 WLAN card,
etc.
B) create(edit) 'ifcfg-ra0' file in /etc/sysconfig/network-scripts/,
edit( or add the line) in /etc/modules.conf:
alias ra0 rt2500
C) edit(create) the file /etc/sysconfig/network-scripts/ifcfg-ra0
DEVICE='ra0'
ONBOOT='yes'
NOTE:
if you use dhcp, add this line too .
BOOTPROTO='dhcp'
*D) To ease the Default Gateway setting,
add the line
GATEWAY=x.x.x.x
in /etc/sysconfig/network
==================================================================================
= To install a device driver for Ralink RT2500 b/g WLAN card in AMD64 SUSE
Linux =
==================================================================================
A.
1.Edit(or add the line) in /etc/modules.conf
alias ra0 rt2500
2.Create and edit 'ifcfg-ra0' file in /etc/sysconfig/network/
DEVICE='ra0'
ONBOOT='yes'
BOOTPROTO='dhcp'
B. $tar -xvzf RT2500--Linux-STA-x.x.x.x.tar.gz
Go to "./RT2500-Linux-STA-x.x.x.x/Module" directory
1.Copy ./Module/2.6.x/Makefile to "./Module" directory
2.$make -C /usr/src/linux-2.6.8-gentoo-r3 SUBDIRS=$PWD modules
where linux-2.6.8-gentoo-r3 is your 2.6 kernel name
3.$insmod rt2500.ko
4.$ifconfig ra0 up
5.$iwconfig ra0 essid any
6.$dhcpcd ra0&
7.$dhcpcd ra0
Now it should be functional - type
$iwconfig
to confirm setting
C.Activate it on startup with a script.
1.Input your script file 'wlancfg' in /etc/init.d/
2.Start applicaiton YaST in System, choose system -> runlevel editor
3.In expert mode, enable 'wlancfg' in runlevel 5.
--
ubuntu-br mailing list
[email protected]
www.ubuntubrasil.org
https://lists.ubuntu.com/mailman/listinfo/ubuntu-br
