Public bug reported:
1, grub boot log
TianoCore 2.0.0 UEFI 2.4.0 Sep 1 2015 12:48:07
CPU: APM ARM 64-bit Strega Rev A2 2400MHz PCP 2400MHz
32 KB ICACHE, 32 KB DCACHE
SOC 2000MHz IOBAXI 400MHz AXI 250MHz AHB 200MHz GFC 66MHz
Board: X-Gene Merlin Board
Slimpro FW:
Ver: 3.4 (build 2015/07/22)
PMD: 980 mV
SOC: 950 mV
The default boot selection will start in 3 seconds
[1] ubuntu
[2] PXE on MAC :3C
[3] Shell
[4] Boot Manager
[5] Reboot
[6] Shutdown
Start: 1
error: no suitable video mode found.
error: failure writing sector 0x19df788 to `hd0'.
2, disk information
2.1 parted
ubuntu@ubuntu:~$ sudo parted /dev/sda -- print
Model: ATA Corsair Neutron (scsi)
Disk /dev/sda: 120GB
Sector size (logical/physical): 512B/512B
Partition Table: gpt
Disk Flags:
Number Start End Size File system Name Flags
1 1049kB 538MB 537MB fat16 EFI System Partition boot, esp
2 538MB 87.1GB 86.5GB ext4
3 87.1GB 120GB 32.9GB linux-swap(v1)
2.2 hdparm -I
ubuntu@ubuntu:~$ sudo hdparm -I /dev/sda
/dev/sda:
ATA device, with non-removable media
Model Number: Corsair Neutron GTX SSD
Serial Number: 13447908000097140140
Firmware Revision: M311
Transport: Serial, ATA8-AST, SATA 1.0a, SATA II Extensions,
SATA Rev 2.5
Standards:
Supported: 8 7 6 5
Likely used: 8
Configuration:
Logical max current
cylinders 16383 0
heads 16 0
sectors/track 63 0
--
LBA user addressable sectors: 234441648
LBA48 user addressable sectors: 234441648
Logical/Physical Sector size: 512 bytes
device size with M = 1024*1024: 114473 MBytes
device size with M = 1000*1000: 120034 MBytes (120 GB)
cache/buffer size = unknown
Nominal Media Rotation Rate: Solid State Device
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 1
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* 48-bit Address feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* WRITE_{DMA|MULTIPLE}_FUA_EXT
WRITE_DMA_QUEUED_FUA_EXT
* WRITE_UNCORRECTABLE_EXT command
* {READ,WRITE}_DMA_EXT_GPL commands
* Gen1 signaling speed (1.5Gb/s)
* Gen2 signaling speed (3.0Gb/s)
* Gen3 signaling speed (6.0Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
* Device automatic Partial to Slumber transitions
* READ_LOG_DMA_EXT equivalent to READ_LOG_EXT
Non-Zero buffer offsets in DMA Setup FIS
DMA Setup Auto-Activate optimization
Device-initiated interface power management
In-order data delivery
* Software settings preservation
* Data Set Management TRIM supported (limit 1 block)
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
Checksum: correct
** Affects: grub2 (Ubuntu)
Importance: Undecided
Status: New
--
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.
https://bugs.launchpad.net/bugs/1512193
Title:
arm64: report 'error: failure writing sector 0x19df788 to `hd0'' after
a fresh install
To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/grub2/+bug/1512193/+subscriptions
--
ubuntu-bugs mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
