Naveed Ahmad <nahmad <at> intercloudsys.com> writes: > > > On 04/06/2015 06:08 PM, > raviraj.velankar <at> tcs.com wrote: > > > Hi Tomasz, > We have done the exact config. given on below URL which you have shared but still we did not get the desired output. Routes for virtual network does not appear in global routing table of physical gateway router. > Have you done this type of configuration if yes then request you to share network topology with ip address schema and configuration if possible. Thanks. > > Regards, > Raviraj VelankarFrom: "Tomasz Charewicz" > <tomasz <at> charewicz.net> > To: "Raviraj Velankar" > <raviraj.velankar <at> tcs.com>, "" > <users <at> lists.opencontrail.org> > Date: 04/01/2015 11:51 AM > Subject: Re: [Users] External Gateway Router Configuration > Hi, I think that article will be helpful. http://www.opencontrail.org/how-to-setup-opencontrail-gateway-juniper- mx-cisco-asr-and-software-gw/ > -- best regards Tomasz Charewicz On 2015-04-01 08:17:39, Raviraj Velankar > <raviraj.velankar <at> tcs.com> wrote: > Dear All, > We would like to enable communication between VMs in virtual network inside contrail and other external networks which are beyond external physical gateway router. For that we have configured external Juniper router as a BGP peer to existing Control node. But > would like to know what configuration or configuration changes need to be done on physical juniper router so that it enables communication between virtual and physical network. We have installed Juniper contrail 2.0 with icehouse openstack and MX 240 router. > > Kindly inform if any sample config example or configuration required for physical juniper router. > > Thanks & Regards, > Raviraj Velankar > From: Raviraj Velankar/MUM/TCS > > To: users <at> lists.opencontrail.org > > Date: 03/16/2015 04:55 PM > > Subject: Integration of Juniper Contrail with existing Openstack Server > > > Dear Team, > We would like to know how to integrate Juniper contrail 2.01 with existing Openstack servers. I know there is procedure to add compute node manually. In the same way if I have installed Juniper Contrail on physical servers along with compute nodes and required > to integrate existing Openstack server with that Contrail. Kindly inform if any procedure for the same. > > Thanks & Regards, > Raviraj Sudhakar Velankar > Tata Consultancy Services > Cell:- +91-09833503544 > Mailto: > raviraj.velankar <at> tcs.com > Website: http://www.tcs.com > ____________________________________________ > Experience certainty. IT Services > Business Solutions > Consulting > ____________________________________________ > From: Raviraj Velankar/MUM/TCS > > To: users <at> lists.opencontrail.org > > Date: 02/11/2015 05:45 PM > > Subject: Juniper Contrail Deployment > > > Dear Team, > We are trying to install Juniper contrail with Icehouse Openstack. However we are facing few issues in deployment. Below is the brief about setup. > > Total 3 physical rack mount servers. We have installed CentOS 6.5 with Contrail 2.0.22 & Icehouse Openstack. Server-1 consist of Control, Config , Analytics and Icehouse Openstack functions. Server-2 is a compute node. We have also installed Qemu KVM on both > servers. For server-3 we are planning to install VMware ESXi and planned to add as a compute node in existing setup. > > Below are some of the issues : > Not able to properly spin-up service VMs such as firewall or load balancers. We have observed only one network interface exist in the newly spawned virtual machine instead of two interfaces. When we tried to add another interface but it was not getting added. > Would like to know which vendor service appliances such as Juniper vSRX or other vendor FW, load balancer has been completely tested in Juniper Contrail & Openstack Icehouse environment and how to create additional interfaces in the juniper vSRX firewall. > > Request you to provide step by step process for VMware Hypervisor ( ESXi) integration as a compute node to Juniper Contrail. Certain steps given in Juniper document with fab commands but would like to know step by step detailed process. Request your help/expertise. > Thanks. > Regards, > Raviraj Velankar > =====-----=====-----===== > Notice: The information contained in this e-mail > message and/or attachments to it may contain > confidential or privileged information. If you are > not the intended recipient, any dissemination, use, > review, distribution, printing or copying of the > information contained in this e-mail message > and/or attachments to it are strictly prohibited. If > you have received this communication in error, > please notify us by reply e-mail or telephone and > immediately and permanently delete the message > and any attachments. Thank you > _______________________________________________ Users mailing list > Users <at> lists.opencontrail.org > http://lists.opencontrail.org/mailman/listinfo/users_lists.opencontrail. org > > > Hi Raj, > Can you state the exact problem you are facing after doing configs from the URL?. Plus please provide a basic network diagram showing the nodes and external gateway. Thanks > > Regards, > Naveed Ahmad > Network Engineer - InterCloud Systems > O:+1-212-202-2930 > C:+1-929-265-3334 > > > _______________________________________________ > Users mailing list > Users <at> lists.opencontrail.org > http://lists.opencontrail.org/mailman/listinfo/users_lists.opencontrail. org >
Hi, I'm facing the same challenge where control nodes have BGP established with vSRX used as an external gateway and receiving routes into the VRF configured on the SRX. however since the routes aren't available in the default routing instance the VM's are not reachable. Instance Import doesn't seem to work here as the Routing Instance is a VPN Instance (that's what commit check mentions on SRX) It will be of great help if anyone can help with the SRX/MX configuration exactly as used in your setup. Regards, Lalit _______________________________________________ Users mailing list [email protected] http://lists.opencontrail.org/mailman/listinfo/users_lists.opencontrail.org
