Thank you ilya. I thought I tried 4.5 as part of my troubleshooting and had an issue using it with vCenter 6 though now I can't recall for sure. I will try that again.
Jacob Seeley Sr. Infrastructure Engineer VertitechIT 413-268-1631 www.vertitechit.com -----Original Message----- From: ilya [mailto:[email protected]] Sent: Friday, July 29, 2016 2:01 PM To: [email protected] Subject: Re: CS 4.8 VMware - Virtual Router stuck at starting Jacob So you are setting a basic zone, which means you have a single network for both hypervisors and guest VMs (or everything). In that case - the control network should 0.0.0.0 - since there are no other networks. I was under assumption you are using advanced zone - but its more clear now. I'd suggest you start off with 4.5 for the time being - while we raise a blocker issue for 4.8 (and possibly 4.9). I'll see if i can spend some cycles to investigate this. Regards ilya On 7/29/16 7:20 AM, Jacob Seeley wrote: > ilya, > > I'm using a Basic zone. Here is the workflow I'm using with actual IP > addresses. Any fields I left out you can assume I leave blank. > > Add Zone > > Zone Type: Basic > Name: ZONE1 > IPv4 DNS: 10.70.116.20 > Internal DNS 1: 10.70.116.20 > Hypervisor: VMware > Network Offering: DefaultSharedNetworkOffering > > Physical Network > > Management: vSwitch Name: vSwitch0 > Guest: vSwitch Name: vSwitch0 > > Pod name: POD1 > Reserved system gateway: 10.70.116.1 > Reserved system netmask: 255.255.255.0 Start Reserved system IP: > 10.70.116.60 End Reserved system IP: 10.70.116.79 > > Guest Gateway: 10.70.116.1 > Guest Netmask: 255.255.255.0 > Guest start IP: 10.70.116.80 > Guest end IP: 10.70.116.99 > > The rest is Storage and is probably irrelevant here. > > After I go through the wizard of adding a zone, it asks me to enable it, > which I do. Without any further action, 2 System VMs (Console and Secondary) > are created. The default CentOS template is downloaded. Both System VMs > receive 2x IP addresses, one on the Pod network and one on the guest network. > > System Storage VM > Public IP address: 10.70.116.81 > Private IP address: 10.70.116.73 > Gateway: 10.70.116.1 > > Console Proxy VM > Public IP address: 10.70.116.80 > Private IP address: 10.70.116.74 > Gateway: 10.70.116.1 > > Only when I initiate my first VM from template (or even ISO) is a > Virtual Router deployed. Like mentioned before, it gets two NICS with the > first one being of Traffic Type Guest and an IP address of 10.70.116.92 and a > second NIC of Traffic Type Control and no IP address assigned (it reports > 0.0.0.0). Ultimately the virtual router gets deployed on the hypervisor > (VMware) but it's useless. The instance I tried deploying ultimately fails. I > suspect that this is the problem or a problem. The virtual router gets an IP > address on the guest network but not the management network. > > Regarding the cloud agent/service (/etc/init.d/cloud) on the virtual > router. I mentioned earlier that I found that /etc/init.d/cloud on the > virtual router fails. I found this happens because > /usr/local/cloud/systemvm never gets populated on the virtual router. > Further down the rabbit hole I go, I see there is a script, > /opt/cloud/bin/patchsystemvm.sh, that is responsible for mounting the > systemvm.iso and unzipping the contents to /usr/local/cloud/systemvm. > Both System VMS (console and secondary) do this but not the virtual > router. From what I can tell, the reason for this as follows. If you > look at the script (found here: > https://github.com/apache/cloudstack/blob/master/systemvm/patches/debi > an/config/opt/cloud/bin/patchsystemvm.sh) > > There is a function of the script called patch_console_proxy. This > function gets called only if the following is satisfied: if [ "$TYPE" > == "consoleproxy" ] || [ "$TYPE" == "secstorage" ] && [ -f > ${PATCH_MOUNT}/systemvm.zip ] > > I've noticed that the value for TYPE in every case I've tried this with the > virtual router is equal to dhcpsrv. According to that script, the function > that gets called for TYPE=dhcpdsrv is dhcpsrvr_svcs. That function does the > following: > > dhcpsrvr_svcs() { > chkconfig cloud off > chkconfig cloud-passwd-srvr on ; > chkconfig haproxy off ; > chkconfig dnsmasq on > chkconfig ssh on > chkconfig nfs-common off > chkconfig portmap off > chkconfig keepalived off > chkconfig conntrackd off > echo "ssh dnsmasq cloud-passwd-srvr apache2" > > /var/cache/cloud/enabled_svcs > echo "cloud nfs-common haproxy portmap" > > /var/cache/cloud/disabled_svcs } > > Here you can see that it turns off the cloud service. As far as I can tell, > my system router is executing this function, so this is expected behavior. > This tells me that the service cloud is to never run when TYPE=dhcpsrv. > > As you mentioned before, I've since tried manually assigning an IP address > NIC1 on the virtual router but it doesn't seem to help or do anything. > > Without ever having a working setup of CloudStack before, it makes it harder > for me to debug the issue since I'm not always sure how something should > work. Unfortunately, I have no choice but to try and make this work on the > VMware hypervisor. I think what I'm going to do now is setup a KVM hypervisor > and see if I can get this working using the same software versions and > workflow. > > Thank you for your help. > > Jacob Seeley > Sr. Infrastructure Engineer > VertitechIT > 413-268-1631 > > www.vertitechit.com > > -----Original Message----- > From: ilya [mailto:[email protected]] > Sent: Friday, July 29, 2016 2:43 AM > To: [email protected] > Subject: Re: CS 4.8 VMware - Virtual Router stuck at starting > > Daren > > I'm also running 4.5.2 - and like the stability we get with it. > > For the features we need, 4.5.2 - has everything that is required, so I dont > see huge benefit of upgrading to latest ACS ATM. Also, our environments are > very large and complex - so upgrade is not something I can take lightly. > > With that said, i do have a small 8 node Lab environment i can try the > upgrade on, it consists of 4 ESXi and 4 KVM nodes - so it should be a fair > test. > > Lets wait for Jacob to respond with his test of setting up IP/Netmask for > eth1 router vm, if it does not help, i'll try to upgrade to see if i can > reproduce the issue. > > Regards > ilya > > On 7/28/16 9:43 PM, Darren Tang wrote: >> Hi ilya: >> I can confirm that issus, please check : >> https://issues.apache.org/jira/browse/CLOUDSTACK-9144 >> When we deployed cloudstack(4.6/4.7/4.8) with vmware(5.x/6.0) in >> basic zone, The VR is nerver leaves the "starting" state. fell back >> to 4.5 is fine. >> Maybe you can test it by yourself. >> >> 2016-07-29 3:24 GMT+08:00 ilya <[email protected]>: >> >>> I guess it would help to know what type of zone you use? >>> >>> Is it advanced, isolated vpc or shared network? what type of isolation? >>> or perhaps basic zone? >>> >>> Lastly, try stopping the iptables and restarting cloud agent (via >>> stop and start) >>> >>> Please see my response in-line >>> >>> On 7/28/16 6:58 AM, Jacob Seeley wrote: >>>> Hi ilya, >>>> >>>> Funny you brought up debugging the router VM. After I responding >>> yesterday, I did just that and I did find some odd things. >>>> Just to be clear (I think we're on the same page), since I'm not >>>> the OP >>> of this thread, the virtual router always gets deployed and it >>> starts up just fine; however, CloudStack reports that it's always stuck in >>> starting. >>> VMs that get deployed ultimately fail. CloudStack reports the router >>> version as UNKNOWN. >>>> Before I provide what I found debugging the router VM, I'll address >>>> some >>> of your points. >>>> >>>> ### FOLLOW-UP QUESTIONS ### >>>> >>>> " Another reason would be an issue of hypervisor accessing the NFS >>>> mount >>> used for secondary storage." >>>> I don't believe this is an issue. The hypervisor (VMware) does >>>> mount the >>> secondary storage via NFS just fine. If this were an issue, I would >>> think the Secondary Storage and Console VMs would not deploy. >>>> >>>> " Use console of vCenter to see what is happening on router vm. You >>>> can >>> login locally with root/password and see the content of >>> /var/log/cloud.out file, paste it on pastebin - if it makes no sense to >>> you..." >>>> It looks like to me that /var/log/cloud.out is only logged to when >>> $CLOUD_DEBUG is set to a non-zero length in the /etc/init.d/cloud script. >>> As such, there isn't even a file for /var/log/cloud.out. Even when I >>> set that variable, I never get anything logged to /var/log/cloud.out. >>> However, there is a /var/log/cloud.log. Here is the contents of that: >>> http://pastebin.com/aaTsRKZE >>>> >>>> " you can also run /etc/init.d/cloud stop and start.. that will >>>> give you >>> a fresh start on logs.." >>>> The service is in a failed state. It's worth noting that this >>>> service is >>> in a started state on the Console and Secondary Storage VMs. >>> >>> this is concerning - see you did "sh -x", read on.. >>> >>>> >>>> " also, confirm that management server can talk to VR on POD IP >>>> (management) on port 3922.." >>>> It appears this is not an issue; see below: >>> >>> 3922 from MS to VR - this is the SSH daemon on VR with private key >>> 8250 from VR to MS - cloudstack java agent on VR talking to MS >>> >>> >>>> >>>> root@r-4-VM:~# telnet 10.70.110.101 8250 Trying 10.70.110.101... >>>> Connected to 10.70.110.101. >>>> Escape character is '^]'. >>>> >>> >>> >>>> ### ROUTE VM DEBUG ### >>>> >>>> Here is what I found with router VM gets deployed (please tell me >>>> if >>> anything seems off): >>>> 2 NICs; only one NIC gets an IP address. CloudStack NIC1 shows an >>>> IP >>> address coming from the defaultGuestNetwork. NIC2 is traffic type >>> Control but has an IP address of 0.0.0.0 >>> >>> It is an issue for concern to see 0.0.0.0 assigned to eth1 >>> >>> Lets assume NIC1 (as eth0) and NIC2 (as eth1). >>> >>> 1) we should not be getting 0.0.0.0 for eth1 - aka control network. >>> This IP should be coming from the POD network range -> when you >>> added a pod - i assume you did it as part of Add Zone wizard... >>> >>> To see the PODIP range, goto UI >>> Infrastructure, Zones, Your Zone, Physical Network, Physical Network >>> 1 (assume you did not create anything special), Management, IP >>> Ranges >>> -> you should see a range defined there and it should not be 0.0.0.0... >>> >>>> From the CloudStack management server, I cannot SSH into the router >>>> VM >>> on NIC1. I've found this is because of iptables rules on the router >>> VM. If I issue a /etc/init.d/iptables-persistent flush on the router >>> VM, I can SSH into the router VM using the SSH key at port 3922. >>>> The service "cloud" is in a failed state. Looking at the cloud init >>> script, I see the following: >>>> >>>> CMDLINE=$(cat /var/cache/cloud/cmdline) >>>> >>>> TYPE="router" >>>> for i in $CMDLINE >>>> do >>>> # search for foo=bar pattern and cut out foo >>>> FIRSTPATTERN=$(echo $i | cut -d= -f1) >>>> case $FIRSTPATTERN in >>>> type) >>>> TYPE=$(echo $i | cut -d= -f2) >>>> ;; >>>> esac >>>> done >>>> >>>> The file cat /var/cache/cloud/cmdline exist; here are the contents: >>>> >>>> template=domP name=r-4-VM eth0ip=10.70.116.75 >>>> eth0mask=255.255.255.0 >>> gateway=10.70.116.1 domain=vit.vertitechit.com cidrsize=24 >>> dhcprange=10.70.116.1 eth1ip=0.0.0.0 eth1mask=0.0.0.0 mgmtcidr= >>> 10.70.110.0/24 localgw=10.70.116.1 sshonguest=true type=dhcpsrvr >>> disable_rp_filter=true extra_pubnics=2 dns1=10.70.10.21 >>> baremetalnotificationsecuritykey=nu1HfF_DpC-gK-G_3y1u54Snb9ruROq-qld >>> O vhnHj4EMypguvtfQu0o18eY3gs81iPZMD2Du1QOUAG5KOfMYXQ >>> baremetalnotificationapikey=CKZoOXffpY5ihjvzly3yD_2t2qaDnFglYFDoeep3 >>> 7 aH1qy5u67aX51ZsuZpZcphfOxJY52rkTlNOl0nkNSyXjQ >>> host=10.70.110.101 port=8080 >>> nic_macs=06:b1:2e:00:00:10|02:00:14:42:00:03 >>>> >>> >>> >>> You can also try updating your /var/cache/cloud/cmdline with proper >>> value for eth1ip=0.0.0.0 eth1mask=0.0.0.0, you can look it up under >>> Infrastructure, Routers, r-4, Nics and look for control nic.. >>> >>> Then try starting the cloud service.. >>> >>> Also, did you enable baremetal support? can you deploy a zone >>> without baremetal support? Perhaps there is a bug on how IPs are >>> assigned to >>> eth1 (control nic)... >>> >>> >>>> The previous code suggests that the value of TYPE starts as router >>>> but >>> will get set to dhcpsrvr, as indicated by the contents of >>> /var/cache/cloud/cmdline. Is this normal? >>>> Further down the script, I see: >>>> >>>> CLOUDSTACK_HOME="/usr/local/cloud" >>> <----------------------------------------Exists >>>> if [ -f $CLOUDSTACK_HOME/systemvm/utils.sh ]; >>> <----------------------------------------Does not exist. Seems odd! >>>> then >>>> . $CLOUDSTACK_HOME/systemvm/utils.sh >>>> else >>>> _failure >>>> fi >>>> >>>> # mkdir -p /var/log/vmops >>>> >>>> start() { >>>> local pid=$(get_pids) >>>> if [ "$pid" != "" ]; then >>>> echo "CloudStack cloud sevice is already running, PID = $pid" >>>> return 0 >>>> fi >>>> >>>> echo -n "Starting CloudStack cloud service (type=$TYPE) " >>>> if [ -f $CLOUDSTACK_HOME/systemvm/run.sh ]; >>> <------------------------------------------------------Does not exist. >>> Seems odd! >>>> then >>>> if [ "$pid" == "" ] >>>> then >>>> (cd $CLOUDSTACK_HOME/systemvm; nohup ./run.sh > $LOG_FILE 2>&1 & ) >>>> pid=$(get_pids) >>>> echo $pid > /var/run/cloud.pid >>>> fi >>>> _success >>>> else >>>> _failure >>>> fi >>>> echo >>>> echo 'start' > $CLOUDSTACK_HOME/systemvm/user_request >>>> } >>>> >>>> I see that it sets CLOUDSTACK_HOME to /usr/local/cloud. This folder >>> exists; however, the script then looks for the file >>> /usr/local/cloud/systemvm/utils.sh. This file doesn't exist. It also >>> looks is supposed to start the script run.sh but that also doesn't >>> exist. This seems like a problem to me. >>>> Here you can see step through when I try to start the cloud service: >>>> >>>> sh -x /etc/init.d/cloud start >>>> + ENABLED=0 >>>> + [ -e /etc/default/cloud ] >>>> + . /etc/default/cloud >>>> + ENABLED=0 >>>> + cat /var/cache/cloud/cmdline >>>> + CMDLINE= template=domP name=r-4-VM eth0ip=10.70.116.75 >>> eth0mask=255.255.255.0 gateway=10.70.116.1 >>> domain=vit.vertitechit.com >>> cidrsize=24 dhcprange=10.70.116.1 eth1ip=0.0.0.0 eth1mask=0.0.0.0 >>> mgmtcidr= >>> 10.70.110.0/24 localgw=10.70.116.1 sshonguest=true type=dhcpsrvr >>> disable_rp_filter=true extra_pubnics=2 dns1=10.70.10.21 >>> baremetalnotificationsecuritykey=nu1HfF_DpC-gK-G_3y1u54Snb9ruROq-qld >>> O vhnHj4EMypguvtfQu0o18eY3gs81iPZMD2Du1QOUAG5KOfMYXQ >>> baremetalnotificationapikey=CKZoOXffpY5ihjvzly3yD_2t2qaDnFglYFDoeep3 >>> 7 aH1qy5u67aX51ZsuZpZcphfOxJY52rkTlNOl0nkNSyXjQ >>> host=10.70.110.101 port=8080 >>> nic_macs=06:b1:2e:00:00:10|02:00:14:42:00:03 >>>> + [ ! -z ] >>>> + LOG_FILE=/dev/null >>>> + TYPE=router >>>> + cut -d= -f1 >>>> + echo template=domP >>>> + FIRSTPATTERN=template >>>> + cut -d= -f1 >>>> + echo name=r-4-VM >>>> + FIRSTPATTERN=name >>>> + cut -d= -f1 >>>> + echo eth0ip=10.70.116.75 >>>> + FIRSTPATTERN=eth0ip >>>> + cut -d= -f1 >>>> + echo eth0mask=255.255.255.0 >>>> + FIRSTPATTERN=eth0mask >>>> + cut -d= -f1 >>>> + echo gateway=10.70.116.1 >>>> + FIRSTPATTERN=gateway >>>> + cut -d= -f1 >>>> + echo domain=vit.vertitechit.com >>>> + FIRSTPATTERN=domain >>>> + cut -d= -f1 >>>> + echo cidrsize=24 >>>> + FIRSTPATTERN=cidrsize >>>> + cut -d= -f1 >>>> + echo dhcprange=10.70.116.1 >>>> + FIRSTPATTERN=dhcprange >>>> + cut -d= -f1 >>>> + echo eth1ip=0.0.0.0 >>>> + FIRSTPATTERN=eth1ip >>>> + cut -d= -f1 >>>> + echo eth1mask=0.0.0.0 >>>> + FIRSTPATTERN=eth1mask >>>> + cut -d= -f1 >>>> + echo mgmtcidr=10.70.110.0/24 >>>> + FIRSTPATTERN=mgmtcidr >>>> + cut -d= -f1 >>>> + echo localgw=10.70.116.1 >>>> + FIRSTPATTERN=localgw >>>> + cut -d= -f1 >>>> + echo sshonguest=true >>>> + FIRSTPATTERN=sshonguest >>>> + cut -d= -f1 >>>> + echo type=dhcpsrvr >>>> + FIRSTPATTERN=type >>>> + cut -d= -f2 >>>> + echo type=dhcpsrvr >>>> + TYPE=dhcpsrvr >>>> + cut -d= -f1 >>>> + echo disable_rp_filter=true >>>> + FIRSTPATTERN=disable_rp_filter >>>> + cut -d= -f1 >>>> + echo extra_pubnics=2 >>>> + FIRSTPATTERN=extra_pubnics >>>> + cut -d= -f1 >>>> + echo dns1=10.70.10.21 >>>> + FIRSTPATTERN=dns1 >>>> + cut -d= -f1 >>>> + echo >>> baremetalnotificationsecuritykey=nu1HfF_DpC-gK-G_3y1u54Snb9ruROq-qld >>> O vhnHj4EMypguvtfQu0o18eY3gs81iPZMD2Du1QOUAG5KOfMYXQ >>>> + FIRSTPATTERN=baremetalnotificationsecuritykey >>>> + cut -d= -f1 >>>> + echo >>> baremetalnotificationapikey=CKZoOXffpY5ihjvzly3yD_2t2qaDnFglYFDoeep3 >>> 7 aH1qy5u67aX51ZsuZpZcphfOxJY52rkTlNOl0nkNSyXjQ >>>> + FIRSTPATTERN=baremetalnotificationapikey >>>> + cut -d= -f1 >>>> + echo host=10.70.110.101 >>>> + FIRSTPATTERN=host >>>> + cut -d= -f1 >>>> + echo port=8080 >>>> + FIRSTPATTERN=port >>>> + cut -d= -f1 >>>> + echo nic_macs=06:b1:2e:00:00:10|02:00:14:42:00:03 >>>> + FIRSTPATTERN=nic_macs >>>> + [ -f /etc/init.d/functions ] >>>> + [ -f ./lib/lsb/init-functions ] >>>> + RETVAL=0 >>>> + CLOUDSTACK_HOME=/usr/local/cloud >>>> + [ -f /usr/local/cloud/systemvm/utils.sh ] _failure [ -f >>>> + /etc/init.d/functions ] echo Failed >>>> Failed >>>> + [ 0 != 0 ] >>>> + exit 0 >>>> >>>> Thoughts? >>>> >>>> Jacob Seeley >>>> Sr. Infrastructure Engineer >>>> VertitechIT >>>> 413-268-1631 >>>> >>>> www.vertitechit.com >>>> >>>> -----Original Message----- >>>> From: ilya [mailto:[email protected]] >>>> Sent: Wednesday, July 27, 2016 8:43 PM >>>> To: [email protected] >>>> Subject: Re: CS 4.8 VMware - Virtual Router stuck at starting >>>> >>>> Hi Jacob >>>> >>>> I gave this a second read - if your issue is Router VM in starting >>>> mode >>>> - but not started - it means cloudstack agent on routerVM cannot >>>> talk to >>> management server on 8250 over POD network. >>>> >>>> Another reason would be an issue of hypervisor accessing the NFS >>>> mount >>> used for secondary storage. >>>> >>>> Use console of vCenter to see what is happening on router vm. You >>>> can >>> login locally with root/password and see the content of >>> /var/log/cloud.out file, paste it on pastebin - if it makes no sense to >>> you... >>>> >>>> you can also run /etc/init.d/cloud stop and start.. that will give >>>> you a >>> fresh start on logs.. >>>> >>>> also, confirm that management server can talk to VR on POD IP >>>> (management) on port 3922.. >>>> >>>> Regards >>>> ilya >>>> >>>> On 7/27/16 9:34 AM, Jacob Seeley wrote: >>>>> ilya, >>>>> >>>>> Here are the contents of the secondary storage: >>>>> >>>>> . >>>>> ./template >>>>> ./template/tmpl >>>>> ./template/tmpl/1 >>>>> ./template/tmpl/1/8 >>>>> ./template/tmpl/1/8/49a4c4ee-ef06-4474-92c3-1d8efb082266.ova >>>>> ./template/tmpl/1/8/template.properties >>>>> ./template/tmpl/1/8/systemvm64template-4.6.0-RC20151104T1522-4.6.0 >>>>> - >>>>> vmw >>>>> are.ovf >>>>> ./template/tmpl/1/8/systemvm64template-4.6.0-RC20151104T1522-4.6.0 >>>>> - >>>>> vmw >>>>> are-disk3.vmdk >>>>> ./template/tmpl/1/7 >>>>> ./template/tmpl/1/7/template.properties >>>>> ./template/tmpl/1/7/0098d168-4985-3b33-9840-eb5848d2f385.ova >>>>> ./template/tmpl/1/7/CentOS5.3-x86_64.ovf >>>>> ./template/tmpl/1/7/CentOS5.3-x86_64-disk1.vmdk >>>>> ./template/tmpl/1/7/CentOS5.3-x86_64.mf >>>>> ./systemvm >>>>> ./systemvm/systemvm-4.8.0.1.iso >>>>> ./systemvm/.lck-bf162a0100000000 >>>>> ./snapshots >>>>> ./volumes >>>>> >>>>> I've noticed that both the Secondary Storage VM and Console Proxy >>>>> VM >>> mount this ISO and as stated before, they come up just fine. >>>>> >>>>> Regards, >>>>> >>>>> Jacob Seeley >>>>> Sr. Infrastructure Engineer >>>>> VertitechIT >>>>> 413-268-1631 >>>>> >>>>> www.vertitechit.com >>>>> >>>>> -----Original Message----- >>>>> From: ilya [mailto:[email protected]] >>>>> Sent: Wednesday, July 27, 2016 3:22 AM >>>>> To: [email protected] >>>>> Subject: Re: CS 4.8 VMware - Virtual Router stuck at starting >>>>> >>>>> Jacob >>>>> >>>>> The upgrade usually occurs though systemvm.iso - that is generated >>>>> by >>> cloudstack on the first start. >>>>> >>>>> Please show the content of your secondary store specifically >>>>> >>>>> /mnt/[secondary-storage]/systemvm >>>>> >>>>> Regards >>>>> ilya >>>>> >>>>> On 7/25/16 11:19 AM, Jacob Seeley wrote: >>>>>> Here is a pastebin snippet the management-server.log - >>>>>> http://pastebin.com/GCLm53Gz >>>>>> >>>>>> Hopefully the relevant data is in there. >>>>>> >>>>>> I made sure to start from scratch for this example. Everything >>>>>> from >>> the vSphere ESXi to the vCenter to the CentOS 7 with CloudStack >>> install is fresh. I deployed a new instance in CloudStack, a VM >>> internally named i-2-3-VM with an IP address of 192.168.0.78. This >>> prompted CloudStack to deploy a VR. The VR is called r-4-VM with an IP >>> address of 192.168.0.79. >>>>>> >>>>>> Thank you, >>>>>> >>>>>> Jacob Seeley >>>>>> Sr. Infrastructure Engineer >>>>>> VertitechIT >>>>>> 413-268-1631 >>>>>> >>>>>> www.vertitechit.com >>>>>> >>>>>> -----Original Message----- >>>>>> From: Suresh Sadhu [mailto:[email protected]] >>>>>> Sent: Monday, July 25, 2016 1:37 AM >>>>>> To: [email protected] >>>>>> Subject: Re: CS 4.8 VMware - Virtual Router stuck at starting >>>>>> >>>>>> please upload the logs in the issue. >>>>>>> On Jul 5, 2016, at 8:46 AM, Darren Tang >>>>>>> <[email protected]> >>> wrote: >>>>>>> >>>>>>> https://issues.apache.org/jira/browse/CLOUDSTACK-9144 >>>>>>> >>>>>>> 2016-07-04 19:41 GMT+08:00 Glenn Wagner <[email protected]>: >>>>>>> >>>>>>>> Hi, >>>>>>>> >>>>>>>> What template are you using to start your first VM? - the >>>>>>>> default vmware template? >>>>>>>> If you look in vcenter , what does the console show you ? >>>>>>>> >>>>>>>> >>>>>>>> Glenn >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> [email protected] >>>>>>>> www.shapeblue.com >>>>>>>> 2nd Floor, Oudehuis Centre, 122 Main Rd, Somerset West, Cape >>>>>>>> Town 7130South Africa @shapeblue >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> -----Original Message----- >>>>>>>> From: Pascal R. [mailto:[email protected]] >>>>>>>> Sent: Monday, 04 July 2016 1:26 PM >>>>>>>> To: [email protected] >>>>>>>> Subject: CS 4.8 VMware - Virtual Router stuck at starting >>>>>>>> >>>>>>>> hi, >>>>>>>> >>>>>>>> we have a CS4.8 deployment with VMWare 5.5. >>>>>>>> >>>>>>>> When trying to launch the first VM, the VS is created. VS >>>>>>>> starts up, but in CS, it stuck with "starting" state. >>>>>>>> >>>>>>>> i can't find any usefull information in the logs. >>>>>>>> >>>>>>>> any hint? >>>>>>>> >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> DISCLAIMER >>>>>> ========== >>>>>> This e-mail may contain privileged and confidential information >>>>>> which >>> is the property of Accelerite, a Persistent Systems business. It is >>> intended only for the use of the individual or entity to which it is >>> addressed. If you are not the intended recipient, you are not >>> authorized to read, retain, copy, print, distribute or use this >>> message. If you have received this communication in error, please >>> notify the sender and delete all copies of this message. Accelerite, >>> a Persistent Systems business does not accept any liability for virus >>> infected mails. >>>>>> >>> >>
