The output show that only one destination was used by dispatcher (which
was directly pushed into the message, so no pending destination in case
of failover) - see the "273" AVP with value "1".
Regards,
Bogdan-Andrei Iancu
OpenSIPS Founder and Developer
http://www.opensips-solutions.com
On 17.09.2014 18:06, Satish Patel wrote:
Here you go
/sbin/opensips[28000]: Sending call to ===> Freeswitch
/sbin/opensips[28000]: INFO:avpops:ops_print_avp: p=0x7f9ed01dd420,
flags=0x0000
/sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011name=<274>
/sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011id=<10>
/sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011val_int=<0>
/sbin/opensips[28000]: INFO:avpops:ops_print_avp: p=0x7f9ed01df208,
flags=0x0000
/sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011name=<273>
/sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011id=<9>
/sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011val_int=<1>
/sbin/opensips[28000]: INFO:avpops:ops_print_avp: p=0x7f9ed01e6518,
flags=0x0002
/sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011name=<272>
/sbin/opensips[28000]: INFO:avpops:ops_print_avp: #011#011#011id=<12>
/sbin/opensips[28000]: INFO:avpops:ops_print_avp:
#011#011#011val_str=< / 0>
/sbin/opensips[28000]: dispatcher: Attempting to dispatch call to
sip:182.xx.xx.xxx:5071
/sbin/opensips[28005]: Inside dispatcher failure route
/sbin/opensips[28005]: ds_dispatcher <null> <null> > <null>
/sbin/opensips[28005]:
R-DISPATCHER-ROLLOVER:fU4SNHMvcNmnjW19gsSj0g..-S No more gateways in
route set
On Wed, Sep 17, 2014 at 10:25 AM, Bogdan-Andrei Iancu
<[email protected] <mailto:[email protected]>> wrote:
Hi,
As mentioned, place the avp_print() just after you did the
ds_select_dst(), before relaying to the first destination.
Regards,
Bogdan-Andrei Iancu
OpenSIPS Founder and Developer
http://www.opensips-solutions.com
On 17.09.2014 14:09, Satish Patel wrote:
Confirmed probing/inactive thing is working,
Now problem is failover not working, ds_next_dst() not able to
find next gateway and it says no more gateway available. If
you check my script, i am calling failure route and inside it
calling ds_next_dst() but you are saying do avp_print() on
ds_select_dst() it won't print anything because after failure
you are in failure route block.
Please advice if my script has any issue.
Sent from my iPhone
On Sep 17, 2014, at 3:30 AM, Bogdan-Andrei Iancu
<[email protected] <mailto:[email protected]>> wrote:
Hi Satish,
Use the "opensipsctl fifo ds_list" to see the status of
the gws in realtime . Be sure that once a gw is in
non-active state (probing or inactive), it will not be
used again for routing. Just take care of doing the
ds_next_dst() in order to jump to the next available gw.
If you do the avp_print() after ds_select_dst(), you can
see how many other gw are prepared to used in case of
failover.
Regards,
Bogdan-Andrei Iancu
OpenSIPS Founder and Developer
http://www.opensips-solutions.com
On 16.09.2014 21:02, Satish Patel wrote:
After doing couple of TEST look like its marking
"Probing" for failed gateway but not auto failover to
next gateway, i meant call get disconnect and i need
to re-initiate call then all call goes to second
active gateway..
I believe it should first mark gateway "Probing" and
then fall-back to second gateway automatically instead
of call disconnect and i am getting 503 error code on
my SIP Phone.
_______________________________________________
Users mailing list
[email protected]
http://lists.opensips.org/cgi-bin/mailman/listinfo/users
