I don’t see anything unusual.
I think before that, I need confirmation to the basic question I had.
I’m attaching the pic again for reference.
The host1 can reach host2 either over the 172.29.54.x network via eth0
(DHCP’ed address) or over NIC interfaces via eth4 or eth5 (with static
ipaddr).
So what should ideally be the management IP address in testbed.py?
My control_data looks like:
control_data = {
host1 : { ‘ip: ‘1.1.1.1/24’, ‘gw’ : 172.29.48.1’, ‘device’ : ‘eth4’ }
host2 : { ‘ip: ‘1.1.1.2/24’, ‘gw’ : 172.29.48.1’, ‘device’ : ‘eth4’ }


Thanks,
harish  



>Please take a look at /etc/network/interfaces to see if eth0 has the
>right entries.
>The Contrail installation process add the vhost0 interface to this file
>(in place of eth0).
>But if you hit some errors, perhaps this file was not in a sane state.
>
>Raja 
>
>On 9/21/16, 4:37 PM, "Patil, Harish" <harish.pa...@cavium.com> wrote:
>
>    Hi Raja,
>    I have a strange issue.
>    After issuing fab upgrade_kernel the kernel is downgraded to
>    3.13.0.85-generic as expected. But after that I can’t ping/ssh the
>eth0
>    interface of host1. I tried all other ways to make it work. Have
>someone
>    else seen the same issue? Even though I boot back to 4.2.0-27-generic
>    kernel I can’t ping. Could the contrail SW be interfering with it?
>    
>    Thanks,
>    Harish
>    
>    
>    >Thanks Raja.
>    >I will try downgrading the kernel and see if I can get over this.
>    >Can you please re-confirm that my understanding of control_data
>section is
>    >correct, I shall skip VLAN.
>    >
>    >Harish
>    >
>    >>Hi Harish,
>    >>    Yes, you need “fab upgrade_kernel”. It could downgrade the
>kernel.
>    >>You can avoid VLAN in the control_data,
>    >>but the gateway may be required.
>    >>
>    >>Raja
>    >>
>    >>On 9/20/16, 10:23 AM, "Users on behalf of Patil, Harish"
>    >><users-boun...@lists.opencontrail.org on behalf of
>    >>harish.pa...@cavium.com> wrote:
>    >>
>    >>    Hello,
>    >>    I¹m trying out Contrail SW installation for the first time. I
>have an
>    >>    issue in installing it.
>    >>    
>    >>    Attached are the following to help debug the issue:
>    >>    1) Diagram that shows the setup. Its a simple two-node topology
>with
>    >>a
>    >>    2x25G NIC connected back-back.
>    >>    The testbed.py is configured based on that. All the
>configuration is
>    >>    happening over the lab network 172.29.54.x connected via eth0
>    >>interfaces.
>    >>    
>    >>    The end objective is to create VMs on both nodes using
>Openstack and
>    >>ping
>    >>    between both VMs using VXLAN as the tunneling protocol using
>the NIC
>    >>    interfaces.
>    >>    
>    >>    2) The fab setup_all log that shows the failure.
>    >>    
>    >>    3) testbed.py
>    >>    
>    >>    Additional details:
>    >>    
>    >>    1) Contrail SW:
>    >>    contrail-install-packages_3.0.2.0-51-ubuntu-14-04kilo_all.deb
>    >>    
>    >>    2) OS:
>    >>    root@dut4092:/opt/contrail/utils# uname -a
>    >>    Linux dut4092 4.2.0-27-generic #32~14.04.1-Ubuntu SMP Fri Jan 22
>    >>15:32:26
>    >>    UTC 2016 x86_64 x86_64 x86_64 GNU/Linux
>    >>    
>    >>    Questions:
>    >>    
>    >>    - The documentation says 3.13.0-34 is the recommended kernel
>version.
>    >>Is
>    >>    it a must?
>    >>    Does fab upgrade_kernel_all actually downgrades the linux
>kernel?  I
>    >>    didn¹t experiment by downgrading the kernel since the current
>    >>installation
>    >>    issue does not seem related to linux kernel version.
>    >>    
>    >>    - There is a section called ³control_data² in testbed.py. I
>believe
>    >>this
>    >>    is where we need to specify eth4 and eth5 as NIC interfaces over
>    >>which the
>    >>    VM traffic has to flow.
>    >>    But I don¹t want to specify gateway and VLAN. Is it possible?
>    >>    Eg:
>    >>    #    host1 : { 'ip': '192.168.10.1/24', 'gw' : '192.168.10.254',
>    >>    'device':'eth0', 'vlan': '224' },
>    >>    
>    >>    Thanks,
>    >>    
>    >>    Harish
>    >>    
>    >>    
>    >>
>    >>
>    >
>    >
>    >
>    
>    
>    
>
>


_______________________________________________
Users mailing list
Users@lists.opencontrail.org
http://lists.opencontrail.org/mailman/listinfo/users_lists.opencontrail.org

Reply via email to