Is there any useful information I can give to help anybody debug this?
Here's part of dmesg from the 2.6.15-26 kernel which boots:

[   30.228987] libata version 1.20 loaded.
[   30.229872] sata_nv 0000:00:0e.0: version 0.8
[   30.230415] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
[   30.230458] GSI 16 sharing vector 0xC9 and IRQ 16
[   30.230499] ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APSI] -> GSI 23 
(level, low) -> IRQ 201
[   30.230757] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[   30.230840] ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xE000 irq 201
[   30.230899] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xE008 irq 201

>>> This is where the 2.6.17-10 kernel stops!  <<<

[   30.598718] ata1: dev 0 cfg 00:0c5a 49:2f00 82:3069 83:7c01 84:4023 85:3069 
86:3c01 87:4023 88:203f 93:0000
[   30.598722] ata1: dev 0 ATA-7, max UDMA/100, 625142448 sectors: LBA48
[   30.603080] sata_get_dev_handle: SATA dev addr=0xe0000, 
handle=0xffff810037fde6c0
[   30.610981] ata1: dev 0 configured for UDMA/100
[   30.615279] sata_get_dev_handle: SATA dev addr=0xe0000, 
handle=0xffff810037fde6c0
[   30.623007] scsi0 : sata_nv
[   30.826325] ata2: no device found (phy stat 00000000)
[   30.826362] scsi1 : sata_nv
[   30.826490]   Vendor: ATA       Model: ST3320833AS       Rev: 3.AH
[   30.827174]   Type:   Direct-Access                      ANSI SCSI revision: 
05
[   30.827769] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
[   30.827811] GSI 17 sharing vector 0xD1 and IRQ 17
[   30.827853] ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [APSJ] -> GSI 22 
(level, low) -> IRQ 209
[   30.828094] PCI: Setting latency timer of device 0000:00:0f.0 to 64
[   30.828157] ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xCC00 irq 209
[   30.828216] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xCC08 irq 209
[   30.831057] Driver 'sd' needs updating - please use bus_type methods
[   30.831169] SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
[   30.831220] SCSI device sda: drive cache: write back

-- 
Can't boot after upgrading to Edgy (AMD64)
https://launchpad.net/bugs/66837

-- 
ubuntu-bugs mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs

Reply via email to