bakker_be wrote: > It seems to work OK on either the SPDIF and the Line Out. Can't verify > if there's any sound though, The SPDIF is still wired wrongly, haven't > got the soldering skills to fix it, and I don't have any headphones with > a 3,5mm jack ... > > Code: -------------------- > > login as: root > [email protected]'s password: > Last login: Sat Nov 29 18:49:28 2014 > [root@wandboard ~]# dmesg > ... > [ 8.850348] usb 1-1: new low-speed USB device number 2 using ci_hdrc > [ 9.027602] input: HOLTEK Wireless USB Device as /devices/soc0/soc.1/2100000.aips-bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1:1.0/input/input0 > [ 9.046878] hid-generic 0003:04D9:A01C.0001: input,hidraw0: USB HID v1.10 Keyboard [HOLTEK Wireless USB Device] on usb-ci_hdrc.1-1/input0 > [ 9.086917] input: HOLTEK Wireless USB Device as /devices/soc0/soc.1/2100000.aips-bus/2184200.usb/ci_hdrc.1/usb1/1-1/1-1:1.1/input/input1 > [ 9.109875] hid-generic 0003:04D9:A01C.0002: input,hidraw1: USB HID v1.10 Mouse [HOLTEK Wireless USB Device] on usb-ci_hdrc.1-1/input1 > [ 9.300790] ov5640_read_reg:write reg error:reg=300a > [ 9.304600] camera ov5640_mipi is not found > [ 9.321081] brcmfmac: F1 signature read @0x18000000=0x9934329 > [ 9.324282] brcmfmac: brcmf_sdio_chip_drivestrengthinit: No SDIO Drive strength init done for chip 4329 rev 3 pmurev 6 > [ 9.652524] brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: Sep 2 2011 14:48:19 version 4.220.48 > [ 9.698783] brcmfmac: brcmf_fil_cmd_data: Failed err=-23 > [ 9.702886] brcmfmac: brcmf_fws_init: failed to set bdcv2 tlv signaling > [ 9.737232] usbcore: registered new interface driver brcmfmac > [ 10.387432] fec 2188000.ethernet eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=2188000.ethernet:01, irq=-1) > [ 10.422566] unable to find transceiver of type USB3 PHY > [ 10.425858] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready > [ 10.431155] dwc3 dwc3.0.auto: no usb3 phy configured > [ 10.465339] platform dwc3.0.auto: Driver dwc3 requests probe deferral > [ 10.474741] ERROR: v4l2 capture: slave not found! > [ 10.535611] evbug: Connected device: input0 (HOLTEK Wireless USB Device at usb-ci_hdrc.1-1/input0) > [ 10.535629] evbug: Connected device: input1 (HOLTEK Wireless USB Device at usb-ci_hdrc.1-1/input1) > [ 13.380587] libphy: 2188000.ethernet:01 - Link is Up - 100/Full > [ 13.385242] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready > [ 15.232170] imx-hdmi-audio imx-hdmi-audio: HDMI Video is not ready! > [ 15.237162] imx-hdmi-audio imx-hdmi-audio: ASoC: can't open platform imx-hdmi-audio: -22 > [ 172.186890] imx-hdmi-audio imx-hdmi-audio: HDMI Video is not ready! > [ 172.192065] imx-hdmi-audio imx-hdmi-audio: ASoC: can't open platform imx-hdmi-audio: -22 > [ 380.378402] imx-hdmi-audio imx-hdmi-audio: HDMI Video is not ready! > [ 380.383443] imx-hdmi-audio imx-hdmi-audio: ASoC: can't open platform imx-hdmi-audio: -22 > -------------------- > >
Does the workaround described here work? https://community.freescale.com/thread/322982 (echo 0 to a specific location). ------------------------------------------------------------------------ Triode's Profile: http://forums.slimdevices.com/member.php?userid=17 View this thread: http://forums.slimdevices.com/showthread.php?t=101624 _______________________________________________ unix mailing list [email protected] http://lists.slimdevices.com/mailman/listinfo/unix
