But there is next problem. I cannot start or migrate VM to the host with libvirt upgraded to version 1.0.0, the error is:
failed: error: cannot open file 'one/one-3-8-0': No such file or directory Configured the same as others nodes where it is working. Maybe the compiled libvirt doesn't have rbd module loaded? 2014-04-03 12:43 GMT+02:00 Leszek Master <keks...@gmail.com>: > It worked. Thank you very much for your help ! :) > > > 2014-04-03 11:03 GMT+02:00 James Dobson <jdob...@velocix.com>: > > You need to upgrade the version of libvirt, basically support for >> openvswitch wasn't added until a later version if you don't have the later >> version you have to use brcompat. >> >> >> >> http://libvirt.org/formatnetwork.html >> >> >> >> bridge >> >> This network describes either 1) an existing host bridge that was >> configured outside of libvirt (if a <bridge name='xyz'/> element has >> been specified, Since 0.9.4), 2) an existing Open vSwitch bridge that was >> configured outside of libvirt (if both a <bridge name='xyz'/> element >> *and* a <virtualport type='openvswitch'/> have been specified Since >> 0.10.0) 3) an interface or group of interfaces to be used for a "direct" >> connection via macvtap using macvtap's "bridge" mode (if the forward >> element has one or more <interface> subelements, Since 0.9.4) (see Direct >> attachment to physical >> interface<http://libvirt.org/formatdomain.html#elementsNICSDirect>for >> descriptions of the various macvtap modes). libvirt doesn't attempt to >> manage the bridge interface at all, thus the <bridge> element's stp and >> delay attributes are not allowed; no iptables rules, IP addresses, or >> DHCP/DNS services are added; at the IP level, the guest interface appears >> to be directly connected to the physical interface.Since 0.9.4 >> >> >> >> This also may help.. >> >> >> >> >> http://blog.scottlowe.org/2012/11/05/compiling-libvirt-1-0-0-on-ubuntu-12-04-and-12-10/ >> >> >> >> I was lucky that in centos 6 the epel repository had a later version I >> could use. >> >> >> >> HTH, >> >> >> >> James >> >> >> >> *From:* users-boun...@lists.opennebula.org [mailto: >> users-boun...@lists.opennebula.org] *On Behalf Of *Leszek Master >> *Sent:* 03 April 2014 09:40 >> *To:* Stefan Kooman; Users OpenNebula >> *Subject:* Re: [one-users] Opennebula and openvswitch problem. >> >> >> >> I'm waiting for official relese of next LTS version, i can use only LTS >> in my production, so i was testing it on the 12.04. If there isn't any >> official manual how ot solve this problem i'll upgrade my distro and try >> then :) Thanks for your help. >> >> >> >> 2014-04-03 9:25 GMT+02:00 Stefan Kooman <ste...@bit.nl>: >> >> Quoting Leszek Master (keks...@gmail.com): >> > Still the same problem: >> > >> > failed: error: Unable to add bridge br0 port vnet0: Operation not >> supported >> > >> > sudo ovs-vsctl show >> > e2e80002-00ea-464d-9c62-5af5e0889d81 >> > Bridge "br0" >> > Port "eth1" >> > Interface "eth1" >> > Port "br0" >> > Interface "br0" >> > type: internal >> > ovs_version: "1.4.6" >> > leni@node-03:~$ sudo brctl show >> > bridge name bridge id STP enabled interfaces >> > leni@node-03:~$ >> > >> > >> > Tryied updating openvswitch from 1.4 to 1.9, the problem stays the same. >> > The only thing to get this working for now is to load brcompat module to >> > os, but it's problematic with new nodes. Any one have solution to this >> > problem? >> >> I believe I managed to get it going on Precise, but I had some issues, >> just like you. It's been some time ago though. Ubuntu Precise Trusty >> Tahr is due in a few weeks. Any particular reason you would want to stay >> on Precise?. >> >> >> Gr. Stefan >> >> -- >> | BIT BV http://www.bit.nl/ Kamer van Koophandel 09090351 >> | GPG: 0xD14839C6 +31 318 648 688 / i...@bit.nl >> >> >> > >
_______________________________________________ Users mailing list Users@lists.opennebula.org http://lists.opennebula.org/listinfo.cgi/users-opennebula.org